x86_64 needs to use compat_sys_keyctl for 32-bit userspace rather than
calling sys_keyctl(). The latter will work in a lot of cases, thereby
hiding the issue.
Reported-by: Stephan Mueller <smueller@chronox.de>
Tested-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: keyrings@vger.kernel.org
Cc: linux-security-module@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/146961615805.14395.5581949237156769439.stgit@warthog.procyon.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On Acer Veriton machines, codec with subsystem-id 0x1b0a01b8 the port at
0x15 is configured by default as an Internal Speaker (0x90170120).
However, no physical is speaker installed on-board. This patch adds a quirk
which disables the physical connection on this pin.
BugLink: https://bugs.launchpad.net/bugs/1607647
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have a Dell AIO on which we can't adjust its speaker's volume.
The problem is it is connected to a Audio Output node without Amp-out
capability. To fix it, we change it to be connnected to a node with
Amp-out capability.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are KSZ8721 PHYs with phy_id 0x00221619. In order to detect them
as PHY_ID_KSZ8001 compatible while staying different to PHY_ID_KSZ9021
ignore the last two bits when matching PHY_ID
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chunhao Lin says:
====================
r8169: fix 3 runtime pm related issues.
v2:
use "struct device *d = &tp->pci_dev->dev" instead of "struct pci_dev *pdev = tp->pci_dev"
v1:
This series of patches fix 3 runtime pm related issues that are listed below.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is no AC power, NIC may not work after changing mac address.
Please refer to following link.
http://www.spinics.net/lists/netdev/msg356572.html
This issue is caused by runtime power management. When there is no AC
power, if we put NIC down (ifconfig down), the driver will be in runtime
suspend state and hardware will be put into D3 state. During this time,
driver cannot access hardware regisers. So if you set new mac address
during this time, it will not be set to hardware. After resume, NIC will
keep using the old mac address and the network will not work normally.
In this patch I add detecting runtime pm status when setting mac address.
If driver is in runtime suspend state, it will skip setting mac address, keep
the new mac address, and set the new mac address during runtime resume.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not to call rtl8169_update_counters() to dump tally counter when driver
is in runtime suspend state.
Calling rtl8169_update_counters() in runtime suspend state will produce
warning message "rtl_counters_cond == 1 (loop: 1000, delay: 10)".
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC will be put into D3 state during runtime suspend state. When set or
get hardware wol setting, driver will write or read hardware registers.
If we set or get hardware wol setting in runtime suspend state, because
NIC will in D3 state, the hardware registers read by driver will return all
0xff. That will let driver thinking register flag is not toggled and
then prints the warning message "rtl_counters_cond == 1 (loop: 1000,
delay: 10)" to kernel log.
For fixing this issue, add checking driver's pm runtime status in
rtl8169_get_wol() and rtl8169_set_wol().
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- A couple of changes to improve the support for erase/discard/trim cmds
- Add eMMC HS400 enhanced strobe support
- Show OCR and DSR registers in SYSFS for MMC/SD cards
- Correct and improve busy detection logic for MMC switch (CMD6) cmds
- Disable HPI cmds for certain broken Hynix eMMC cards
- Allow MMC hosts to specify non-support for SD and MMC cmds
- Some minor additional fixes
MMC host:
- sdhci: Re-works, fixes and clean-ups
- sdhci: Add HW auto re-tuning support
- sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
- sdhci-esdhc-imx: Fixes and clean-ups
- sdhci-esdhc-imx: Update system PM support
- sdhci-esdhc-imx: Enable HW auto re-tuning
- sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
- sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
- sdhci-msm: Add support for UHS cards
- sdhci-tegra: Improve support for UHS cards
- sdhci-of-arasan: Update phy support for Rockchip SoCs
- sdhci-of-arasan: Deploy enhanced strobe support
- dw_mmc: Some fixes and clean-ups
- dw_mmc: Enable support for erase/discard/trim cmds
- dw_mmc: Enable CMD23 support
- mediatek: Some fixes related to the eMMC HS400 support
- sh_mmcif: Improve support for HW busy detection
- rtsx_pci: Enable support for erase/discard/trim cmds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wzSC
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- A couple of changes to improve the support for erase/discard/trim cmds
- Add eMMC HS400 enhanced strobe support
- Show OCR and DSR registers in SYSFS for MMC/SD cards
- Correct and improve busy detection logic for MMC switch (CMD6) cmds
- Disable HPI cmds for certain broken Hynix eMMC cards
- Allow MMC hosts to specify non-support for SD and MMC cmds
- Some minor additional fixes
MMC host:
- sdhci: Re-works, fixes and clean-ups
- sdhci: Add HW auto re-tuning support
- sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
- sdhci-esdhc-imx: Fixes and clean-ups
- sdhci-esdhc-imx: Update system PM support
- sdhci-esdhc-imx: Enable HW auto re-tuning
- sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
- sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
- sdhci-msm: Add support for UHS cards
- sdhci-tegra: Improve support for UHS cards
- sdhci-of-arasan: Update phy support for Rockchip SoCs
- sdhci-of-arasan: Deploy enhanced strobe support
- dw_mmc: Some fixes and clean-ups
- dw_mmc: Enable support for erase/discard/trim cmds
- dw_mmc: Enable CMD23 support
- mediatek: Some fixes related to the eMMC HS400 support
- sh_mmcif: Improve support for HW busy detection
- rtsx_pci: Enable support for erase/discard/trim cmds"
* tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc: (135 commits)
mmc: rtsx_pci: Remove deprecated create_singlethread_workqueue
mmc: rtsx_pci: Enable MMC_CAP_ERASE to allow erase/discard/trim requests
mmc: rtsx_pci: Use the provided busy timeout from the mmc core
mmc: sdhci-pltfm: Drop define for SDHCI_PLTFM_PMOPS
mmc: sdhci-pltfm: Convert to use the SET_SYSTEM_SLEEP_PM_OPS
mmc: sdhci-pltfm: Make sdhci_pltfm_suspend|resume() static
mmc: sdhci-esdhc-imx: Use common sdhci_suspend|resume_host()
mmc: sdhci-esdhc-imx: Assign system PM ops within #ifdef CONFIG_PM_SLEEP
mmc: sdhci-sirf: Remove non needed #ifdef CONFIG_PM* for dev_pm_ops
mmc: sdhci-s3c: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
mmc: sdhci-pxav3: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
mmc: sdhci-of-esdhc: Simplify code by using SIMPLE_DEV_PM_OPS
mmc: sdhci-acpi: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
mmc: sdhci-pci-core: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
mmc: Change the max discard sectors and erase response when HW busy detect
phy: rockchip-emmc: Wait even longer for the DLL to lock
phy: rockchip-emmc: Be tolerant to card clock of 0 in power on
mmc: sdhci-of-arasan: Revert: Always power the PHY off/on when clock changes
mmc: sdhci-msm: Add support for UHS cards
mmc: sdhci-msm: Add set_uhs_signaling() implementation
...
Pull watchdog updates from Wim Van Sebroeck:
"Core:
- min and max timeout improvements, WDOG_HW_RUNNING improvements,
status funtionality
- Add a device managed API for watchdog_register_device()
New watchdog drivers:
- Aspeed SoCs
- Maxim PMIC MAX77620
- Amlogic Meson GXBB SoC
Enhancements:
- support for the r8a7796 watchdog device
- support for F81866 watchdog device
- support for 5th variation of Apollo Lake
- support for MCP78S chipset
- clean-up of softdog.c watchdog device driver
- pic32-wdt and pic32-dmt fixes
- Documentation/watchdog: watchdog-test improvements
- several other fixes and improvements"
* git://www.linux-watchdog.org/linux-watchdog: (50 commits)
watchdog: gpio_wdt: Fix missing platform_set_drvdata() in gpio_wdt_probe()
watchdog: core: Clear WDOG_HW_RUNNING before calling the stop function
watchdog: core: Fix error handling of watchdog_dev_init()
watchdog: pic32-wdt: Fix return value check in pic32_wdt_drv_probe()
watchdog: pic32-dmt: Remove .owner field for driver
watchdog: pic32-wdt: Remove .owner field for driver
watchdog: renesas-wdt: Add support for the r8a7796 wdt
Documentation/watchdog: check return value for magic close
watchdog: sbsa: Drop status function
watchdog: Implement status function in watchdog core
watchdog: tangox: Set max_hw_heartbeat_ms instead of max_timeout
watchdog: change watchdog_need_worker logic
watchdog: add support for MCP78S chipset in nv_tco
watchdog: bcm2835_wdt: remove redundant ->set_timeout callback
watchdog: bcm2835_wdt: constify _ops and _info structures
dt-bindings: watchdog: Add Meson GXBB Watchdog bindings
watchdog: Add Meson GXBB Watchdog Driver
watchdog: qcom: configure BARK time in addition to BITE time
watchdog: qcom: add option for standalone watchdog not in timer block
watchdog: qcom: update device tree bindings
...
Pull btrfs updates from Chris Mason:
"This pull is dedicated to Josef's enospc rework, which we've been
testing for a few releases now. It fixes some early enospc problems
and is dramatically faster.
This also includes an updated fix for the delalloc accounting that
happens after a fault in copy_from_user. My patch in v4.7 was almost
but not quite enough"
* 'for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix delalloc accounting after copy_from_user faults
Btrfs: avoid deadlocks during reservations in btrfs_truncate_block
Btrfs: use FLUSH_LIMIT for relocation in reserve_metadata_bytes
Btrfs: fill relocation block rsv after allocation
Btrfs: always use trans->block_rsv for orphans
Btrfs: change how we calculate the global block rsv
Btrfs: use root when checking need_async_flush
Btrfs: don't bother kicking async if there's nothing to reclaim
Btrfs: fix release reserved extents trace points
Btrfs: add fsid to some tracepoints
Btrfs: add tracepoints for flush events
Btrfs: fix delalloc reservation amount tracepoint
Btrfs: trace pinned extents
Btrfs: introduce ticketed enospc infrastructure
Btrfs: add tracepoint for adding block groups
Btrfs: warn_on for unaccounted spaces
Btrfs: change delayed reservation fallback behavior
Btrfs: always reserve metadata for delalloc extents
Btrfs: fix callers of btrfs_block_rsv_migrate
Btrfs: add bytes_readonly to the spaceinfo at once
This patch enables support for Performance monitor registers related
ELF core note NT_PPC_PMU based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding one new register sets REGSET_PMU in powerpc
corresponding to the ELF core note sections added in this
regard. It also implements the get, set and active functions
for this new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for EBB state registers related
ELF core note NT_PPC_EBB based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding one new register sets REGSET_EBB in powerpc
corresponding to the ELF core note sections added in this
regard. It also implements the get, set and active functions
for this new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for running TAR, PPR, DSCR registers
related ELF core notes NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR based
ptrace requests through PTRACE_GETREGSET, PTRACE_SETREGSET calls.
This is achieved through adding three new register sets REGSET_TAR,
REGSET_PPR, REGSET_DSCR in powerpc corresponding to the ELF core
note sections added in this regad. It implements the get, set and
active functions for all these new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for all three TM checkpointed SPR
states related ELF core note NT_PPC_TM_CTAR, NT_PPC_TM_CPPR,
NT_PPC_TM_CDSCR based ptrace requests through PTRACE_GETREGSET,
PTRACE_SETREGSET calls. This is achieved through adding three
new register sets REGSET_TM_CTAR, REGSET_TM_CPPR and
REGSET_TM_CDSCR in powerpc corresponding to the ELF core note
sections added. It implements the get, set and active functions
for all these new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM SPR state related ELF core
note NT_PPC_TM_SPR based ptrace requests through PTRACE_GETREGSET,
PTRACE_SETREGSET calls. This is achieved through adding a register
set REGSET_TM_SPR in powerpc corresponding to the ELF core note
section added. It implements the get, set and active functions for
this new register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed VSX register
set ELF core note NT_PPC_CVSX based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CVSX in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed VMX register
set ELF core note NT_PPC_CVMX based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CVMX in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed FPR register
set ELF core note NT_PPC_CFPR based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CFPR in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed GPR register
set ELF core note NT_PPC_CGPR based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CGPR in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch splits gpr32_get, gpr32_set functions to accommodate
in transaction ptrace requests implemented in patches later in
the series.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables in transaction NT_PPC_VSX ptrace requests. The
function vsr_get which gets the running value of all VSX registers
and the function vsr_set which sets the running value of of all VSX
registers work on the running set of VMX registers whose location
will be different if transaction is active. This patch makes these
functions adapt to situations when the transaction is active.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables in transaction NT_PPC_VMX ptrace requests. The
function vr_get which gets the running value of all VMX registers
and the function vr_set which sets the running value of of all VMX
registers work on the running set of VMX registers whose location
will be different if transaction is active. This patch makes these
functions adapt to situations when the transaction is active.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables in transaction NT_PRFPREG ptrace requests.
The function fpr_get which gets the running value of all FPR
registers and the function fpr_set which sets the running
value of of all FPR registers work on the running set of FPR
registers whose location will be different if transaction is
active. This patch makes these functions adapt to situations
when the transaction is active.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch creates a function flush_tmregs_to_thread which
will then be used by subsequent patches in this series. The
function checks for self tracing ptrace interface attempts
while in the TM context and logs appropriate warning message.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds twelve ELF core note sections for powerpc
architecture for various registers and register sets which
need to be accessed from ptrace interface and then gdb.
These additions include special purpose registers like TAR,
PPR, DSCR, TM running and checkpointed state for various
register sets, EBB related register set, performance monitor
register set etc. Addition of these new ELF core note
sections extends the existing ELF ABI on powerpc arch without
affecting it in any manner.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This should be same as flush_tlb_page except for hash32. For hash32
I guess the existing code is wrong, because we don't seem to be
flushing tlb for Hash != 0 case at all. Fix this by switching to
calling flush_tlb_page() which does the right thing by flushing
tlb for both hash and nohash case with hash32
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some archs like ppc64 need to do special things when flushing tlb for
hugepage. Add a new helper to flush hugetlb tlb range. This helps us to
avoid flushing the entire tlb mapping for the pid.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use the helper instead of open coding the same at multiple place
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of flushing the entire mm, implement a flush_pmd_tlb_range
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use flush_hugetlb_page instead of flush_tlb_page when we clear flush the
pte.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Replace opencoding of the same at multiple places with the helper.
No functional change with this patch.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we track page size in mmu_gather, we can use address based
tlbie format when doing a tlb_flush(). We don't do this if we are
invalidating the full address space.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a comment to the generated assembler for jump labels. This makes it
easier to identify them in asm listings (generated with $ make foo.s).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This allows us to catch incorrect usage of cpu_has_feature() and
mmu_has_feature() prior to jump labels being initialised.
mpe: Use printk() and dump_stack() rather than WARN_ON(), because
WARN_ON() may not work this early in boot. Rename the Kconfig.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As we just did for CPU features.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We do binary patching of asm code using CPU features, which is a
one-time operation, done during early boot. However checks of CPU
features in C code are currently done at run time, even though the set
of CPU features can never change after boot.
We can optimise this by using jump labels to implement cpu_has_feature(),
meaning checks in C code are binary patched into a single nop or branch.
For a C sequence along the lines of:
if (cpu_has_feature(FOO))
return 2;
The generated code before is roughly:
ld r9,-27640(r2)
ld r9,0(r9)
lwz r9,32(r9)
cmpwi cr7,r9,0
bge cr7, 1f
li r3,2
blr
1: ...
After (true):
nop
li r3,2
blr
After (false):
b 1f
li r3,2
blr
1: ...
mpe: Rename MAX_CPU_FEATURES as we already have a #define with that
name, and define it simply as a constant, rather than doing tricks with
sizeof and NULL pointers. Rename the array to cpu_feature_keys. Use the
kconfig we added to guard it. Add BUILD_BUG_ON() if the feature is not a
compile time constant. Rewrite the change log.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a kconfig option to control whether we use jump label for the
cpu/mmu_has_feature() checks. Currently this does nothing, but we will
enabled it in the subsequent patches.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We plan to use jump label for cpu_has_feature(). In order to implement
this we need to include the linux/jump_label.h in asm/cputable.h.
Unfortunately if we do that it leads to an include loop. The root of the
problem seems to be that reg.h needs cputable.h (for CPU_FTRs), and then
cputable.h via jump_label.h eventually pulls in hw_irq.h which needs
reg.h (for MSR_EE).
So move cpu_has_feature() to a separate file on its own.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Rename to cpu_has_feature.h and flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This function is only used by get_vtb(). They are almost the same except
the reading from the real register. Move the mfspr() to get_vtb() and
kill the function mfvtb(). With this, we can eliminate the use of
cpu_has_feature() in very core header file like reg.h. This is a
preparation for the use of jump label for cpu_has_feature().
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Call jump_label_init() early so that we can use static keys for CPU and
MMU feature checks.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some arches (powerpc at least) would like to invoke jump_label_init()
much earlier in boot. So check static_key_initialized in order to make
sure this function runs only once.
LGTM-by: Ingo (http://marc.info/?l=linux-kernel&m=144049104329961&w=2)
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This switches early feature checks to use the non static key variant of
the function. In later patches we will be switching cpu_has_feature()
and mmu_has_feature() to use static keys and we can use them only after
static key/jump label is initialized. Any check for feature before jump
label init should be done using this new helper.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In later patches, we will be switching CPU and MMU feature checks to
use static keys.
For checks in early boot before jump label is initialized we need a
variant of [cpu|mmu]_has_feature() that doesn't use jump labels.
So create those called, unimaginatively, early_[cpu|mmu]_has_feature().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we have radix_enabled() three times, twice in asm/book3s/64/mmu.h
and then a fallback in asm/mmu.h.
Consolidate them in asm/mmu.h. While we're at it convert them to be
static inlines, and change the fallback case to returning a bool, like
mmu_has_feature().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The intention is that the result is only used as a boolean, so enforce
that by changing the return type to bool.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The intention is that the result is only used as a boolean, so enforce
that by changing the return type to bool.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
