Extract the GPLL reference frequency from CCK and use it in the
GPU freq<->opcode conversions on VLV/CHV. This eliminates all the
assumptions we have about which divider is used for which czclk
frequency.
Note that unlike most clocks from CCK, the GPLL ref clock is a divided
down version of the CZ clock rather than the HPLL clock. CZ clock itself
is a divided down version of the HPLL clock though, so in effect it just
gets divided down twice.
While at it, throw in a few comments explaining the remaining constants
for anyone who later wants to compare this to the spreadsheets.
v2: Add slow/fast notes for CHV clocks (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457120584-26080-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
- On Super-H PFC (Renesas) controllers: only use dummies on
legacy systems. This fixes a serious ethernet regression on
a Renesas board.
- Pistachio: Fix errors in the pin table.
- Allwinner SunXi: fix the external interrupts to work.
- Intel: fix so the high level interrupts start working, and
fix a spurious interrupt issue.
- Qualcomm ipq4019: fix the number of GPIOs provided (bump
to 100), correct register offsets and handle GPIO mode
properly.
- Revert the revert on the revert so that Xway has a .to_irq()
callback again.
- Minor fixes to errorpaths and debug info.
- A MAINTAINERS update.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=atcX
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is a set of pin control fixes for the v4.6 series.
A bit bigger than what I hoped for, but all fixes are confined to
drivers, a few of them also targeted to stable.
Summary:
- On Super-H PFC (Renesas) controllers: only use dummies on legacy
systems. This fixes a serious ethernet regression on a Renesas
board.
- Pistachio: Fix errors in the pin table.
- Allwinner SunXi: fix the external interrupts to work.
- Intel: fix so the high level interrupts start working, and fix a
spurious interrupt issue.
- Qualcomm ipq4019: fix the number of GPIOs provided (bump to 100),
correct register offsets and handle GPIO mode properly.
- Revert the revert on the revert so that Xway has a .to_irq()
callback again.
- Minor fixes to errorpaths and debug info.
- A MAINTAINERS update"
* tag 'pinctrl-v4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
Revert "Revert "pinctrl: lantiq: Implement gpio_chip.to_irq""
pinctrl: qcom: ipq4019: fix register offsets
pinctrl: qcom: ipq4019: fix the function enum for gpio mode
pinctrl: qcom: ipq4019: set ngpios to correct value
pinctrl: nomadik: fix pull debug print inversion
MAINTAINERS: pinctrl: samsung: Add two new maintainers
pinctrl: intel: implement gpio_irq_enable
pinctrl: intel: make the high level interrupt working
pinctrl: freescale: imx: fix bogus check of of_iomap() return value
pinctrl: sunxi: Fix A33 external interrupts not working
pinctrl: pistachio: fix mfio84-89 function description and pinmux.
pinctrl: sh-pfc: only use dummy states for non-DT platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=eZp5
-----END PGP SIGNATURE-----
Merge tag 'media/v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some bug fixes on au0828 and snd-usb-audio:
- the au0828+snd-usb-audio MC patch broke several things and produced
some race conditions. Better to revert the patches, and re-work on
them for a next version
- fix a regression at tuner disable links logic
- properly handle dev_state as a bitmask"
* tag 'media/v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] Revert "[media] media: au0828 change to use Managed Media Controller API"
[media] Revert "[media] sound/usb: Use Media Controller API to share media resources"
[media] au0828: Fix dev_state handling
[media] au0828: fix au0828_v4l2_close() dev_state race condition
[media] media: au0828 fix to clear enable/disable/change source handlers
[media] v4l2-mc: cleanup a warning
[media] au0828: disable tuner links and cache tuner/decoder
With the change to stashing just the IOVA-page-aligned remainder of the
CPU-page offset rather than the whole thing, the failure path in
__invalidate_sg() also needs tweaking to account for that in the case of
differing page sizes where the two offsets may not be equivalent.
Similarly in __finalise_sg(), lest the architecture-specific wrappers
later get the wrong address for cache maintenance on sync or unmap.
Fixes: 164afb1d85 ("iommu/dma: Use correct offset in map_sg")
Reported-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Cc: stable@ver.kernel.org # v4.4+
Signed-off-by: Joerg Roedel <jroedel@suse.de>
After a suspend-resume cycle, the resumed kernel has no idea what the
booted kernel may have done to the GuC before replacing itself with the
resumed image. In particular, it may have already loaded the GuC with
firmware, which will then cause this kernel's attempt to (re)load the
firmware to fail (GuC program memory is write-once!). The symptoms
(GuC firmware reload fails after hibernation) are further described
in the Bugzilla reference below.
So let's *always* reset the GuC just before (re)loading the firmware;
the hardware should then be in a well-known state, and we may even
avoid some of the issues arising from unpredictable timing.
Also added some more fields & values to the definition of the GUC_STATUS
register, which is the key diagnostic indicator if the GuC load fails.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Alex Dai <yu.dai@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94390
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Due to timing issues in the HW, some of the status bits required for GuC
authentication occasionally don't get set; when that happens, the GuC
cannot be initialized and we will be left with a wedged GPU. The W/A
suggested is to perform a soft reset of the GuC and attempt to reload
the F/W again for few times before giving up.
As the failure is dependent on timing, tests performed by triggering
manual full gpu reset (i915_wedged) showed that we could sometimes hit
this after several thousand iterations, but sometimes tests ran even
longer without any issues. Reset and reload mechanism proved helpful
when we indeed hit f/w load failure, so it is better to include this
to improve driver stability.
This change implements the following WAs,
WaEnableuKernelHeaderValidFix:skl,bxt
WaEnableGuCBootHashCheckNotSet:skl,bxt
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
-ftracer can duplicate asm blocks causing compilation to fail in
noclone functions. For example, KVM declares a global variable
in an asm like
asm("2: ... \n
.pushsection data \n
.global vmx_return \n
vmx_return: .long 2b");
and -ftracer causes a double declaration.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: stable@vger.kernel.org
Cc: kvm@vger.kernel.org
Reported-by: Linda Walsh <lkml@tlinx.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a vCPU runs on a nohz_full core, the hrtimer used by
the lapic emulation code can be migrated to another core.
When this happens, it's possible to observe milisecond
latency when delivering timer IRQs to KVM guests.
The huge latency is mainly due to the fact that
apic_timer_fn() expects to run during a kvm exit. It
sets KVM_REQ_PENDING_TIMER and let it be handled on kvm
entry. However, if the timer fires on a different core,
we have to wait until the next kvm exit for the guest
to see KVM_REQ_PENDING_TIMER set.
This problem became visible after commit 9642d18ee. This
commit changed the timer migration code to always attempt
to migrate timers away from nohz_full cores. While it's
discussable if this is correct/desirable (I don't think
it is), it's clear that the lapic emulation code has
a requirement on firing the hrtimer in the same core
where it was started. This is achieved by making the
hrtimer pinned.
Lastly, note that KVM has code to migrate timers when a
vCPU is scheduled to run in different core. However, this
forced migration may fail. When this happens, we can have
the same problem. If we want 100% correctness, we'll have
to modify apic_timer_fn() to cause a kvm exit when it runs
on a different core than the vCPU. Not sure if this is
possible.
Here's a reproducer for the issue being fixed:
1. Set all cores but core0 to be nohz_full cores
2. Start a guest with a single vCPU
3. Trace apic_timer_fn() and kvm_inject_apic_timer_irqs()
You'll see that apic_timer_fn() will run in core0 while
kvm_inject_apic_timer_irqs() runs in a different core. If
you get both on core0, try running a program that takes 100%
of the CPU and pin it to core0 to force the vCPU out.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
commit 1e133ab296 ("s390/mm: split arch/s390/mm/pgtable.c") dropped
some changes from commit a3a92c31bf ("KVM: s390: fix mismatch
between user and in-kernel guest limit") - this breaks KVM for some
memory sizes (kvm-s390: failed to commit memory region) like
exactly 2GB.
Cc: Dominik Dingel <dingel@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
iommu drivers that support the standard DT bindings use a of_xlate
callback pointer, but that is only part of struct iommu_ops when
CONFIG_OF_IOMMU is enabled, leading to build errors in randconfig
builds when that is not provided:
drivers/iommu/mtk_iommu.c:497:2: error: unknown field 'of_xlate' specified in initializer
.of_xlate = mtk_iommu_of_xlate,
^
drivers/iommu/mtk_iommu.c:497:14: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.of_xlate = mtk_iommu_of_xlate,
^~~~~~~~~~~~~~~~~~
drivers/iommu/mtk_iommu.c:497:14: note: (near initialization for 'mtk_iommu_ops.domain_get_attr')
We can work around it by adding more #ifdefs in each driver, but
it seems nicer to just allow setting the pointer even if it is
unused. This makes the driver code look nicer, and it gives better
compile-time coverage when test building on other architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0df4fabe20 ("iommu/mediatek: Add mt8173 IOMMU driver")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The patch "scsi: rescan VPD attributes" introduced a regression in which
devices that don't support VPD were being scanned for VPD attributes
anyway. This could cause issues for some devices and should be avoided
so the check for scsi_level has been moved out of scsi_add_lun and into
scsi_attach_vpd so that all callers will not scan VPD for devices that
don't support it.
[mkp: Merge fix]
Fixes: 09e2b0b146 ("scsi: rescan VPD attributes")
Cc: <stable@vger.kernel.org> #v4.5+
Suggested-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support and PCI IDs for more Broxton host controllers
Other BXT IDs were added in v4.4 so cc'ing stable. This patch
is dependent on commit 163cbe31e5 ("mmc: sdhci-pci: Fix card
detect race for Intel BXT/APL") but that is already in stable
since v4.4.4.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Both the oom and vmap notifier callbacks have a loop to acquire the
struct_mutex and set the device as uninterruptible, within a certain
time. Refactor the common code into a pair of functions.
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459848145-24042-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
If the core runs out of vmap address space, it will call a notifier in
case any driver can reap some of its vmaps. As i915.ko is possibily
holding onto vmap address space that could be recovered, hook into the
notifier chain and try and reap objects holding onto vmaps.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Roman Pen <r.peniaev@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: linux-mm@kvack.org
Cc: linux-kernel@vger.kernel.org
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459777603-23618-4-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
vmaps are temporary kernel mappings that may be of long duration.
Reusing a vmap on an object is preferrable for a driver as the cost of
setting up the vmap can otherwise dominate the operation on the object.
However, the vmap address space is rather limited on 32bit systems and
so we add a notification for vmap pressure in order for the driver to
release any cached vmappings.
The interface is styled after the oom-notifier where the callees are
passed a pointer to an unsigned long counter for them to indicate if they
have freed any space.
v2: Guard the blocking notifier call with gfpflags_allow_blocking()
v3: Correct typo in forward declaration and move to head of file
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Roman Peniaev <r.peniaev@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: linux-mm@kvack.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Andrew Morton <akpm@linux-foundation.org> # for inclusion via DRM
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459777603-23618-3-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Since we only attempt to purge an object if can_release_pages() report
true, we should also only add it to the count of potential recoverable
pages when can_release_pages() is true.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459777603-23618-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Since we enqueued the frame that was supposed to be sent
during the SP, and that frame may very well cary the
IEEE80211_TX_STATUS_EOSP bit, we may never close the SP
(WLAN_STA_SP will never be cleared). If that happens, we
will not open any new SP and will never respond to any poll
frame from the client.
Clear WLAN_STA_SP manually if a frame that was polled during
the SP is queued because of a starting A-MPDU session. The
client may not see the EOSP bit, but it will at least be
able to poll new frames in another SP.
Reported-by: Alesya Shapira <alesya.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove erroneous comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible that the station is connected to an AP
with bandwidth of 80+80MHz or 160MHz. In such cases
there is no need to perform an upgrade as the maximal
supported bandwidth is 80MHz.
In addition, when upgrading and setting center_freq1
and bandwidth to 80MHz also set center_freq2 to 0.
Fixes: 0fabfaafec ("mac80211: upgrade BW of TDLS peers when possible"
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Frames that are sent between
ampdu_action(IEEE80211_AMPDU_TX_START) and the move to the
HT_AGG_STATE_OPERATIONAL state are buffered.
If we try to start an A-MPDU session while the peer is
sleeping and polling frames with U-APSD, we may have frames
that will be buffered by ieee80211_tx_prep_agg. These frames
have IEEE80211_TX_CTL_NO_PS_BUFFER set since they are sent to
a sleeping client and possibly IEEE80211_TX_STATUS_EOSP.
If the frame is buffered, we need clear these two flags
since they will be re-sent after the move to
HT_AGG_STATE_OPERATIONAL state which is very likely to
happen after the SP ends.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 976bd9efda ("mac80211: move beacon_loss_count into ifmgd")
removed the member from the sta_info struct but the description stayed
lingering. Remove it.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add documentation for the flag for duplication check.
Fixes the following warning when running make htmldocs:
warning: Enum value 'RX_FLAG_DUP_VALIDATED' not described in enum 'mac80211_rx_flags'
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
[fix description]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By default, the rhashtable logic will fail to insert
objects if the key-chains are too long and un-balanced.
In the degenerate case where mac80211 is creating many
virtual interfaces connected to the same peer(s), this
case can happen.
St insecure_elasticity to true to allow chains to grow
as long as needed.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[remove message, change commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The original hand-implemented hash-table in mac80211 couldn't result
in insertion errors, and while converting to rhashtable I evidently
forgot to check the errors.
This surfaced now only because Ben is adding many identical keys and
that resulted in hidden insertion errors.
Cc: stable@vger.kernel.org
Fixes: 7bedd0cfad ("mac80211: use rhashtable for station table")
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The min_def chanctx is affected not only by the current chandef, but
sometimes also by other stations on the vif. There's a valid scenario
where a TDLS peer can widen its BW, thereby causing the min_def
to increase.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous approach simply ignored chandef restrictions when calculating
the appropriate peer BW for a WIDER_BW peer. This could result in a
regulatory violation if both peers indicated 80MHz support, but the
regdomain forbade it.
Change the approach to setting a WIDER_BW peer's BW. Don't exempt it from
the chandef width at first. If during TDLS negotiation the chandef width
is upgraded, update the peer's BW to match.
Fixes: 0fabfaafec ("mac80211: upgrade BW of TDLS peers when possible")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if the current chandef width is equal to the station's max-BW, it
doesn't mean it's a valid width for TDLS. Make sure to always check
regulatory constraints in these cases.
Fixes: 0fabfaafec ("mac80211: upgrade BW of TDLS peers when possible")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Buffered multicast frames must be passed to the driver directly via
drv_tx instead of going through the txq, otherwise they cannot easily be
scheduled to be sent after DTIM.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put a reminder that during device removal drivers should revert all PM
runtime changes from the probe.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added missing model 0x46.
Tested-and-reported-by: Piotr Maksymiuk <piotr.maksymiuk@movishell.pl>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The comment in file header doesn't hold true anymore, drop it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No code change. Only added kernel doc style comments for structures.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When user sets performance policy using cpufreq interface, it is possible
that because of policy->max limits, the actual performance is still
limited. But the current implementation will silently switch the
policy to powersave and start using powersave limits. If user modifies
any limits using intel_pstate sysfs, this is actually changing powersave
limits.
The current implementation tracks limits under powersave and performance
policy using two different variables. When policy->max is less than
policy->cpuinfo.max_freq, only powersave limit variable is used.
This fix causes the performance limits variable to be used always when
the policy is performance.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull MIPS fixes from Ralf Baechle:
"This is the first round of MIPS fixes for 4.6:
- Fix spelling mistakes all over arch/mips
- Provide __bswapsi2 so XZ kernel compression will build with older GCC
- ATH79 clock fixes.
- Fix clock-rated copy-paste erros in ATH79 DTS.
- Fix gisb-arb compatible string for 7435 BMIPS
- Enable NAND and UBIFS support in CI20.
- Fix BUG() assertion caused by inapropriate smp_processor_id() use.
- Fix exception handling issues for the sake of debuggers
- Fix the last remaining instance of irq_to_gpio in the db1xxx_ss PCMCIA code
- Fix MSA unaligned load failures
- Panic if kernel is configured for a not TLB-supported page size
- Bail out on unsupported relocs in modules.
- Partial fix for Qemu breakage after recent IPI rewrite
- Wire up the preadv2 and pwrite2 syscalls
- Fix the ar724x clock calculation"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: traps.c: Verify the ISA for microMIPS RDHWR emulation
MIPS: BMIPS: Fix gisb-arb compatible string for 7435
MIPS: Bail on unsupported module relocs
MIPS: dts: qca: ar9132_tl_wr1043nd_v1.dts: use "ref" for reference clock name
MIPS: ath79: Fix the ar913x reference clock rate
MIPS: ath79: Fix the ar724x clock calculation
dt-bindings: clock: qca,ath79-pll: fix copy-paste typos
MIPS: traps: Correct the SIGTRAP debug ABI in `do_watch' and `do_trap_or_bp'
FIRMWARE: Broadcom: Fix grammar of warning messages in bcm47xx_sprom.c.
MIPS: ci20: Enable NAND and UBIFS support in defconfig.
MIPS: Fix misspellings in comments.
MIPS: tlb-r4k: panic if the MMU doesn't support PAGE_SIZE
MIPS: zboot: Remove copied source files on clean
MIPS: zboot: Fix the build with XZ compression on older GCC versions
MIPS: Wire up preadv2 and pwrite2 syscalls.
MIPS: cpu_name_string: Use raw_smp_processor_id().
pcmcia: db1xxx_ss: fix last irq_to_gpio user
MIPS: Fix MSA ld unaligned failure cases
MIPS: Fix broken malta qemu
- Safely migrate event channels between CPUs.
- Fix CPU hotplug.
- Maintainer changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXAkQtAAoJEFxbo/MsZsTRpAoH/R0mVySTK3RloxRo4SPDWs//
3EIgDFBCde/JfDmhJw7OTLC6oHExq/ObBunV4I6HSStDYjZfHnMXTe7uiRo6oOUt
ql8/k1P4NM202L2qkjZU89ObPwOMbx50NiHtVG3JAIydZc/jgn4/brow9ZymDAUd
lp85Oj0d66uM5iIY9YVa5nY/calt5W0rr9EoV93HSf6GFefNJKXJ5u3KW8IgMyIl
I4/y8GraQLAcXBcmrOny51nlIxsiv1wTssJfExH49/8In3JH3SlbZDGuEiIovPUC
jJ96Tr/oOhFyPZIM3J7pFYpvn4en84V07zbaWcEUmVf8capv3pjwJNg2Xx64FdI=
=bSO5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.6-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from David Vrabel:
"Regression and bug fixes for 4.6-rc2:
- safely migrate event channels between CPUs
- fix CPU hotplug
- maintainer changes"
* tag 'for-linus-4.6-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
MAINTAINERS: xen: Konrad to step down and Juergen to pick up
xen/events: Mask a moving irq
Xen on ARM and ARM64: update MAINTAINERS info
xen/x86: Call cpu_startup_entry(CPUHP_AP_ONLINE_IDLE) from xen_play_dead()
xen/apic: Provide Xen-specific version of cpu_present_to_apicid APIC op
These should be set by default otherwise the UVD/VCE performance
won't be optimal.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
and revert fix following it accordingly
Revert "drm/amdgpu: stop trying to suspend UVD sessions v2"
Revert "drm/amdgpu: fix the UVD suspend sequence order"
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes ttm on platforms like PPC460 where the CPU
is in 32-bit mode, but the physical addresses are
>32 bits.
Extracted from a patch by Hans Verkuil.
Tested-by: Julian Margetson <runaway@candw.ms>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Julian Margetson <runaway@candw.ms>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 82ef33af9d. It turns
out these machines are still out there, and the original patch broke
them. So revert it, adding back the driver, so people's machines still
work properly.
Reported-by: James Cameron <quozl@laptop.org>
Cc: Shraddha Barke <shraddha.6596@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function parse_platform_config in firmware.c calls crc32_le.
Building without CRC32 selected causes a link error:
drivers/built-in.o: In function `parse_platform_config':
(.text+0x92ffa): undefined reference to `crc32_le'
Signed-off-by: Markus Böhme <markus.boehme@mailbox.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This lot are either dependent on patches from the merge window or just came
in recently enough that they ended up in this tree.
* core
- The watermark for the buffers was given a value that meant that it was
impossible to actually set the watermark to anything sensible.
* at91_adc
- Fix a build config dependency on HAS_IOMEM
* bmc150
- Fix wrong output on big endian systems
* bmg160
- Fix wrong output on big endian systems
- Fix an issue in which the regmap return value was stored to the buffer
rather than the value actually being read in a bulk read.
* inv_mpu6050
- Fix an indirect build config dependency on HAS_IOMEM
* max30100
- Fix an error in fifo check condition that leads to a double read of the
final reading.
* st_magn
- Make sure ST_MAGN_TRIGGER_SET_STATE is always defined to avoid a build
error for relatively obscure config combinations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=j/qV
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.6b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.6 cycle.
This lot are either dependent on patches from the merge window or just came
in recently enough that they ended up in this tree.
* core
- The watermark for the buffers was given a value that meant that it was
impossible to actually set the watermark to anything sensible.
* at91_adc
- Fix a build config dependency on HAS_IOMEM
* bmc150
- Fix wrong output on big endian systems
* bmg160
- Fix wrong output on big endian systems
- Fix an issue in which the regmap return value was stored to the buffer
rather than the value actually being read in a bulk read.
* inv_mpu6050
- Fix an indirect build config dependency on HAS_IOMEM
* max30100
- Fix an error in fifo check condition that leads to a double read of the
final reading.
* st_magn
- Make sure ST_MAGN_TRIGGER_SET_STATE is always defined to avoid a build
error for relatively obscure config combinations.
Pull quota fixes from Jan Kara:
"Fixes for oopses when the new quotactl gets used with quotas disabled"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ocfs2: Fix Q_GETNEXTQUOTA for filesystem without quotas
quota: Handle Q_GETNEXTQUOTA when quota is disabled
This fixes the incorrect variable assignment on error path in
br_sysfs_addbr for when the call to kobject_create_and_add
fails to assign the value of -EINVAL to the returned variable of
err rather then incorrectly return zero making callers think this
function has succeededed due to the previous assignment being
assigned zero when assigning it the successful return value of
the call to sysfs_create_group which is zero.
Signed-off-by: Bastien Philbert <bastienphilbert@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull f2fs fixes from Jaegeuk Kim.
* tag 'f2fs-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs:
f2fs: retrieve IO write stat from the right place
f2fs crypto: fix corrupted symlink in encrypted case
f2fs: cover large section in sanity check of super
pskb_may_pull() can change skb->data, so we have to load ptr/optr at the
right place.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
