Impact: cleanup
In asm/signal.h moved out do_notify_resume from __i386__ as it is common
for both 32 and 64 bit.
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/include/asm/signal.h | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
Impact: cleanup
In asm/system.h moved out __switch_to from CONFIG_X86_32 as it is common for
both 32 and 64 bit.
In asm/pctl.h defined sys_arch_prctl
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reward non-stop TSCs with good TSC-based clocksources, etc.
Add support for CPUID_0x80000007_Bit8 on Intel CPUs as well. This bit means
that the TSC is invariant with C/P/T states and always runs at constant
frequency.
With Intel CPUs, we have 3 classes
* CPUs where TSC runs at constant rate and does not stop n C-states
* CPUs where TSC runs at constant rate, but will stop in deep C-states
* CPUs where TSC rate will vary based on P/T-states and TSC will stop in deep
C-states.
To cover these 3, one feature bit (CONSTANT_TSC) is not enough. So, add a
second bit (NONSTOP_TSC). CONSTANT_TSC indicates that the TSC runs at
constant frequency irrespective of P/T-states, and NONSTOP_TSC indicates
that TSC does not stop in deep C-states.
CPUID_0x8000000_Bit8 indicates both these feature bit can be set.
We still have CONSTANT_TSC _set_ and NONSTOP_TSC _not_set_ on some older Intel
CPUs, based on model checks. We can use TSC on such CPUs for time, as long as
those CPUs do not support/enter deep C-states.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: add new synthetic-cpuid bit definition
add X86_FEATURE_NONSTOP_TSC to the cpufeature bits - this is in
preparation of Venki's always-running-TSC patch.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A bug in the fusion driver was exposed by the switch to block timeout.
Basically, drivers are supposed to terminate commands once error
handling begins on them. The fusion apparently wasn't doing this.
Under the old timeout regime, completions on terminated commands would
by and large get ignored because of the way command timeouts used to
work. The new block timers are very intolerant to this, though,
becuase the request gets cleaned and freed.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=12195
Reported-by: Alex Shi <alex.shi@intel.com>
Tested-by: Ming Lin <ming.m.lin@intel.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Impact: remove dead/incorrect code
Currently there is no chipset specific ucode. The checks are incorrect
anyway (e.g. pci device IDs are 16 bit and not 8 bit).
Thus I remove the stuff for the time being and will reintroduce it if
it's foreseeable that it is really needed.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix build warning
CC arch/x86/kernel/microcode_amd.o
arch/x86/kernel/microcode_amd.c: In function ‘request_microcode_fw’:
arch/x86/kernel/microcode_amd.c:393: warning: passing argument 2 of ‘generic_load_microcode’ discards qualifiers from pointer target type
(Respect "const" qualifier of firmware->data.)
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix bug resulting in non-loaded AMD microcode
mc_header->processor_rev_id is a 2 byte value. Similar is true for
equiv_cpu in an equiv_cpu_entry -- only 2 bytes are of interest.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The v4l_compat_ioctl32() function only tested for the presence of the
ioctl op, not for unlocked_ioctl. So it would always return an error
when used with drivers that use unlocked_ioctl instead of ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the tuner modules were moved to common/tuners, a separate customize
option were added for tuners. However, the automatic selection of the
tuners were still using the older option.
This causes that the automatic selection to fail, if DVB_FE_CUSTOMISE is
selected. Also, since those tuners are now under MEDIA_TUNER_CUSTOMIZE
menu, if you unset MEDIA_TUNER_CUSTOMIZE, you can't manually select the
tuners.
This patch fixes this error by replacing DVB_FE_CUSTOMISE by
MEDIA_TUNER_CUSTOMIZE on all places were a tuner is selected.
The patch were generated by this small script:
for i in `find drivers/media -name Kconfig`; do
cat $i|perl -ne 's/(MEDIA_TUNER.*)DVB_FE_CUSTOMISE/\1MEDIA_TUNER_CUSTOMIZE/; print $_' >a
mv a $i
done
Also, manually reordered the tuner entries.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At some point the Flexcop driver was changed to support newer Flexcop cards.
These modifications however broke the detection of Cablestar 2 DVB-C cards.
The reason is that the earlier version of the driver used to retry
unsuccessful i2c operations. The demodulator of Cablestar 2 cards (stv0297)
seems to be very dependent on these retries and adding them back fixes
Cablestar detection.
This patch restores this behaviour for the CableStar2.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A user noticed that there would continue to be 4-6 keypresses even after the
user stopped holding down the button. This was because we were not reading
the bulk pipe faster than the firmware was injecting information, which would
result in a backlog.
Make the query interval faster, and increase the number of cycles before we
start repeating to compensate.
Thanks to Knud Poulsen <knud.poulsen@nokia.com> for pointing this out.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
on 64-bit x86 the physical memory limit is controlled by the sparsemem
bits - which are 44 bits right now. But MAXMEM (the max pfn number
e820 parsing will allow to enter our sizing routines) is set to
0x00003fffffffffff, i.e. 46 bits - that's too large because it overlaps
into the vmalloc range.
So couple MAXMEM to MAX_PHYSMEM_BITS, and add a comment that the
maximum of MAX_PHYSMEM_BITS is 45 bits.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'sh/for-2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Disable GENERIC_HARDIRQS_NO__DO_IRQ for unconverted platforms.
sh: maple: Do not pass SLAB_POISON to kmem_cache_create()
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc/cell/axon-msi: Fix MSI after kexec
powerpc: Fix bootmem reservation on uninitialized node
powerpc: Check for valid hugepage size in hugetlb_get_unmapped_area
Some of the inconsistencies checked for at run time can be detected at
build time already, so duplicate the checks done at run time to also be
done at build time.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Neither of the callers really needs the physical address this function
returns, so eliminate the pointless argument.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reduce bug table size
This allows reducing the bug table size by half. Perhaps there are
other 64-bit architectures that could also make use of this.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, code robustization
The __swp_...() macros silently relied upon which bits are used for
_PAGE_FILE and _PAGE_PROTNONE. After having changed _PAGE_PROTNONE in
our Xen kernel to no longer overlap _PAGE_PAT, live locks and crashes
were reported that could have been avoided if these macros properly
used the symbolic constants. Since, as pointed out earlier, for Xen
Dom0 support mainline likewise will need to eliminate the conflict
between _PAGE_PAT and _PAGE_PROTNONE, this patch does all the necessary
adjustments, plus it introduces a mechanism to check consistency
between MAX_SWAPFILES_SHIFT and the actual encoding macros.
This also fixes a latent bug in that x86-64 used a 6-bit mask in
__swp_type(), and if MAX_SWAPFILES_SHIFT was increased beyond 5 in (the
seemingly unrelated) linux/swap.h, this would have resulted in a
collision with _PAGE_FILE.
Non-PAE 32-bit code gets similarly adjusted for its pte_to_pgoff() and
pgoff_to_pte() calculations.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: change the reporting of empty BTS records
Correctly report a cleared BTS record as invalid. Used to be reported
as branch from 0 to 0.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Optimistically allocate a DS context. It is extremely unlikely that
one already existed. This simplifies the code a lot.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 80bba1290a removed one necessary
variable initialization. As a result following warning happened:
CC mm/migrate.o
mm/migrate.c: In function 'sys_move_pages':
mm/migrate.c:1001: warning: 'err' may be used uninitialized in this function
More unfortunately, if find_vma() failed, kernel read uninitialized
memory.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
CC: Brice Goglin <Brice.Goglin@inria.fr>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes an inconsistency that became apparent when I
documented the fields of snd_ca0106_details. spi_dac is always
used in a 'boolean' sense, so this cleanup should make no difference.
[Actually, there is one place checking explicitly spi_dac == 1, so
this will change the behavior. But, supposing it's rather a typo,
I apply this clean-up patch -- tiwai]
Signed-off-by: Ben Stanley <Ben.Stanley@exemail.com.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi wrote an email [1] explaining the fields of snd_ca0106_details,
so I captured the information into the ca0106.h header file.
[1] http://article.gmane.org/gmane.linux.alsa.devel/56783/match=takashi+gpio_type
Signed-off-by: Ben Stanley <Ben.Stanley@exemail.com.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch export per-cpu CPU cycle usage for a given cpuacct cgroup.
There is a need for a user space monitor daemon to track group CPU
usage on per-cpu base. It is also useful for monitoring CFS load
balancer behavior by tracking per CPU group usage.
Signed-off-by: Ken Chen <kenchen@google.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: micro-optimize the code on 64-bit architectures
In the thread regarding to 'export percpu cpuacct cgroup stats'
http://lkml.org/lkml/2008/12/7/13
akpm pointed out that current cpuacct code is inefficient. This patch
refactoring the following:
* make cpu_rq locking only on 32-bit
* change iterator to each_present_cpu instead of each_possible_cpu to
make it hotplug friendly.
It's a bit of code churn, but I was rewarded with 160 byte code size saving
on x86-64 arch and zero code size change on i386.
Signed-off-by: Ken Chen <kenchen@google.com>
Cc: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
IDE hpt366 driver doesn't allow DMA for ATAPI devices and MWDMA2 on
ATAPI device locks up pata_hpt366. Follow the suit.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_hpt366 is strange in that its two channels occupy two PCI
functions and both are primary channels and bit1 of PCI configuration
register 0x5A indicates cable for both channels.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Due to miscommunication, P/N was mistaken as firmware revision
strings. Update it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
1.When no interface is specified in an IPV6_PKTINFO ancillary data
item, the interface specified in an IPV6_PKTINFO sticky optionis
is used.
RFC3542:
6.7. Summary of Outgoing Interface Selection
This document and [RFC-3493] specify various methods that affect the
selection of the packet's outgoing interface. This subsection
summarizes the ordering among those in order to ensure deterministic
behavior.
For a given outgoing packet on a given socket, the outgoing interface
is determined in the following order:
1. if an interface is specified in an IPV6_PKTINFO ancillary data
item, the interface is used.
2. otherwise, if an interface is specified in an IPV6_PKTINFO sticky
option, the interface is used.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When get receiving interface index while no message is received,
the the value seted with setsockopt() should be returned.
RFC 3542:
Issuing getsockopt() for the above options will return the sticky
option value i.e., the value set with setsockopt(). If no sticky
option value has been set getsockopt() will return the following
values:
- For the IPV6_PKTINFO option, it will return an in6_pktinfo
structure with ipi6_addr being in6addr_any and ipi6_ifindex being
zero.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are three reasons for me to add this support:
1.When no interface is specified in an IPV6_PKTINFO ancillary data
item, the interface specified in an IPV6_PKTINFO sticky optionis
is used.
RFC3542:
6.7. Summary of Outgoing Interface Selection
This document and [RFC-3493] specify various methods that affect the
selection of the packet's outgoing interface. This subsection
summarizes the ordering among those in order to ensure deterministic
behavior.
For a given outgoing packet on a given socket, the outgoing interface
is determined in the following order:
1. if an interface is specified in an IPV6_PKTINFO ancillary data
item, the interface is used.
2. otherwise, if an interface is specified in an IPV6_PKTINFO sticky
option, the interface is used.
2.When no IPV6_PKTINFO ancillary data is received,getsockopt() should
return the sticky option value which set with setsockopt().
RFC 3542:
Issuing getsockopt() for the above options will return the sticky
option value i.e., the value set with setsockopt(). If no sticky
option value has been set getsockopt() will return the following
values:
3.Make the setsockopt implementation POSIX compliant.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These 4 drivers have identical full duplex flow control resolution
functions. This patch changes them all to use one common function.
The function in question decides whether a device should enable TX and
RX flow control in a standard way (IEEE 802.3-2005 table 28B-3), so this
should also be useful for other drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
