ipv6: Remove all uses of LL_ALLOCATED_SPACE
The macro LL_ALLOCATED_SPACE was ill-conceived. It applies the
alignment to the sum of needed_headroom and needed_tailroom. As
the amount that is then reserved for head room is needed_headroom
with alignment, this means that the tail room left may be too small.
This patch replaces all uses of LL_ALLOCATED_SPACE in net/ipv6
with the macro LL_RESERVED_SPACE and direct reference to
needed_tailroom.
This also fixes the problem with needed_headroom changing between
allocating the skb and reserving the head room.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4: Remove all uses of LL_ALLOCATED_SPACE
The macro LL_ALLOCATED_SPACE was ill-conceived. It applies the
alignment to the sum of needed_headroom and needed_tailroom. As
the amount that is then reserved for head room is needed_headroom
with alignment, this means that the tail room left may be too small.
This patch replaces all uses of LL_ALLOCATED_SPACE in net/ipv4
with the macro LL_RESERVED_SPACE and direct reference to
needed_tailroom.
This also fixes the problem with needed_headroom changing between
allocating the skb and reserving the head room.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most machines dont use RPS/RFS, and pay a fair amount of instructions in
netif_receive_skb() / netif_rx() / get_rps_cpu() just to discover
RPS/RFS is not setup.
Add a jump_label named rps_needed.
If no device rps_map or global rps_sock_flow_table is setup,
netif_receive_skb() / netif_rx() do a single instruction instead of many
ones, including conditional jumps.
jmp +0 (if CONFIG_JUMP_LABEL=y)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers (e.g. ath9k) assume that it's safe to go into low-power mode
immediately after the idle state changes. To support that, mac80211 even
calls drv_flush() before that happens.
In some instances, mac80211 sent a packet right after recalculating the
idle state, this patch fixes that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused function parameters in the following functions:
minstrel_calc_rate_ewma()
minstrel_ht_calc_tp()
minstrel_aggr_check()
minstrel_ht_set_rate()
Signed-off-by: Patrick Kelle <patrick.kelle81@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We recently introduced a return here, but we need to call kfree
first.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sk_buff structs should be freed using kfree_skb().
This was introduced recently in 029458212 "mac80211: Save probe
response data for bss".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Finding the group index for a specific rate is done by looping through
all groups and returning if the correct one is found. This code is
called for each tx'ed frame and thus it makes sense to reduce its
runtime.
Do this by calculating the group index by this formula based on the SGI
and HT40 flags as well as the stream number:
idx = (HT40 * 2 * MINSTREL_MAX_STREAMS) +
(SGI * MINSTREL_MAX_STREAMS) +
(streams - 1)
Hence, the groups are ordered by th HT40 flag first, then by the SGI
flag and afterwards by the number of used streams.
This should reduce the runtime of minstrel_ht_get_group_idx
considerable.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The drivers are not required to fill in rate->count if rate->idx is set
to -1. Hence, we should first check rate->idx before accessing
rate->count.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The shared key authentication frame that needs to be
encrypted (the third one in the shared key handshake)
is directly encrypted in ieee80211_send_auth and the
IEEE80211_TX_INTFL_DONT_ENCRYPT is set. All others
are not encrypted, so the only way to get to this is
erroneously on no-monitor AP side.
Remove the special case for authentication frames to
fix the AP shared key side when operating without
cooked monitor interfaces -- with cooked monitor the
IEEE80211_TX_INTFL_DONT_ENCRYPT also gets set, so we
never get here -- an AP never encrypts auth frames.
Without this patch, an AP operating in WEP mode with
my no-monitor patches would erroneously encrypt all
authentication frames, instead of none.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a crash when non existing IPv6 route is tried to be changed.
When new destination node was inserted in middle of FIB6 tree, no relevant
sanity checks were performed. Later route insertion might have been prevented
due to invalid request, causing node with no rt info being left in tree.
When this node was accessed, a crash occurred.
Patch adds missing checks in fib6_add_1()
Signed-off-by: Matti Vaittinen <Mazziesaccount@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the /sys/class/net/DEV/queues/Q/tx_timeout attribute
containing the total number of timeout events on the given queue. It
is always available with CONFIG_SYSFS, independently of
CONFIG_RPS/XPS.
Credits to Stephen Hemminger for a preliminary version of this patch.
Tested:
without CONFIG_SYSFS (compilation only)
with sysfs and without CONFIG_RPS & CONFIG_XPS
with sysfs and without CONFIG_RPS
with sysfs and without CONFIG_XPS
with defaults
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes following warning:
net/core/net-sysfs.c:921:6: warning: symbol 'numa_node' shadows an earlier one
include/linux/topology.h:222:1: originally declared here
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing spaces around multiplication operator.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_queue_xmit() consumes its own skb, so the call to dev_kfree_skb()
in lowpan_fragment_xmit() is a double free.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only distinct use is checking if NETIF_F_NOCACHE_COPY should be
enabled by default. The check heuristics is altered a bit here,
so it hits other people than before. The default shouldn't be
trusted for performance-critical cases anyway.
For all other uses NETIF_F_NO_CSUM is equivalent to NETIF_F_HW_CSUM.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: changed loop in ethtool_set_features() per Ben's suggestion
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the only place left where dev->features are directly
exposed to userspace.
I know checkpatch.pl complains about __ethtool_{get,set}_flags(), but
the code is easier to read this way.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As all drivers are converted, we may now remove discrete offload setting
callback handling.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge multicast snooping of ICMPv6 would incorrectly report a checksum problem
when used with Ethernet devices like sky2 that use CHECKSUM_COMPLETE.
When bytes are removed from skb, the computed checksum needs to be adjusted.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Martin Volf <martin.volf.42@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netstamp_needed seems a good candidate to jump_label conversion.
This avoids 3 conditional branches per incoming packet in fast path.
No measurable difference, given that these conditional branches are
predicted on modern cpus. Only a small icache reduction, thanks to the
unlikely() stuff.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Kirby reported divides by zero errors in __tcp_select_window()
This happens when inet_csk_route_child_sock() returns a NULL pointer :
We free new socket while we eventually armed keepalive timer in
tcp_create_openreq_child()
Fix this by a call to tcp_clear_xmit_timers()
[ This is a followup to commit 918eb39962 (net: add missing
bh_unlock_sock() calls) ]
Reported-by: Simon Kirby <sim@hostway.ca>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Simon Kirby <sim@hostway.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make __l2cap_global_chan_by_addr similar to other find functions.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This make it easier to see what is the real reason for loop to exit.
skb_queue_next return valid skb or garbage, not NULL.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Make it easier to see what is loop break condition.
skb_queue_next return valid skb or garbage, not NULL.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Due to ERTM reliability L2CAP channel needs to be disconnected if
adding to srej list failed.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The mgmt_start_discovery command contains the type of discovery that
should be started so this should be passed to the start_discovery
function. This patch doesn't yet add any action depending on the type of
the requested discovery.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The command complete event was completely missing for this command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The management protocol uses a single byte for error codes (aka command
status). In some places this value is directly copied from HCI and in
other a POSIX error number is used. This makes it impossible for
user-space to uniquily decipher the meaning of an error.
To solve this issue a new mgmt-specific set of error codes is added
along with a conversion table for HCI status values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When the adapter state is already what is requested it's more friendly
to user-space to simply report success than to send a EALREADY error
message.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When possible cmd_complete should be returned instead of cmd_status
since it contains the remote address (this helps user-space track what
exactly failed).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The kernel needs to know whether it should connect to a device over
BR/EDR or over LE. This is particularly important in the future when
dual-mode device may be connectable also over LE. It is also important
if/when we decide to move the LE advertisement cache from the kernel
into user-space. Adding the type to the mgmt command also ensures
conformance with the latest mgmt API spec.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patches creates mgmt_stop_discovery_failed() which removes
pending MGMT_OP_STOP_DISCOVERY commands and sends proper command
status events.
This patch also fixes the MGMT_OP_STOP_DISCOVERY command leak in
case cancel inquiry fails.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch renames the function mgmt_inquiry_failed() to
mgmt_start_discovery_failed(). This function is more related
to MGMT_OP_START_DISCOVERY command handling than to inquiry.
Besides, this functions will be reused by LE based discovery
procedures in case of failure.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch removes unnecessary NULL checks noticed by Dan Carpenter.
Checks were introduced in commit
4a287eba2d to net-next.
Signed-off-by: Matti Vaittinen <Mazziesaccount@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when dev_hard_header() failed, the newly allocated skb should be freed.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The support for NLM_F_* flags at IPv6 routing requests.
If NLM_F_CREATE flag is not defined for RTM_NEWROUTE request,
warning is printed, but no error is returned. Instead new route is
added. Later NLM_F_CREATE may be required for
new route creation.
Exception is when NLM_F_REPLACE flag is given without NLM_F_CREATE, and
no matching route is found. In this case it should be safe to assume
that the request issuer is familiar with NLM_F_* flags, and does really
not want route to be created.
Specifying NLM_F_REPLACE flag will now make the kernel to search for
matching route, and replace it with new one. If no route is found and
NLM_F_CREATE is specified as well, then new route is created.
Also, specifying NLM_F_EXCL will yield returning of error if matching
route is found.
Patch created against linux-3.2-rc1
Signed-off-by: Matti Vaittinen <Mazziesaccount@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The support for NLM_F_* flags at IPv6 routing requests.
Warn if NLM_F_CREATE flag is not defined for RTM_NEWROUTE request,
creating new table. Later NLM_F_CREATE may be required for
new route creation.
Patch created against linux-3.2-rc1
Signed-off-by: Matti Vaittinen <Mazziesaccount@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the thing we discussed during netdev 2011 conference was the idea
to change some network drivers to allocate/populate their skb at RX
completion time, right before feeding the skb to network stack.
In old days, we allocated skbs when populating the RX ring.
This means bringing into cpu cache sk_buff and skb_shared_info cache
lines (since we clear/initialize them), then 'queue' skb->data to NIC.
By the time NIC fills a frame in skb->data buffer and host can process
it, cpu probably threw away the cache lines from its caches, because lot
of things happened between the allocation and final use.
So the deal would be to allocate only the data buffer for the NIC to
populate its RX ring buffer. And use build_skb() at RX completion to
attach a data buffer (now filled with an ethernet frame) to a new skb,
initialize the skb_shared_info portion, and give the hot skb to network
stack.
build_skb() is the function to allocate an skb, caller providing the
data buffer that should be attached to it. Drivers are expected to call
skb_reserve() right after build_skb() to adjust skb->data to the
Ethernet frame (usually skipping NET_SKB_PAD and NET_IP_ALIGN, but some
drivers might add a hardware provided alignment)
Data provided to build_skb() MUST have been allocated by a prior
kmalloc() call, with enough room to add SKB_DATA_ALIGN(sizeof(struct
skb_shared_info)) bytes at the end of the data without corrupting
incoming frame.
data = kmalloc(NET_SKB_PAD + NET_IP_ALIGN + 1536 +
SKB_DATA_ALIGN(sizeof(struct skb_shared_info)),
GFP_ATOMIC);
...
skb = build_skb(data);
if (!skb) {
recycle_data(data);
} else {
skb_reserve(skb, NET_SKB_PAD + NET_IP_ALIGN);
...
}
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Tom Herbert <therbert@google.com>
CC: Jamal Hadi Salim <hadi@mojatatu.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Thomas Graf <tgraf@infradead.org>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 3ceca74966 added a TOS attribute.
Unfortunately TOS and TCLASS are both present in a dual-stack v6 socket,
furthermore they can have different values. As such one cannot in a
sane way expose both through a single attribute.
Signed-off-by: Maciej Żenczyowski <maze@google.com>
CC: Murali Raja <muralira@google.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Le mercredi 09 novembre 2011 à 16:21 -0500, David Miller a écrit :
> From: David Miller <davem@davemloft.net>
> Date: Wed, 09 Nov 2011 16:16:44 -0500 (EST)
>
> > From: Eric Dumazet <eric.dumazet@gmail.com>
> > Date: Wed, 09 Nov 2011 12:14:09 +0100
> >
> >> unres_qlen is the number of frames we are able to queue per unresolved
> >> neighbour. Its default value (3) was never changed and is responsible
> >> for strange drops, especially if IP fragments are used, or multiple
> >> sessions start in parallel. Even a single tcp flow can hit this limit.
> > ...
> >
> > Ok, I've applied this, let's see what happens :-)
>
> Early answer, build fails.
>
> Please test build this patch with DECNET enabled and resubmit. The
> decnet neigh layer still refers to the removed ->queue_len member.
>
> Thanks.
Ouch, this was fixed on one machine yesterday, but not the other one I
used this morning, sorry.
[PATCH V5 net-next] neigh: new unresolved queue limits
unres_qlen is the number of frames we are able to queue per unresolved
neighbour. Its default value (3) was never changed and is responsible
for strange drops, especially if IP fragments are used, or multiple
sessions start in parallel. Even a single tcp flow can hit this limit.
$ arp -d 192.168.20.108 ; ping -c 2 -s 8000 192.168.20.108
PING 192.168.20.108 (192.168.20.108) 8000(8028) bytes of data.
8008 bytes from 192.168.20.108: icmp_seq=2 ttl=64 time=0.322 ms
Signed-off-by: David S. Miller <davem@davemloft.net>
More changes to the recent code to support control of forwarding
database via netlink.
* Support NTF_USE like neighbour table
* Validate state bits from application
* Only send notifications (and change bits) if new entry is
different.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
