Since 32k timer code is moving to OMAP1 specific dir, move the
32k-based sched_clock() into common code where it is based on the 32k
sync counter and can be used even when using MPU timer.
While moving, change the ticks-to-nsecs conversion to use the helper
functions provided by clocksource.h.
Also removed the unused ticks_to_usec, leaving only ticks_to_nsec.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP2/3, the gp-timer code can be used for a 32kHz timer simply by
setting the source to be the 32k clock instead of sys_clk.
This patch uses the mach-omap2/timer-gp.c code for 32kHz timer on
OMAP2, moving the logic into mach-omap2/timer-gp.c, and not using
plat-omap/timer32k.c which, for OMAP2, is redundant with the timer-gp
code.
Also, if CONFIG_OMAP_32K_TIMER is enabled, the gptimer-based
clocksource is not used. Instead the default 32k sync counter is used
as the clocksource (see the clocksource in plat-omap/common.c.) This
is important for sleep/suspend so there is a valid counter during
sleep. Note that the suspend/sleep code needs fixing to check for
overflows of this counter.
In addition, the OMAP2/3 details are removed from timer32k.c leaving
that with only OMAP1 specifics. A follow-up patch will move it from
plat-omap common code to mach-omap1.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use omap processor specific function depending on system type.
Based on an earlier patch by Klaus Pedersen <klaus.k.pedersen@nokia.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes pin multiplexing init to allow registering
custom function. The omap_cfg_reg() func will be split into
omap processor specific functions in later patch.
This is done to make adding omap3 pin multiplexing easier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, the GPIO interrupt handling is duplicating some of the work
done by the generic IRQ handlers (handle_edge_irq, handle_level_irq)
such as detecting nesting, handling re-triggers etc. Remove this
duplication and use generic hooks based on IRQ type.
Using generic IRQ handlers ensures correct behavior when using
threaded interrupts introduced by the -rt patch.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clearing was moved to the unmask hook because it is known to run
after the interrupt handler has actually run. Before this patch, if
interrupts are threaded, the clearing/unmasking of level triggered
interrupts would be done before the threaded handler actually ran.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OSK board to use new tps65010 gpiolib support. This
includes moving its LED support from leds-osk to gpio-leds,
giving more trigger options and a net platform code shrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Start cleaning up GPIO handling for OMAP5912 OSK board:
- Initialize GPIOs using the cross-platform calls, not the old
OMAP-private ones.
- Move touchscreen setup out of ads7846 code into board-specfic
setup code, where it belongs.
This doesn't depend on the patches to update OMAP to use the
gpiolib implementation framework.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update OMAP to use the new GPIO implementation framework. This is just a
quick'n'dirty update ... more code could now be removed, ideally as part
of cleaning up the entire OMAP GPIO infrastructure ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Correctly determine the address of an illegal instruction. The EPCR0 register
holds this value (masked by EPCR0_PC) if the validity bit is set (masked by
EPCR0_V). So the test as to whether the contents of the register are usable
should be involve checking the _V bit, not the _PC bits.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If an SLB miss interrupt happens while the RI bit of MSR is zero, we
can't just return, because RI being zero indicates that SRR0/SRR1
potentially had live values in them, and the process of taking an
interrupt overwrites them.
This should never happen, but if it does, we try to print a nice oops
message. That doesn't work, however, because the code at unrecov_slb
assumes that the MMU has been turned on, but we call it with the MMU
off (and have done so since the SLB miss handler was rewritten to run
without turning the MMU on) -- except on iSeries, where everything runs
with the MMU on.
This fixes it by adding the necessary code to turn the MMU on if
necessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is a NUMA memory configuration issue in 2.6.24:
A 2-node machine of ours has got the following memory layout:
Node 0: 0 - 2 Gbytes
Node 0: 4 - 8 Gbytes
Node 1: 8 - 16 Gbytes
Node 0: 16 - 18 Gbytes
"efi_memmap_init()" merges the three last ranges into one.
"register_active_ranges()" is called as follows:
efi_memmap_walk(register_active_ranges, NULL);
i.e. once for the 4 - 18 Gbytes range. It picks up the node
number from the start address, and registers all the memory for
the node #0.
"register_active_ranges()" should be called as follows to
make sure there is no merged address range at its entry:
efi_memmap_walk(filter_memory, register_active_ranges);
"filter_memory()" is similar to "filter_rsvd_memory()",
but the reserved memory ranges are not filtered out.
Signed-off-by: Zoltan Menyhart <Zoltan.Menyhart@bull.net>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The prevent_tail_call() macro works around the problem of the compiler
clobbering argument words on the stack, which for asmlinkage functions
is the caller's (user's) struct pt_regs. The tail/sibling-call
optimization is not the only way that the compiler can decide to use
stack argument words as scratch space, which we have to prevent.
Other optimizations can do it too.
Until we have new compiler support to make "asmlinkage" binding on the
compiler's own use of the stack argument frame, we have work around all
the manifestations of this issue that crop up.
More cases seem to be prevented by also keeping the incoming argument
variables live at the end of the function. This makes their original
stack slots attractive places to leave those variables, so the compiler
tends not clobber them for something else. It's still no guarantee, but
it handles some observed cases that prevent_tail_call() did not.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch also resolves hangs on boot:
http://lkml.org/lkml/2008/2/23/263http://bugzilla.kernel.org/show_bug.cgi?id=10093
The bug was causing once-in-few-reboots 10-15 sec wait during boot on
certain laptops.
Earlier commit 40d6a14662 added
smp_call_function in cpu_idle_wait() to kick cpus that are in tickless
idle. Looking at cpu_idle_wait code at that time, code seemed to be
over-engineered for a case which is rarely used (while changing idle
handler).
Below is a simplified version of cpu_idle_wait, which just makes a dummy
smp_call_function to all cpus, to make them come out of old idle handler
and start using the new idle handler. It eliminates code in the idle
loop to handle cpu_idle_wait.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make NOMMU-mode work with base addresses other than 0xC0000000 by:
(1) Giving the code that sets up the protection registers the right address
in __sdram_base. Rather than being hard coded to 0xC0000000, the value
of __page_offset is obtained from the linker script.
(2) Eliminate the check in __switch_to() that verifies the current thread
info is in the 0xCxxxxxxx region.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use traps 120-126 to emulate atomic cmpxchg32, xchg32, and XOR-, OR-, AND-, SUB-
and ADD-to-memory operations for userspace.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This deprecates old set/reset_scoop_gpio interfacein favour of
support for generic gpio interface.
It requires gpiolib, so it depends on the previous patch
(gpiolib for SA-1100).
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds gpiolib support for the SA-1100 arch:
- Move all GPIO API functions from generic.c into gpio.c
- Convert all gpio functions into gpiolib callbacks.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make scoop driver use generic purpose io routines: ioread16
and iowrite16 instead of direct writing to memory.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cleanup most errors errors reported by sparse:
declare IO space as __iomem,
use %p for address printing
make functions static
Use __devinit instead of __init for scoop_init
Make scoop_remove __devexit and use __devexit_p for referencing it.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Buffalo Linkstation Pro/Live is the same hardware as the
Kurobox Pro but without the NAND flash. This patch adds a
second MACHINE_START macro to the Kurobox setup file to minimise
code duplication.
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Updates the CSB637 platform's D1/PB2 LED to use gpio-led by default.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converts the D1/PB2 LED to use the gpio-leds API and heartbeat trigger.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converts the CSB637 to the new-style UART initialization API.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converts the CSB337 target to the new UART initialization API.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the default configuration for the following AT91-based boards:
Embest ATEB9200
Cogent CSB337
Cogent CSB637
Sperry-Sun KAFA
Picotux200
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the default configuration for the following AT91-based boards:
Atmel AT91RM9200 DK
Atmel AT91RM9200 EK
Atmel AT91SAM9260 EK
Atmel AT91SAM9261 EK
Atmel AT91SAM9263 EK
Atmel AT91SAM9RL EK
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1) ptrace should pass 'current' to task_user_regset_view()
2) When fetching general registers using a 64-bit view, and
the target is 32-bit, we have to convert.
3) Skip the whole register window get/set code block if
the user isn't asking to access anything in there.
Otherwise we have problems if the user doesn't have
an address space setup. Fetching ptrace register is
still valid at such a time, and ptrace does not try
to access the register window area of the regset.
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc expects all toplevel assembly to return to the original section type.
The code in alteranative.c does not do this. This caused some strange bugs
in sched-devel where code would end up in the .rodata section and when
the kernel sets the NX bit on all .rodata, the kernel would crash when
executing this code.
This patch adds a .previous marker to return the code back to the
original section.
Credit goes to Andrew Pinski for telling me it wasn't a gcc bug but a
bug in the toplevel asm code in the kernel. ;-)
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Untangle the chaos of page size determination in this function by
simply using PAGE_SIZE << compound_order().
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The functions time_before, time_before_eq, time_after, and time_after_eq are
more robust for comparing jiffies against other values.
So use the time_after() & time_before() macros, defined at linux/jiffies.h,
which deal with wrapping correctly
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: S.Caglar Onur <caglar@pardus.org.tr>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
show_mem() has no need to print the amount of free swap space manually because
show_free_areas() does this already and is called by the former.
The two outputs only differ in text formatting:
printk("Free swap = %lukB\n", ...);
printk("Free swap: %6ldkB\n", ...);
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
IA64's IOMMU implementation allocates memory areas spanning LLD's segment
boundary limit. It forces low level drivers to have a workaround to adjust
scatter lists that the IOMMU builds.
We are in the process of making all the IOMMUs respect the segment boundary
limits to remove such work around in LLDs. This patch is for IA64's IOMMU.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add kprobe-booster support on ia64.
Kprobe-booster improves the performance of kprobes by eliminating single-step,
where possible. Currently, kprobe-booster is implemented on x86 and x86-64.
This is an ia64 port.
On ia64, kprobe-booster executes a copied bundle directly, instead of single
stepping. Bundles which have B or X unit and which may cause an exception
(including break) are not executed directly. And also, to prevent hitting
break exceptions on the copied bundle, only the hindmost kprobe is executed
directly if several kprobes share a bundle and are placed in different slots.
Note: set_brl_inst() is used for preparing an instruction buffer(it does not
modify any active code), so it does not need any atomic operation.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: bibo,mao <bibo.mao@intel.com>
Cc: Rusty Lynch <rusty.lynch@intel.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The sys_getpid() and sys_set_tid_address() behavior changed from
return current->tgid
to
struct pid *pid;
pid = current->pids[PIDTYPE_PID].pid;
return pid->numbers[pid->level].nr;
But the fast system calls on ia64 still operate the old way. Patch them
appropriately to let ia64 work with pid namespaces. Besides, this is one more
step in deprecating of pid and tgid on task_struct.
The fsys_getppid() is to be patched as well, but its logic is much
more complex now, so I will make it later.
One thing I'm not 100% sure is the trick with the IA64_UPID_SHIFT. On order
to access the pid->level's element of an array I have to perform the following
calculations
pid + sizeof(struct upid) * pid->level
The problem is that ia64 can only multiply float point registers, while all
the offsets I have in code are in rXX ones. Fortunately, the sizeof(struct
upid) is 32 bytes on ia64 (and is very unlikely to ever change), so the
calculations get simpler:
pid + pid->level << 5
So, I introduce the IA64_UPID_SHIFT and use the shl instruction. I also
looked at how gcc compiles the similar place and found that it makes it with
shift as well. Is this OK to do so?
Tested with ski emulator with 2.6.24 kernel, but fits 2.6.25-rc4 and
2.6.25-rc4-mm1 as well.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: David Mosberger-Tang <davidm@hpl.hp.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Amy Griffis <amy.griffis@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
do_each_thread/while_each_thread is a double loop, so
should use 'goto' rather than 'break' to break out
the loop.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
One should normally unlock in the reverse order of the lock calls,
and in this case there certainly is no reason not to.
Signed-off-by: Alan D. Brunelle <alan.brunelle@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
While it is convenient that we can invoke kdump by asserting INIT
via button on chassis etc., there are some situations that invoking
kdump on fatal MCA is not welcomed rather than rebooting fast without
dump.
This patch adds a new flag 'kdump_on_fatal_mca' that is independent
from 'kdump_on_init' currently available. Adding this flag enable
us to turning on/off of kdump depend on the event, INIT and/or fatal
MCA. Default for this flag is to take the dump.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This attached patch significantly shrinks boot memory allocation on ia64.
It does this by not allocating per_cpu areas for cpus that can never
exist.
In the case where acpi does not have any numa node description of the
cpus, I defaulted to assigning the first 32 round-robin on the known
nodes.. For the !CONFIG_ACPI I used for_each_possible_cpu().
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
A simple fix. The existing pernodesize reservation is not taking into
account a second array of pg_data_t structures. This is normally not
important because the PAGE_ALIGN macro reserves adequate space.
I made the compute_pernodesize steps in the same order as the fill_pernode
steps to make the correlation more clear.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
flush_cache_vmap / flush_cache_vunmap were calling flush_cache_all which -
having been deprecated - turned into a nop ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In time_cpufreq_notifier() the cpu id to act upon is held in freq->cpu. Use it
instead of smp_processor_id() in the call to set_cyc2ns_scale().
This makes the preempt_*able() unnecessary and lets set_cyc2ns_scale() update
the intended cpu's cyc2ns.
Related mail/thread: http://lkml.org/lkml/2007/12/7/130
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
revert:
| commit 47001d6033
| Author: Thomas Gleixner <tglx@linutronix.de>
| Date: Tue Apr 1 19:45:18 2008 +0200
|
| x86: tsc prevent time going backwards
it has been identified to cause suspend regression - and the
commit fixes a longstanding bug that existed before 2.6.25 was
opened - so it can wait some more until the effects are better
understood.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This replaces simscsi_fillresult with scsi_sg_copy_from_buffer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix user accesses in regset code.
[SPARC64]: Fix FPU saving in 64-bit signal handling.
