This is intended to support named (with a handle, etc) objects having
children that don't have an outside reference.
This will replace the various hacks around the place where subdev
objects have children, and have to manually drop the self-refs so
that they can be destroyed etc when all the outside refs have gone.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We need to be able to process interrupts before the DRM code is able to
actually enable them, set it up ourselves. Also, it's less convoluted
to *not* use the DRM wrappers it appears...
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It'd be pretty awesome if someone would care enough to port this all
properly to a class interface, perhaps submitting a command stream to
the core via a sw object on PFIFO (emulating how EVO works basically,
and also what nvidia have done forever..)..
But, this seems unlikely given how old this hardware is now, so, lets
just hide it away.
There's a heap of other bits and pieces laying around that are still
tangled. I'll (re)move them in pieces.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Seen in the wild, don't have the hardware but this hacks things up to
treat it the same as GF119 for now.
Should be relatively safe, I'd be very surprised if anything major
changed outside of PGRAPH. PGRAPH (3D etc) is disabled by default
however until it's confirmed working.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
v2: read, don't assume.. *puts on brown paper bag*
Signed-off-by: Roy Spliet <r.spliet@student.tudelft.nl>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This patch adds support for the backlight control of the NVIDIA GT
525M, which identifies itself as a member of the NVC0 family.
v2. Extended to handle Kepler too
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Compression not supported, and will be silently dropped. Original G80
can't handle this either and requires LINEAR memtype, though it's still
possible to correctly texture and m2mf to/from these objects anyway.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not sure about the (gpc_nr == 1) condition, it's probably wrong but for
all the examples I've seen so far it matches what NVIDIA end up poking.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is needed because temperature management on nv50 can be enabled and it
looks about the same as nv40.
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It's probably impossible to hit it now on mainline kernel.
I only noticed it because one of my debugging patches uses it.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Commit fc9bbca8f6 (vm: convert fb_mmap to
vm_iomap_memory() helper) made fbmem.c use vm_iomap_memory, but also
accidentally removed the check for mmio's availability.
Add the check back.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Improve fb_mmap bounds checks in gbefb, smscufx, udlfb and vfb drivers to
prevent possible uint overflows.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Bernie Thompson <bernie@plugable.com>
Use vm_iomap_memory() instead of [io_]remap_pfn_range().
vm_iomap_memory() gives us much simpler API to map memory to userspace,
and reduces possibilities for bugs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
This patch adds the mac type to the version in ethtool_regs.
This will make it easier to check the mac type when dumping registers with
ethtool. The drawback of this is that older versions of ethtool will only
be able to dump in hex format for 82599 and above when used with the updated
driver.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for disabling link during boot time. This
feature was requested by customers and is configurable through the EEPROM.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes majority of the AUTOC register reads by using a cached
value instead.
The reason for this change is to avoid writing corrupted values to AUTOC
due to bad FW.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the logic in ixgbe_setup_loopback_test() to only access
registers applicable to the MAC type. AUTOC is only valid on MACs older than
X540. MACC is used for X540.
In addition it removes a read of AUTOC and uses the stored value to force the
link up.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the ixgbe_msix_other was writing the full 32bits of the set
interrupts, instead of only the ones which the ixgbe_msix_other is
handling. This resulted in a loss of performance when the X540's PPS feature is
enabled due to sometimes clearing queue interrupts which resulted in the driver
not getting the interrupt for cleaning the q_vector rings often enough. The fix
is to simply mask the lower 16bits off so that this handler does not write them
in the EICR, which causes them to remain high and be properly handled by the
clean_rings interrupt routine as normal.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If you really want 100000us you should really use mdelay or so.
Found by the LTO kernel build
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
An "unable to handle kernel paging request" panic can occur when receiving
traffic while the interface is going down. Wait for NAPI to be done with
current context after disabling interrupts and then disable NAPI.
See https://bugzilla.vyatta.com/show_bug.cgi?id=8837.
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PTP Hardware Clock settime function in the e1000e driver
computes nanoseconds from a struct timespec. The code converts the
seconds field .tv_sec by multiplying it with NSEC_PER_SEC. However,
both operands are of type long, resulting in an unintended overflow.
The patch fixes the issue by using the helper function from time.h.
CC: stable <stable@vger.kernel.org>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
drm_match_cea_mode() should be able to match both the 60Hz version,
and the 59.94Hz version of modes.
We only store one pixel clock value per mode in edid_cea_modes, so the
other value must be calculated. Depending on the mode, edid_cea_modes
contains the pixel clock for either the 60Hz version or the 59.94Hz
version, so a bit of care is needed so that the calculation produces
the correct result.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=46800
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Well have use for the vrefresh information of CEA modes later. Just
populate the information into the table to avoid having to calculate
it.
I'm too lazy to check if someone relies on newly allocated CEA
modes having 0 vrefresh, so just clear vrefresh back to 0 when
adding the mode to the connector's modelist.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_mode_equal_no_clocks() is like drm_mode_equal() except it doesn't
compare the clock or vrefresh values. drm_mode_equal() is now
implemented by first doing the clock checks, and then calling
drm_mode_equal_no_clocks().
v2: Add missing EXPORT_SYMBOL()
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
