Both __d_unalias() and __d_materialise_dentry() need loop prevention.
Grab rename_lock in caller, check for loops there...
As a side benefit, we have dentry_lock_for_move() called only under
rename_lock, which seriously reduces deadlock potential of the
execrable "locking order" used for ->d_lock.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix the condition where PS3 network RX hangs when no network
TX is occurring by calling gelic_card_enable_rxdmac() during
RX_DMA_CHAIN_END event processing.
The gelic hardware automatically clears its RX_DMA_EN flag when
it detects an RX_DMA_CHAIN_END event. In its processing of
RX_DMA_CHAIN_END the gelic driver is required to set RX_DMA_EN
(with a call to gelic_card_enable_rxdmac()) to restart RX DMA
transfers. The existing gelic driver code does not set
RX_DMA_EN directly in its processing of the RX_DMA_CHAIN_END
event, but uses a flag variable card->rx_dma_restart_required
to schedule the setting of RX_DMA_EN until next inside the
interrupt handler.
It seems this delayed setting of RX_DMA_EN causes the hang since
the next RX interrupt after the RX_DMA_CHAIN_END event where
RX_DMA_EN is scheduled to be set will not occur since RX_DMA_EN
was not set. In the case were network TX is occuring, RX_DMA_EN
is set in the next TX interrupt and RX processing continues.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overview:
Support mapping of priorities to traffic classes and
traffic classes to transmission queues ranges in the net device.
The queue ranges are (count, offset) pairs relating to the txq
array.
This can be done via DCBX negotiation or by kernel.
As a result Enhanced Transmission Selection (ETS) and Priority Flow
Control (PFC) are supported between L2 network traffic classes.
Mapping:
This patch uses the netdev_set_num_tc, netdev_set_prio_tc_map and
netdev_set_tc_queue functions to map priorities to traffic classes
and traffic classes to transmission queue ranges.
This mapping is performed by bnx2x_setup_tc function which is
connected to the ndo_setup_tc.
This function is always called at nic load where by default it
maps all priorities to tc 0, and it may also be called by the
kernel or by the bnx2x upon DCBX negotiation to modify the mapping.
rtnl lock:
When the ndo_setup_tc is called at nic load or by kernel the rtnl
lock is already taken. However, when DCBX negotiation takes place
the lock is not taken. The work is therefore scheduled to be
handled by the sp_rtnl task.
Fastpath:
The fastpath structure of the bnx2x which was previously used
to hold the information of one tx queue and one rx queue was
redesigned to represent multiple tx queues, one for each traffic
class.
The transmission queue supplied in the skb by the kernel can no
longer be interpreted as a straightforward index into the fastpath
structure array, but it must rather be decoded to the appropriate
fastpath index and the tc within that fastpath.
Slowpath:
The bnx2x's queue object was redesigned to accommodate multiple
transmission queues. The queue object's state machine was enhanced
to allow opening multiple transmission-only connections on top of
the regular tx-rx connection.
Firmware:
This feature relies on the tx-only queue feature introduced in the
bnx2x 7.0.23 firmware and the FW likewise must have the bnx2x multi
cos support.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming the "reset_task" to a more general purpose name,
"sp_rtnl_task", as it is already used for another purpose
other than reset which is parity recovery, and since I
plan to add a third operation for this task, updating the
priority to traffic class and traffic class to transmission
queues mappings after dcbx negotiation takes place.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no software fallback implemented for SCTP or FCoE checksumming,
and so it should not be passed on by software devices like bridge or bonding.
For VLAN devices, this is different. First, the driver for underlying device
should be prepared to get offloaded packets even when the feature is disabled
(especially if it advertises it in vlan_features). Second, devices under
VLANs do not get replaced without tearing down the VLAN first.
This fixes a mess I accidentally introduced while converting bonding to
ndo_fix_features.
NETIF_F_SOFT_FEATURES are removed from BOND_VLAN_FEATURES because they
are unused as of commit 712ae51afd.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets to devices without NETIF_F_SCTP_CSUM (including NETIF_F_NO_CSUM)
should be properly checksummed because the packets can be diverted or
rerouted after construction. This still leaves packets diverted from
NETIF_F_SCTP_CSUM-enabled devices with broken checksums. Fixing this
needs implementing software offload fallback in networking core.
For users of sctp_checksum_disable, skb->ip_summed should be left as
CHECKSUM_NONE and not CHECKSUM_UNNECESSARY as per include/linux/skbuff.h.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove it, as it indirectly exposes netdev features. It's not used in
iproute2 (2.6.38) - is anything else using its interface?
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same information and more can be obtained by using ethtool
with ETHTOOL_GFEATURES.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not used anywhere except net/core/dev.c now.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_features contains features inherited from underlying device.
NETIF_SOFT_FEATURES are not inherited but belong to the vlan device
itself (ensured in vlan_dev_fix_features()).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the fact that ORing with zero is a no-op.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove wrong setting of dev->flags. NETIF_F_NO_CSUM maps to IFF_DEBUG
there, so looks like a mistake.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the init value before reset in probe function. And then just
modify the relative bits and keep the init settings.
For 8110S, 8110SB, and 8110SC series, the initial value of RxConfig
needs to be set after the tx/rx is enabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Only 8111b needs to enable rx when shutdowning with WoL.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Only 8111E needs enable RxConfig bit 0 ~ 3 when suspending or
shutdowning for wake on lan.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Add the ERI functions which would be used by the new chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
- Disable tx and rx by resetting hw, so replace rtl8169_asic_down
with rtl8169_hw_reset.
- RxConfig bits 0 ~ 5 have to be cleared before hw reset to avoid
receiving spurious data.
- Certain chips need to do some checking before reset.
- Remove hw reset which is done before hw_start. It is done in close,
down or device probe functions.
- Move rtl8169_init_ring_indexes function into rtl_hw_reset function.
The indexes of tx and rx only need to be zero when the hw resets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: Resolve inode eviction and ail list interaction bug
GFS2: Fix race during filesystem mount
GFS2: force a log flush when invalidating the rindex glock
Reset card->tx_dma_progress when lv1_net_start_tx_dma() fails or it
won't send anything afterwards anymore
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert to a proper state when gelic_card_kick_txdma() fails:
- Don't trigger BUG_ON when releasing the unsent tx descriptor
- Reset the tx chain head since the tail was not modified and
hence not in sync
- Unlink the released descriptor bus address from its predecessor
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Change FW dump capture mask to a defult value, instead of using the recommended
value from the FW. This was done to keep the capture mask consistent with other
function drivers.
o Update driver version to 5.0.21
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Defined error code such as fw not responding, test already running and
cable not connected.
o Check Fw capability before performing loopback test.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as skb is given to hardware, TX completion can free skb under us.
Therefore, we should update dev stats before kicking the device.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC learning is required in bridge mode.
During bridge mode device will be put in promiscous mode.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added QME8242-k 10GbE Dual Port Mezzanine Card to supported card info.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip reset logic (IDC logic) has changed with fw dump support.
This broked compatibility with driver using older IDC logic.
Changes to make it compatible with drivers using older IDC logic.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scratchpad location that we were reading from has not been
initialized yet during ->probe(), so we were getting inaccurate
information.
Update version to 2.1.10.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to help debug issues related to management firmware.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to allow iSCSI connection to fail faster instead of waiting for the
long timeout.
Update version to 2.5.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest bnx2x driver uses different CID for the iSCSI rings, so
we need to pass it in the ring init data. The rx ring is also
zeroed out to prevent stale DMA addresses from being used after
shutdown.
The same cp local variable redefined inside the else branch is
also eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CHIP_2_PORT_MODE was not set correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested by Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the driver state (and power source) is being more intensely
scrutinized, we need to make sure it is correct 100% of the time. This
patch finds and fixes all dangling power state transitions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to update the status of the function to a common
location to the critical section added in the previous patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that performs the power source switching will need to consider
the status of the other devices before making any switches. The status
updates and power source switching will need to be an atomic operation,
so a critical section will be needed. This patch establishes the
critical section through a CPMU mutex.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 devices will need to know exactly what function number they are so
that they can communicate their status to the other functions. In a KVM
environment, the function number of a device presented by the kernel
might not be the true function number, so an alternative method to
determine the function number is needed.
This patch used to contain an implementation for the alternative method,
but recently we discovered a hardware bug that renders it incorrect.
While new method is not yet known, it is still useful to consolidate the
code that determines the PCI function to one location and use the
results throughout the code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently pci_set_power_state() does not return useful return codes for
transitions to the D0 power state. If a device refuses to go into D0,
the PCI layer issues a warning but returns success.
Entering into D0 is a requirement for correct operation of tg3 devices
though. If the PCI layer should be changed to return an error code for
this type of failure, the tg3 driver would be interested in catching it
and reacting to it. This patch makes the necessary modifications.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver is going to require memory mapped register access much
sooner than before. This patch makes sure the device is in the D0 power
state as soon as possible, and moves the code that enables the memory
arbiter outside tg3_get_eeprom_hw_cfg() where it can be more easily
monitored.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch will require the driver to communicate with the APE
much sooner than before. This patch make sure the APE registers are
memory mapped and that the ENABLE_APE bit is set before the first use.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we flush tp_status and then flush the remainder of the header+payload.
tp_status should be flushed in the end to avoid stale data being read by user-space.
Incorrectly re-ordered barriers in v1.
Signed-off-by: Chetan Loke <loke.chetan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is a one-to-one correspondance between neighbour
and hh_cache entries, we no longer need:
1) dynamic allocation
2) attachment to dst->hh
3) refcounting
Initialization of the hh_cache entry is indicated by hh_len
being non-zero, and such initialization is always done with
the neighbour's lock held as a writer.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains a few misc fixes which resolve a recently
reported issue. This patch has been a real team effort and has
received a lot of testing.
The first issue is that the ail lock needs to be held over a few
more operations. The lock thats added into gfs2_releasepage() may
possibly be a candidate for replacing with RCU at some future
point, but at this stage we've gone for the obvious fix.
The second issue is that gfs2_write_inode() can end up calling
a glock recursively when called from gfs2_evict_inode() via the
syncing code, so it needs a guard added.
The third issue is that we either need to not truncate the metadata
pages of inodes which have zero link count, but which we cannot
deallocate due to them still being in use by other nodes, or we need
to ensure that those pages have all made it through the journal and
ail lists first. This patch takes the former approach, but the
latter has also been tested and there is nothing to choose between
them performance-wise. So again, we could revise that decision
in the future.
Also, the inode eviction process is now better documented.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Tested-by: Bob Peterson <rpeterso@redhat.com>
Tested-by: Abhijith Das <adas@redhat.com>
Reported-by: Barry J. Marson <bmarson@redhat.com>
Reported-by: David Teigland <teigland@redhat.com>
Commit 28c2103 added new state ACPI_STATE_D3_COLD, so the device power
states array must be expanded by one also.
v2: Use ACPI_D_STATE_COUNT instead of number 5 for the array size.
Reported-by: Dan Carpenter <error27@gmail.com>
Suggested-by: Oldřich Jedlička <oldium.pro@seznam.cz>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
