Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to ixgbe and e1000e.
Jacob provides a ixgbe patch to fix the configure_rx patch to properly
disable RSC hardware logic when a user disables it. Previously we only
disabled RSC in the queue settings, but this does not fully disable
hardware RSC logic which can lead to unexpected performance issues.
Emil provides three fixes for ixgbe. First fixes the ethtool loopback
test when DCB is enabled, where the frames may be modified on Tx
(by adding VLAN tag) which will fail the check on receive. Then a fix
for QSFP+ modules, limit the speed setting to advertise only one speed
at a time since the QSFP+ modules do not support auto negotiation.
Lastly, resolve an issue where the driver will display incorrect info
for QSFP+ modules that were inserted after the driver has been loaded.
David Ertman provides to fixes for e1000e, one removes a comparison to
the boolean value true where evaluating the lvalue will produce the
same result. The other fixes an error in the calculation of the
rar_entry_count, which causes a write of unkown/undefined register
space in the MAC to unknown/undefined register space in the PHY.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When copying the MAC RAR registers to PHY there is an error in the
calculation of the rar_entry_count, which causes a write of unknown/
undefined register space in the MAC to unknown/undefined register space in
the PHY.
This patch fixes the overrun with writing to the PHY RAR and also fixes the
ethtool offline register tests so that the correctly addressed registers
have the appropriate bitmasks for R/W and RO bits for affected parts.
Shawn Rader gets credit for finding and fixing the register overrun.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
CC: Shawn Rader <shawn.t.rader@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removing a comparison to the boolean value true where simply interrogating
the lvalue will produce the same result.
Signed-off-by: David Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves an issue where the driver will display incorrect info
for Q/SFP+ modules that were inserted after the driver has been loaded.
This patch adds a call to identify_phy() in ixgbe_get_settings() prior to
calling get_link_capabilities() which needs the PHY data in order to
determine the correct settings.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
QSFP+ modules do not support auto negotiation and should advertise only
one speed at a time.
This patch adds logic in ethtool to allow setting and reporting the
advertised speed at either 1Gbps or 10Gbps, but not both. Also limits
the speed set in ixgbe_sfp_link_config_subtask() to highest supported.
Previously the link was set to whatever the supported speeds were.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch disables DCB prior to running the loopback test.
When DCB is enabled the frames may be modified on Tx (by adding vlan tag)
which will fail the check on Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the configure_rx path in order to properly disable RSC
hardware logic when the user disables it. Previously we only disabled RSC in the
queue settings, but this does not fully disable hardware RSC logic which can
lead to some unexpected performance issues.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.
Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle). Otherwise the handler is
reentered over and over again.
The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared. Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'. Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If rx_urb allocation fails in mcs_setup_urbs(), tx_urb leaks.
If mcs_receive_start() fails in mcs_net_open(), the both urbs are not deallocated.
The patch fixes the issues and by the way fixes label indentation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is down, CQs are freed. We must check the device state
to avoid issuing firmware commands on non existing CQs.
CC: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/dec/tulip/de4x5.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/amd/sun3lance.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/ibm/ehea/ehea_main.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/adi/bfin_mac.c.
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VM is providing an iSCSI target and the LUN is used by the
backend domain, the generated skbs for direct I/O writes to the disk
have large, multi-page skb->data but no frags.
With some lengths and starting offsets, xen_netbk_count_skb_slots()
would be one short because the simple calculation of
DIV_ROUND_UP(skb_headlen(), PAGE_SIZE) was not accounting for the
decisions made by start_new_rx_buffer() which does not guarantee
responses are fully packed.
For example, a skb with length < 2 pages but which spans 3 pages would
be counted as requiring 2 slots but would actually use 3 slots.
skb->data:
| 1111|222222222222|3333 |
Fully packed, this would need 2 slots:
|111122222222|22223333 |
But because the 2nd page wholy fits into a slot it is not split across
slots and goes into a slot of its own:
|1111 |222222222222|3333 |
Miscounting the number of slots means netback may push more responses
than the number of available requests. This will cause the frontend
to get very confused and report "Too many frags/slots". The frontend
never recovers and will eventually BUG.
Fix this by counting the number of required slots more carefully. In
xen_netbk_count_skb_slots(), more closely follow the algorithm used by
xen_netbk_gop_skb() by introducing xen_netbk_count_frag_slots() which
is the dry-run equivalent of netbk_gop_frag_copy().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 989038e217 ("tg3: Don't turn off
led on 5719 serdes port 0") added code to skip turning led off on port
0 of the 5719 since it powered down other ports. This workaround needs
to be enabled on the 5720 as well.
Cc: stable@vger.kernel.org
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c8d68e6be1
(tuntap: multiqueue support) only call free_netdev() on error in
tun_set_iff(). This causes several issues:
- memory of tun security were leaked
- use after free since the flow gc timer was not deleted and the tfile
were not detached
This patch solves the above issues.
Reported-by: Wannes Rombouts <wannes.rombouts@epitech.eu>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure a format string cannot accidentally leak into the
kthread_run() call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control is defined in the four EEPROM sections but the driver only reads
from section 0.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem where some ports can fail to initialize on a
cold boot. This patch adds an additional call to read the PHY id for i354
devices in order workaround the hardware problem.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
struct ce_sendlist is useless as we always add just one buffer onto it.
And most importantly, it's ugly as it doesn't use skb properly.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The peer PHY mode for 11ac operation needs to be determined
properly based on the channel bandwidth being used. Fix
this so that the proper mode is given to the firmware.
kvalo: earlier we used 11na-ht20 in STA mode for 11ac AP peer, this
patch changes that to 11ac-vht80. I didn't notice any change in
throughput in my tests, but nevertheless it's the right thing
to do.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Just to unify with the rest of debug messages. Minimal functional changes,
only major ones are removal of the awkward "else" style in debug
messages.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix them to follow the general logging style in ath10k.
While at it, add print id chip_id to the debug log.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
core.c mostly deals with driver and firmware starting related
actions. And we can use the boot level also in other components,
like PCI and HTT.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
John W. Linville says:
====================
This is a pull request for a few early fixes for the 3.12 stream.
Alexey Khoroshilov corrects a use-after-free issue on rtl8187 found
by the Linux Driver Verification project.
Arend van Spriel provides a brcmfmac patch to fix a build issue
reported by Randy Dunlap.
Hauke Mehrtens offers a bcma fix to properly account for the storage
width of error code values before checking them.
Solomon Peachy brings a pair of cw1200 fixes to avoid hangs in that
driver with SPI devices. One avoids transfers in interrupt context,
the other fixes a locking issue.
Stanislaw Gruszka changes the initialization of the rt2800 driver to
avoid a freeze, addressing a bug in the Red Hat bugzilla.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Same narrative as eb2dc35d99 ("r8169: RxConfig
hack for the 8168evl.") regarding AMD IOMMU errors.
RTL_GIGA_MAC_VER_36 - 8168f as well - has not been reported to behave the
same.
Tested-by: David R <david@unsolicited.net>
Tested-by: Frédéric Leroy <fredo@starox.org>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the device list from the Windows driver description files
included with a new Qualcomm MDM9615 based device, "Alcatel-sbell
ASB TL131 TDD LTE", from China Mobile. This device is tested
and verified to work. The others are assumed to work based on
using the same Windows driver.
Many of these devices support multiple QMI/wwan ports, requiring
multiple interface matching entries. All devices are composite,
providing a mix of one or more serial, storage or Android Debug
Brigde functions in addition to the wwan function.
This device list included an update of one previously known device,
which was incorrectly assumed to have a Gobi 2K layout. This is
corrected.
Reported-by: 王康 <scateu@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series implements the new i40e driver for Intel's upcoming
Intel(R) Ethernet Controller XL710 Family of devices.
V7: many changes from a few comments:
use linux errno types
change I40E_SUCCESS to 0, standardize returns
change s32 return values to int
use void return values where possible
prefer use of int over i40e_status
V6: rename Kbuild to Makefile
rename i40e_mem[set|cpy] to regular memset/memcpy
V5: remove sysfs support from this set, will rearchitect
changes from community comments
V4: addresses remaining community comments, mostly trivial edits.
major sparse based cleanup of possible endian issues
removal of most of __func__ references
sizeof(*var) instead of sizeof(struct ...)
change 'NULL ==' tests to !NULL
implement xps
use kernel bitshift macros (upper_32_bits, etc)
V3: many more individual comments addressed, thanks reviewers! Many
other changes due to internal review and development.
V2: each patch has individual comments, in general, feedback from the
list was applied and addressed. Many changes due to internal review
and coding as well.
V1: initial send
Let me start by saying thanks and we appreciate any time spent by
those of you who review and comment on this new driver, and we will
attempt to address and respond to all issues brought to our attention.
I tried to break the patches up to ease review, but the series should
apply and still be bisectable, as the last patch adds the driver to
the kernel compile with CONFIG_I40E.
This driver is for a brand new bit of silicon that has a different
design than other Intel Ethernet silicon, and therefore needed a new
driver.
The hardware has quite a bit of capability and this driver is only
meant to provide basic functionality at first. Future patches will
continue to add functionality and bug fixes.
This initial release is very early in the product cycle with the intent
of getting initial support into the kernel before users have the
hardware available to purchase. A software development manual is not
ready yet but will be available when the hardware ships.
The driver development model and interaction with community submitted
patches *will not be any different* than what we are currently doing
today. We plan to continue established processes.
An associated i40evf driver has been posted for review.
List of tools we ran in preparation:
way more sparse clean
make W=1, W=2 clean
checkpatch (almost) clean
total: 1 errors, 4 warnings, 30461 lines checked
NOTE: Ignored message types: LONG_LINE
- issues have been addressed and the remainders
are noise.
codespell clean
smatch (almost) clean with a couple minor warnings
coccicheck clean
namespacecheck clean
allmodconfig clean
ppc64 build clean (untested)
This driver is a team effort, thank you to Joseph Gasparakis,
Shannon Nelson, Anjali Singhai-Jain, Mitch Williams, Neerav
Parikh, Vasu Dev, Kavindya Deegala, Yi Zou, and PJ Waskiewicz.
TODO (known issues)
BQL implementation
finish rtnl_stat64 locking (we have a patch but debugging it)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The "id" variable was being incremented in common code, but only
initialized and used in IPv4 code. We move the increment to the IPv4
code too, and then legitimately use the uninitialized_var() macro to
avoid the gcc 4.6 warning that 'id' may be used uninitialized.
Note that gcc 4.7 does not warn.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/broadcom/bcm63xx_enet.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/korina.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently macvlan calls skb_clone in macvlan_broadcast but checks
for a NULL return in macvlan_broadcast_one instead. This is
needlessly confusing and may lead to bugs introduced later.
This patch moves the error check to where the skb_clone call is.
The only other caller of macvlan_broadcast_one never passes in a
NULL value so it doesn't need the check either.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c: In function 'qlcnic_handle_fw_message':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c:922:4: warning: overflow in implicit constant conversion [-Woverflow]
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We make bond_arp_rcv global so it can be used in bond_sysfs if the bond
interface is up and arp_interval is being changed to a positive value
and cleared otherwise as per Jay's suggestion.
This also fixes a problem where bond_arp_rcv was set even though
arp_validate was disabled while the bond was up by unsetting recv_probe
in bond_store_arp_validate and respectively setting it if enabled.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to protect store_arp_validate via rtnl because it can race with
mode changing and we can end up having arp_validate set in a mode
different from active-backup.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization bnx2x allocates significant amounts of memory
(for rx data, rx SGEs, TPA pool) using atomic allocations.
I received a report where bnx2x failed to allocate SGEs and it had
to fall back to TPA-less operation.
Let's use GFP_KERNEL allocations during initialization, which runs
in process context. Add gfp_t parameters to functions that are used
both in initialization and in the receive path.
Use an unlikely branch in bnx2x_frag_alloc() to avoid atomic allocation
by netdev_alloc_frag(). The branch is taken several thousands of times
during initialization, but then never more. Note that fp->rx_frag_size
is never greater than PAGE_SIZE, so __get_free_page() can be used here.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After an MC reboot, the datapath may be running a different firmware
variant and have different capabilities. It is critical that we know
the current capabilities so that we can pass valid flags to
MC_CMD_INIT_EVQ.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Rename efx_ef10_init_capabilities() to the more specific
efx_ef10_init_datapath_caps().
Stop accepting short responses to MC_CMD_GET_CAPABILITIES; we
don't need to support pre-production firmware.
Move the check for RX prefix support from efx_ef10_probe() into
efx_ef10_init_datapath_caps() and use consistent error messages
for missing TSO support and missing RX prefix support.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
If the MC reboots then the stats it reports to us will have been
reset. We need to reset ours to get efx_update_diff_stat() working
properly.
(This is a re-run of commit 876be083b6 'sfc: Reset driver's
MAC stats after MC reboot seen'.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
