Try the completion before we start the FLL so that if an interrupt was
delayed long enough for us to miss it we don't wait for the completion
it signalled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8983 is a low power, high quality stereo CODEC
designed for portable multimedia applications. Highly flexible
analogue mixing functions enable new application features,
combining hi-fi quality audio with voice communication.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should spot them anyway on state changes but logging them gives us
better time information about when the misconfiguration happened.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we have interrupts then wait for the FLL lock interrupt rather than
using dead reckoning when waiting for the FLL to start.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The individual devices should set the flag dcs_done_irq in the hubs
shared data structure to indicate that they will flag the interrupt
by calling wm_hubs_dcs_done().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This ensures appropriate clocking for bypass paths to speaker and
headphone and direct voice paths on affected revisions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Chip documentation explicitly requires that the reset values
of reserved register bits are left untouched. It is possible
there are differences between STA326 and STA328 or future
chip revisions in these bits, and clobbering them might
cause malfunction.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The STA32x has a number of preset EQ settings, but also
allows full user control of the biquad filter coeffcients
(when "Automode EQ" is set to "User").
Each biquad has five signed, 24bit, fixed-point coefficients
representing the range -1...1. The five biquad coefficients
can be uploaded in one atomic operation into on-chip
coefficient RAM.
There are also a few prescale, postscale and mixing
coefficients, in the same numeric format and range
(a negative coefficient inverts phase).
These coefficients are made available as SNDRV_CTL_ELEM_TYPE_BYTES
mixer controls.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The legacy mode has been accidentaly removed by commit:
ASoC: twl6040: add all ABE DAIs
Add back the twl6040-hifi dai.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the PLL handling has been simplified, and
rebased on 0, there is no longer need for converting
the PLL ID.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Avoid configuring the PLL several times during audio startup.
We can configure the PLL at prepare time with parameters collected
earlier hw_param, and set_dai_sysclk calls.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can manage the sample rate constraints without the need
to maintain a variable and a pointer.
This simplifies the handling of the constraint, and makes it
more robust.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is better if the selection between the Low power,
and High performance PLL is handled within the codec
driver, not in machine driver(s) to avoid duplicated
code, and also to have consistent tracking of the selected
PLL, and the resulting differences in supported sample
rates.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the variable names to be neutral (not refering to HS).
This will ease up the introduction of PLL selection, which
going to use the same enum strings.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The twl6040_request_irq/free_irq inline functions are going
to be removed, so replace them with direct calls.
The irq number is provided by the core driver via resource.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now we have supply widgets there's no need to open code the handling of
the ACTIVE bit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Now we have supply widgets there's no need to open code the handling of
the ACTIVE bit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Commit af46800 ("ASoC: Implement mux control sharing") revealed that
"Left Line1[L | R] Mux" and "Right Line1[L | R] Mux" widgets were pointing
to the same kcontrols and codec registers and thus soc-core falsely detected
them as shared controls. This is actually wrong since there are separate
registers in hardware that configure Line1L to RADC and Line1R to LADC cross
connects so these muxes should not be shared.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Enable ramp down/up step to be configured based on
platform.
Signed-off-by: Axel Castaneda Gonzalez <x0055901@ti.com>
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set default sysclk constraints to high performance mode.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove dependency between pll (hppll, lppll) and headset power
mode (low-power, high-performance), as headset power mode can
be used with any pll.
A new control is created to allow headset power mode configuration
from userspace. Changing headset power mode during earpiece related
usecases is not propagated down to the codec as earpiece requires
HS DAC in HP mode.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add other supported sample rates to LP and HP modes.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add all DAIs to fully support OMAP4 ABE.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert TWL6040 CODEC driver into a TWL6040 MFD child, it implies
that MFD-level operations like register accesses, clock setting
and power management are done through MFD APIs, not directly by
CODEC driver anymore. To avoid conflicts with the other MFD child,
vibrator registers are skipped in CODEC driver.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This delay is very conservative.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
Allign the platform data names for twl4030 audio submodule:
twl4030_audio_data: for the core MFD driver
twl4030_codec_data: for ASoC codec driver
twl4030_vibra_data: for the input/ForceFeedback driver
To avoid breakage, change all depending drivers, files
to use the new types.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Rename the driver, and header file from twl4030-codec to
twl4030-audio.
To avoid breakage change depending drivers at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Misael Lopez Cruz <misael.lopez@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
More for neatness than any actual performance improvement.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
It was consistently wrong for everything except WM8993 so should be no
functional change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.comm>
This patch adds support for the Analog Devices ADAV801 and ADAV803 audio codec.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the sound/ directory there are two files (flagged by 'make
versioncheck'); sound/pci/asihpi/asihpi.c and
sound/soc/codecs/wm8991.c that include linux/version.h although they
don't need it. This patch removes the unneeded includes.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
