This patch adds the following utils:
1. Convert slave_id -> VF
2. Get the active ports by slave_id
3. Convert slave's port to real port
4. Get the slave's port from real port
5. Get all slaves that uses the i'th real port
6. Get all slaves that uses the i'th real port exclusively
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the required data structures to support VFs with N (1 or 2)
ports instead of always using the number of physical ports.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some code in the mlx4 IB driver stack assumed MLX4_MAX_PORTS ports.
Instead, we should only loop until the number of actual ports in i
the device, which is stored in dev->caps.num_ports.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since passing the clock is not mandatory, change the warning message to debug,
so that we avoid getting the following clock failure message on every boot:
smsc911x: Driver version 2008-10-21
smsc911x smsc911x (unregistered net_device): couldn't get clock -2
libphy: smsc911x-mdio: probed
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we are out of initial debug/bringup mode, remove
the verbose dump of the mapping table.
Provide the mapping table in sysfs, under the hardware queue
directory, in the cpu_list file.
Signed-off-by: Jens Axboe <axboe@fb.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e100, igb, igbvf, ixgbe and ixgbevf.
Stefan adds a igb patch to enable the ability strip VLAN header information
for packets bound for a VM on i350 hardware.
Joe Perches provides patches for e100, igb, igbvf, ixgbe and ixgbevf to
convert the use of __constant_<foo> to just <foo> to align with the rest
of the kernel.
Don provides two fixes for ixgbe, first resolves a link issue with DA
cables where we were not always freeing the firmware/software semaphore
after grabbing it. Second stops caching whether the management firmware
was enabled, however since this is not static, we really need to verify
with each check.
Jacob provides six fixes/cleanups for ixgbe, most notably, correct
the stop_mac_link_on d3() to check the Core Clock Disable bit before
stopping link and to fully check to see if manage firmware is running or
could be enabled before bringing down the link. Fix flow control
auto-negation for KR/KX/K4 interfaces, since setting up MAC link, the
cached autoc value and current autoc value were being incorrectly used to
determine whether link reset is required.
Emil provides a fix for ixgbe where there was a chance for aggressive
start_ndo_zmit() callers to sneak packets between enabling the Tx queues
and the link coming up. To resolve this, move the call to enable Tx
queues to after the link is established.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation for how to use netlink mmap interface is incorrect.
The calls to setsockopt() require an additional argument.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MIPS fixes from Ralf Baechle:
"Another set of five fixes. The most interesting one is a fix for race
condition in the local_irq_disable() implementation used by .S code
for pre-MIPS R2 processors only. It leaves a race that's hard but not
impossible to hit; the others fairly obvious"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Make local_irq_disable macro safe for non-Mipsr2
MIPS: Octeon: Fix warning in of_device_alloc on cn3xxx
MIPS: ftrace: Tweak safe_load()/safe_store() macros
MIPS: BCM47XX: Check all (32) GPIOs when looking for a pin
MIPS: Fix possible build error with transparent hugepages enabled
Just two minor bug fixes: a fix for a regression in oxygen driver
that was introduced in 3.14-rc1, and a stable fix for the return
value of compress offload open callback.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=W9OP
-----END PGP SIGNATURE-----
Merge tag 'sound-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just two minor bug fixes: a fix for a regression in oxygen driver that
was introduced in 3.14-rc1, and a stable fix for the return value of
compress offload open callback"
* tag 'sound-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: compress: Pass through return value of open ops callback
ALSA: oxygen: Xonar DG(X): fix Stereo Upmixing regression
The kernel starts out its "jiffies" timer as 5 minutes below zero, as
shown in include/linux/jiffies.h:
/*
* Have the 32 bit jiffies value wrap 5 minutes after boot
* so jiffies wrap bugs show up earlier.
*/
#define INITIAL_JIFFIES ((unsigned long)(unsigned int) (-300*HZ))
The loop in ovs_flow_stats_get() starts out with 'used' set to 0, then
takes any "later" time. This means that for the first five minutes after
boot, flows will always be reported as never used, since 0 is greater than
any time already seen.
Signed-off-by: Ben Pfaff <blp@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Without this, the following scenario is incorrectly determined
to be invalid.
addr 0x7f_ffffe000 size 8192 addr_limit 0x80_00000000
This behavior was observed while trying to vmsplice the stack
as part of a CRIU dump of a process on a system started with the
norandmaps kernel parameter.
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In event format strings, the array size is reported in two locations.
One in array subscript and then via the "size:" attribute. The values
reported there have a mismatch.
For e.g., in sched:sched_switch the prev_comm and next_comm character
arrays have subscript values as [32] where as the actual field size is
16.
name: sched_switch
ID: 301
format:
field:unsigned short common_type; offset:0; size:2; signed:0;
field:unsigned char common_flags; offset:2; size:1; signed:0;
field:unsigned char common_preempt_count; offset:3; size:1;signed:0;
field:int common_pid; offset:4; size:4; signed:1;
field:char prev_comm[32]; offset:8; size:16; signed:1;
field:pid_t prev_pid; offset:24; size:4; signed:1;
field:int prev_prio; offset:28; size:4; signed:1;
field:long prev_state; offset:32; size:8; signed:1;
field:char next_comm[32]; offset:40; size:16; signed:1;
field:pid_t next_pid; offset:56; size:4; signed:1;
field:int next_prio; offset:60; size:4; signed:1;
After bisection, the following commit was blamed:
92edca0 tracing: Use direct field, type and system names
This commit removes the duplication of strings for field->name and
field->type assuming that all the strings passed in
__trace_define_field() are immutable. This is not true for arrays, where
the type string is created in event_storage variable and field->type for
all array fields points to event_storage.
Use __stringify() to create a string constant for the type string.
Also, get rid of event_storage and event_storage_mutex that are not
needed anymore.
also, an added benefit is that this reduces the overhead of events a bit more:
text data bss dec hex filename
8424787 2036472 1302528 11763787 b3804b vmlinux
8420814 2036408 1302528 11759750 b37086 vmlinux.patched
Link: http://lkml.kernel.org/r/1392349908-29685-1-git-send-email-vnagarnaik@google.com
Cc: Laurent Chavey <chavey@google.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Vaibhav Nagarnaik <vnagarnaik@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
We need to ensure that we do not send events to user space with the
identity address if we have not yet notified user space of the IRK. The
code was previously trying to handle this for the mgmt_pair_device
response (which worked well enough) but this is not the only connection
related event that might be sent to user space before pairing is
successful: another important event is Device Disconnected.
The issue can actually be solved more simply than the solution
previously used for mgmt_pair_device. Since we do have the identity
address tracked as part of the remote IRK struct we can just copy it
over from there to the hci_conn struct once we've for real sent the mgmt
event for the new IRK.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to support the driver behaviour introduced by:
commit d0575a5a703978c43e25128421158c78534ba100
Author: Daniel Kim <dekim@broadcom.com>
Date: Wed Mar 12 18:12:14 2014 -0700
brcmfmac: Enable 40MHz bandwidth in 2GHz band and OBSS scanning
in devices that do not support bwcap firmware command a fallback
is added.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the function brcmf_sdiod_request_data() an error message is logged,
but the calling function retries it. This patch will only log an error
message when retry limit is reached. The low-level error is still
logged by a SDIO debug message.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog thread waits on completion that is set from a timer. As
the completion is count based this could mean that on a busy system
the watchdog is handled multiple times with a very short interval.
This is not the intended behaviour. After handling the watchdog it
should wait for the next timer expiry. This is accomplished by
reinitializing the completion.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables 40MHz bandwidth in 2GHz band after checking whether
cfg80211 allows it or not, and enables OBSS scanning operations to
to support 20/40 BSS coexistence.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
linux/compat.h does not include linux/unistd.h but the compat.h header
file contains various conditional
#ifdef __ARCH_WANT_COMPAT_...
asmlinkage long compat...()
#endif
compat system call function declarations.
If linux/unistd.h isn't included it depends on previous includes if those
__ARCH_WANT_COMPAT_... defines are defined or not. So add an additional
linux/unistd.h include.
Should fix this compile error on tile:
include/uapi/asm-generic/unistd.h:195:1: error: 'compat_sys_getdents64' undeclared
make[3]: *** [arch/tile/kernel/compat.o] Error 1
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
For non-mipsr2 processors, the local_irq_disable contains an mfc0-mtc0
pair with instructions inbetween. With preemption enabled, this sequence
may get preempted and effect a stale value of CP0_STATUS when executing
the mtc0 instruction. This commit avoids this scenario by incrementing
the preempt count before the mfc0 and decrementing it after the mtc9.
[ralf@linux-mips.org: This patch is sorting out the part that were missed
by e97c5b6098 [MIPS: Make irqflags.h functions preempt-safe for non-mipsr2
cpus.] I also re-enabled the inclusion of <asm/asm-offsets.h> at the top
of <asm/asmmacro.h>].
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* pm-cpufreq: (30 commits)
intel_pstate: Set core to min P state during core offline
cpufreq: Add stop CPU callback to cpufreq_driver interface
cpufreq: Remove unnecessary braces
cpufreq: Fix checkpatch errors and warnings
cpufreq: powerpc: add cpufreq transition latency for FSL e500mc SoCs
cpufreq: remove unused notifier: CPUFREQ_{SUSPENDCHANGE|RESUMECHANGE}
cpufreq: Do not allow ->setpolicy drivers to provide ->target
cpufreq: arm_big_little: set 'physical_cluster' for each CPU
cpufreq: arm_big_little: make vexpress driver depend on bL core driver
cpufreq: SPEAr: Instantiate as platform_driver
cpufreq: Remove unnecessary variable/parameter 'frozen'
cpufreq: Remove cpufreq_generic_exit()
cpufreq: add 'freq_table' in struct cpufreq_policy
cpufreq: Reformat printk() statements
cpufreq: Tegra: Use cpufreq_generic_suspend()
cpufreq: s5pv210: Use cpufreq_generic_suspend()
cpufreq: exynos: Use cpufreq_generic_suspend()
cpufreq: Implement cpufreq_generic_suspend()
cpufreq: suspend governors on system suspend/hibernate
cpufreq: move call to __find_governor() to cpufreq_init_policy()
...
* pm-cpuidle:
cpuidle: delay enabling interrupts until all coupled CPUs leave idle
cpuidle: poll state can measure residency
cpuidle: Move perf multiplier calculation out of the selection loop
cpuidle: Do not substract exit latency from assumed sleep length
cpuidle: Ensure menu coefficients stay within domain
cpuidle: Use actual state latency in menu governor
cpuidle: rename expected_us to next_timer_us in menu governor
rjw> Why exactly are they errors?
Geert> checkpatch.pl says: "WARNING: please, no space before tabs",
Vim (with "let c_space_errors=1") shows them in red.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds support for the Cirrus Logic CS42448/CS42888 Audio CODEC that
has six/four 24-bit AD and eight 24-bit DA converters.
[ CS42448/CS42888 supports both I2C and SPI control ports. As initial patch,
this patch only adds the support for I2C. ]
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are only two users of get_nohz_timer_target(): timer and hrtimer. Both
call it under same circumstances, i.e.
#ifdef CONFIG_NO_HZ_COMMON
if (!pinned && get_sysctl_timer_migration() && idle_cpu(this_cpu))
return get_nohz_timer_target();
#endif
So, it makes more sense to get all this as part of get_nohz_timer_target()
instead of duplicating code at two places. For this another parameter is
required to be passed to this routine, pinned.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Cc: fweisbec@gmail.com
Cc: peterz@infradead.org
Link: http://lkml.kernel.org/r/1e1b53537217d58d48c2d7a222a9c3ac47d5b64c.1395140107.git.viresh.kumar@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Multitouch touchpads built for Win 8.1 need to be sent an input mode feature report
in order to start reporting multitouch events. This is the same process sent
to Win 7 multitouch touchscreens except the value of the feature report is 3 for
touchpads.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch moves the call to enable Tx queues after the link is established.
Previously there was a chance for aggressive start_ndo_xmit() callers to
sneak packets between enabling the Tx queues and the link coming up.
In addition it replaces netif_tx_start_all_queues() with
netif_tx_wake_all_queues() to allow for flushing of the qdisc.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We use to cache whether the MNG FW was enabled, how since this isn't
static we really need to verify with each check. This patch makes that
change.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rather than assign several parameters in a row, we should use a for
loop, which reduces code size.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces some direct uses of pci_read_config_word with the
protected ixgbe_read_pci_cfg_word function, which checks for whether the
adapter is removed when LER is enabled. We shouldn't use the
pci_read_config_word calls directly because of these checks.
This patch also cleans up an unnecessary save of a pointer to the mac
object, as our standard style is to just use the hw pointer.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reverts the addition of the fiber_fixed type, which ended up
never being used. We don't have plans to support this type going
forward, and there is no reason to keep an unused type around polluting
the code.
Reverts: 4e8e1bca6e ("ixgbe: add new media type")
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes flow control autonegotiation for KR/KX/K4 interfaces.
When setting up MAC link, the cached autoc value and current autoc value
were being incorrectly used to determine whether link reset is required.
This resulted in the driver ignoring and discarding flow control
negotiation changes that occur since the caching happened, as well as
when the mac was being setup.
This patch also splits the assignments for the 3 autoc variables into
their own block, and adds a comment explaining what each one means, in
order to help keep logic more straightforward while reading the code.
CC: Arun Sharma <asharma@fb.com>
Reported-by: Sourav Chatterjee <sourav.chatterjee@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a temporary fix for some Intel HDMI codecs to avoid no sound output for
a resuming playback after S3.
After S3, the audio driver restores pin:cvt connection selections by
snd_hda_codec_resume_cache(). However this can happen before the gfx side is
ready and such connect selection is overlooked by HW. After gfx is ready, the
pins make the default selection again. And this will cause multiple pins share
a same convertor and mute control will affect each other. Thus a resumed audio
playback become silent after S3.
This patch verifies pin:cvt connection on preparing a stream, to assure the pin
selects the right convetor and an assigned convertor is not shared by other
unused pins. Apply this fix-up on Haswell, Broadwell and Valleyview (Baytrail).
We need this temporary fix before a reliable software communication channel is
established between audio and gfx, to sync audio/gfx operations.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previously, we did a full check to see if MNG FW was running. Instead,
we should only check to see whether it could be enabled. Since it may
become active while down, we don't want to bring the link down.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The passkey_notify and user_confirm functions in mgmt.c were expecting
different endianess for the passkey, leading to a big endian bug and
sparse warning in recently added SMP code. This patch converts both
functions to expect host endianess and do the conversion to little
endian only when assigning to the mgmt event struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch corrects the stop_mac_link_on_d3 function in ixgbe_82599 by
checking the Core Clock Disable bit before stopping link.
CC: Arun Sharma <asharma@fb.com>
Reported-by: Chris Pavlas <chris.pavlas@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Found several incorrect conditionals after calling the prot_autoc_*
functions. Likewise we weren't always freeing the FWSW semaphore after
grabbing it. This would lead to DA cables being unable to link along with
possible other errors.
CC: Arun Sharma <asharma@fb.com>
CC: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
