The member "clock" of struct "sja1000_platform_data" is documented as
"CAN bus oscillator frequency in Hz" but it's actually used as the CAN
clock frequency, which is half of it. To avoid further confusion, this
patch fixes it by renaming the member to "osc_freq". That way, also
non mainline users will notice the change. The platform code for the
relevant boards is updated accordingly. Furthermore, pre-defined
values are now used for the members "ocr" and "cdr".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb rxhash should be cleared when a skb is handled by a tunnel before
being delivered again, so that correct packet steering can take place.
There are other cleanups and accounting that we can factorize in a new
helper, skb_tunnel_rx()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 33ad798c92 (tcp: options clean up) introduced a problem
if MD5+SACK+timestamps were used in initial SYN message.
Some stacks (old linux for example) try to negotiate MD5+SACK+TSTAMP
sessions, but since 40 bytes of tcp options space are not enough to
store all the bits needed, we chose to disable timestamps in this case.
We send a SYN-ACK _without_ timestamp option, but socket has timestamps
enabled and all further outgoing messages contain a TS block, all with
the initial timestamp of the remote peer.
Fix is to really disable timestamps option for the whole session.
Reported-by: Bijay Singh <Bijay.Singh@guavus.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The duplicate address check code got broken in the conversion
to hlist (2.6.35). The earlier patch did not fix the case where
two addresses match same hash value. Use two exit paths,
rather than depending on state of loop variables (from macro).
Based on earlier fix by Shan Wei.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves ADC device definition to plat-samsung.
Because that is generic to the S3C64XX and S5P Series SoCs.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Especially when IR needs to do polling, it generates lots of wakeups per
second. This makes no sense, if the input event device is closed.
Adds a callback handler to the IR hardware driver, to allow registering
an open/close ops.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
IR is an alias for Infrared Remote, while RC is an alias for Remote
Controller.
While currently all implementations are with Infrared Remote Controller,
this subsystem is not meant to be used only by IR type of RC's. So,
as discussed on both linux-media and linux-input, the better is to
rename the subsystem as Remote Controller.
While, currently, the only application that uses the /sys/class/irrcv is
ir-keytable application, and its sysfs support works only with the
current linux-next code, it is still possible to change the userspace API
without the risk of breaking applications. So, better to rename this
sooner than later.
Later patches will be needed to rename the files and to move them away
from drivers/media, but this is not a critical issue. So, for now,
let's just change the name of the sysfs class/nodes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the help of raw_register/raw_unregister, adds a sysfs group
associated with the decoder, inside the corresponding irrcv node.
Writing 1 to nec_decoder/enabled enables the decoder, while
writing 0 disables it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some decoders and a lirc_dev interface may need some other operations to work.
For example: IR device register/unregister and ir_keydown events may need to
be tracked.
As some operations can occur in interrupt time, and a lock is needed to prevent
un-registering a decode while decoding a key, the lock needed to be convert
into a spin lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of hardcoding the protocols into ir-core, add a register interface
for the IR protocol decoders, and convert ir-nec-decoder into a client of
ir-core.
With this approach, it is possible to dynamically load the needed IR protocols,
and to add a RAW IR interface module, registered as one IR raw protocol decoder.
This patch opens a way to register a lirc_dev interface to work as an userspace
IR protocol decoder.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At raw_decode mode, the key is processed after the end of a timer. The
previous code resets the timer every time something is received at the IR
port. While this works fine with IR's that don't implement repeat, like
Avermedia RM-JX IR, it keeps waiting until keydown, on IR's that implement
NEC repeat command, like the Terratec yellow.
The solution is to change the behaviour to do the timeout after the first
received data.
The timeout is currently set to 15 ms, as it works fine with NEC protcocol.
It may need some adjustments to support other protocols and to better handle
spurious detections that may happen with some IR sensors.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds a method to pass IR raw pulse/code events into ir-core. This is
needed in order to support LIRC. It also helps to move common code
from the drivers into the core.
In order to allow testing, it implements a simple NEC protocol decoder
at ir-nec-decoder.c file. The logic is about the same used at saa7134
driver that handles Avermedia M135A and Encore FM53 boards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2 specification requires drivers to use the write events in the
file operations poll handler for output devices. The uvcvideo driver
erroneously used read events for all devices. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those control, as their names imply, control the camera aperture
settings.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera requires the STREAM_NO_FID quirk. Add a corresponding entry
in the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera requires the PROBE_DEF quirk. Add a corresponding entry in
the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some webcams handled by both sn9c102 or zc0301 and some gspca subdrivers
(sonixb, sonixj and zc3xx) were not handled when gspca was generated but
not the associated subdrivers.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the sequence streamon -> streamoff and again s_input, it fails
to lock the signal, since streamoff puts TVP514x into power off state
which leads to failure in sub-sequent s_input.
So add powerup sequence in s_routing (if disabled), since it is
important to lock the signal at this stage.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Muralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the devices like AM3517, it is expected that driver clears the
interrupt in ISR. Since this is device spcific, callback function
added to the platform_data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Muralidharan Karicheri <mkaricheri@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Converted this old V4L1 driver to V4L2.
I would like to thank Takeo Takahashi who very kindly tested this
driver for me. Much appreciated!
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Tested-by: Takeo Takahashi <takahashi.takeo@renesas.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of completely unnecessary function prototypes.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Old 4 and 6 bit greyscale pixel formats for the old bw-qcam webcam.
This is needed to convert it to V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clean up the coding style before we convert this driver to V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clean up the coding style before we convert this driver to V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clean up the coding style before we convert this driver to V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clean up the coding style before we convert this driver to V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of some "unused variable" warnings. These were the result of
sloppiness and should not have happened; I'll go stand in the corner now.
Reported-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That makes frame rate configuration persistent.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Cafe controller doesn't do non-SMBUS I/O, so we have to use it there.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow applications to play with the gain settings.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
