Updates to u-boot allow this board to boot off of either
the 8MB soldered on flash, or the 64MB SODIMM flash.
This is achieved by changing JP12 and SW2.8 which in turn
swaps which flash device appears on /CS0 and /CS6 respectively.
Since the flash devices are not the same size, this also
changes the MTD memory map layout on the local bus.
Here we split the common chunks out into a pre and post
include, so they can be reused by an upcoming "alternative
boot" dts file; leaving only the local bus chunk behind.
No content changes are made at this point - it is just purely
the move to using include files.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use for_each_compatible_node() macro instead of open coding it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When the guest triggers an alignment interrupt, we don't handle it properly
today and instead BUG_ON(). This really shouldn't happen.
Instead, we should just pass the interrupt back into the guest so it can deal
with it.
Reported-by: Gao Guanhua-B22826 <B22826@freescale.com>
Tested-by: Gao Guanhua-B22826 <B22826@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Current kvmppc_booke_handlers uses the same macro (KVM_HANDLER) and
all handlers are considered to be the same size. This will not be
the case if we want to use different macros for different handlers.
This patch improves the kvmppc_booke_handler so that it can
support different macros for different handlers.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
[bharat.bhushan@freescale.com: Substantial changes]
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Like other places, use thread_struct to get vcpu reference.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
arch/powerpc/sysdev/fsl_msi.c:31:1: warning: symbol 'msi_head' was not declared. Should it be static?
arch/powerpc/sysdev/fsl_msi.c:138:40: warning: incorrect type in argument 1 (different base types)
arch/powerpc/sysdev/fsl_msi.c:138:40: expected restricted __be64 const [usertype] *p
arch/powerpc/sysdev/fsl_msi.c:138:40: got unsigned long long const [usertype] *[assigned] reg
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/sysdev/fsl_lbc.c:77:36: warning: incorrect type in initializer (different base types)
arch/powerpc/sysdev/fsl_lbc.c:77:36: expected restricted __be32 [usertype] br
arch/powerpc/sysdev/fsl_lbc.c:77:36: got unsigned int
arch/powerpc/sysdev/fsl_lbc.c:78:36: warning: incorrect type in initializer (different base types)
arch/powerpc/sysdev/fsl_lbc.c:78:36: expected restricted __be32 [usertype] or
arch/powerpc/sysdev/fsl_lbc.c:78:36: got unsigned int
arch/powerpc/sysdev/fsl_lbc.c:80:21: warning: restricted __be32 degrades to integer
arch/powerpc/sysdev/fsl_lbc.c:80:38: warning: restricted __be32 degrades to integer
arch/powerpc/sysdev/fsl_lbc.c:111:12: warning: incorrect type in assignment (different base types)
arch/powerpc/sysdev/fsl_lbc.c:111:12: expected restricted __be32 [usertype] br
arch/powerpc/sysdev/fsl_lbc.c:111:12: got unsigned int
arch/powerpc/sysdev/fsl_lbc.c:113:17: warning: restricted __be32 degrades to integer
arch/powerpc/sysdev/fsl_lbc.c:127:17: warning: restricted __be32 degrades to integer
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The DTC labels feature allows a dts file to reference a node without
having to reproduce the entire node hierarchy above it. We can use this
to simplify the MPC5200 board dts files by referencing the gpt nodes by
label.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[agust: fixed gpt7 phandle in the csi node of o2d.dtsi]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The Lite5200 evaluation board has a number of debug LEDs that Linux
doesn't know about yet. This change adds a gpio-leds stanza to the
lite5200 device tree so that the correct driver can get hooked up.
Also, make use of the dtc labels feature to reduce the number of source
lines required to add the gpio-controller property to the general
purpose timer nodes. In addition, the required #gpio-cells properties
are added to the common mpc5200b dtsi include file so that each board
doesn't need to add them explicitly. This still doesn't enable gpio
mode, 'gpio-controller' is required for that, but it means less work
needs to be done by board ports.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix PowerPC/Cell build fallout from:
8bd75c77b7 sched/rt: Move rt specific bits into new header file
Reported-by: Michael Ellerman <michael@ellerman.id.au>
Cc: Clark Williams <williams@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20130207094707.7b9f825f@riff.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Synchronize with 'net' in order to sort out some l2tp, wireless, and
ipv6 GRE fixes that will be built on top of in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for enabling and context switching the Target
Address Register in Power8. The TAR is a new special purpose register
that can be used for computed branches with the bctar[l] (branch
conditional to TAR) instruction in the same manner as the count and link
registers.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pseries/iommu: remove DDW on kexec
We currently insert a property in the device-tree when we successfully
configure DDW for a given slot. This was meant to be an optimization to
speed up kexec/kdump, so that we don't need to make the RTAS calls again
to re-configured DDW in the new kernel.
However, we end up tripping a plpar_tce_stuff failure on kexec/kdump
because we unconditionally parse the ibm,dma-window property for the
node at bus/dev setup time. This property contains the 32-bit DMA window
LIOBN, which is distinct from the DDW window's. We pass that LIOBN (via
iommu_table_init -> iommu_table_clear -> tce_free ->
tce_freemulti_pSeriesLP) to plpar_tce_stuff, which fails because that
32-bit window is no longer present after
25ebc45b93 ("powerpc/pseries/iommu: remove
default window before attempting DDW manipulation").
I believe the simplest, easiest-to-maintain fix is to just change our
initcall to, rather than detecting and updating the new kernel's DDW
knowledge, just remove all DDW configurations. When the drivers
re-initialize, we will set everything back up as it was before.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The parameter is unused, and complicates a following fix. Just remove
it.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It seems, we're fine with just annotating the two functions.
Thus, this fixes the following build warnings on ppc64:
WARNING: arch/powerpc/sysdev/xics/built-in.o(.text+0x1664):
The function .ics_rtas_init() references
the function __init .xics_register_ics().
This is often because .ics_rtas_init lacks a __init
annotation or the annotation of .xics_register_ics is wrong.
WARNING: arch/powerpc/sysdev/built-in.o(.text+0x6044):
The function .ics_rtas_init() references
the function __init .xics_register_ics().
This is often because .ics_rtas_init lacks a __init
annotation or the annotation of .xics_register_ics is wrong.
WARNING: arch/powerpc/kernel/built-in.o(.text+0x2db30):
The function .start_secondary() references
the function __cpuinit .vdso_getcpu_init().
This is often because .start_secondary lacks a __cpuinit
annotation or the annotation of .vdso_getcpu_init is wrong.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Bestcomm driver requests a memory region larger than the one
described in the device tree. This is due to an extra undocumented field
in the bestcomm register structure. This hasn't been a problem up to
now, but there is a patch pending to make the DT platform_bus support
code use platform_device_add() which tightens the rules and provides
extra checks for drivers to stay within the specified register regions.
Alternately, I could have removed the extra field from the structure,
but I'm not sure if it is still needed for resume to work. Better be
safe and leave it in.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Anatolij Gustschin <agust@denx.de>
Fix warnings:
symbol 'clockctl' was not declared. Should it be static?
symbol 'rate_clks' was not declared. Should it be static?
symbol 'dev_clks' was not declared. Should it be static?
symbol 'mpc5121_clk_init' was not declared. Should it be static?
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add ability to configure chip select (CS) parameters for devices
that need different CS parameters setup after their configuration.
I.e. an FPGA device on LP bus can require different CS parameters
for its bus interface after loading firmware into it. A driver
can easily reconfigure the LPC CS parameters using this function.
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The IRQ_PER_CPU Kconfig symbol was removed in the following commit:
Commit 6a58fb3bad ("genirq: Remove
CONFIG_IRQ_PER_CPU") merged in v2.6.39-rc1.
But IRQ_PER_CPU wasn't removed from any of the architecture Kconfig
files where it was defined or selected. It's completely unused so remove
the remaining references.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: <uclinux-dist-devel@blackfin.uclinux.org>
Cc: <linux-mips@linux-mips.org>
Cc: <linuxppc-dev@lists.ozlabs.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Richard Kuo <rkuo@codeaurora.org>
Link: http://lkml.kernel.org/r/1359972583-17134-1-git-send-email-james.hogan@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ASM version of hash computation function was truncating the upper bit.
Make the ASM version similar to hpt_hash function. Remove masking vsid bits.
Without this patch, we observed hang during bootup due to not satisfying page
fault request correctly. The fault handler used wrong hash values to update
the HPTE. Hence we kept looping with page fault.
hash_page(ea=000001003e260008, access=203, trap=300 ip=3fff91787134 dsisr 42000000
The computed value of hash 000000000f22f390
update: avpnv=4003e46054003e00, hash=000000000722f390, f=80000006, psize: 2 ...
BenH: The over-masking has been there for ever but only hurts with the
new 64T support introduced in 3.7
Reported-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Tested-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.7]
Only alpha and sparc are unusual - they have ka_restorer in it.
And nobody needs that exposed to userland.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Switch from __ARCH_WANT_SYS_RT_SIGACTION to opposite
(!CONFIG_ODD_RT_SIGACTION); the only two architectures that
need it are alpha and sparc. The reason for use of CONFIG_...
instead of __ARCH_... is that it's needed only kernel-side
and doing it that way avoids a mess with include order on many
architectures.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make some POWER7-specific perf events available in sysfs.
$ /bin/ls -1 /sys/bus/event_source/devices/cpu/events/
branch-instructions
branch-misses
cache-misses
cache-references
cpu-cycles
instructions
PM_BRU_FIN
PM_BRU_MPRED
PM_CMPLU_STALL
PM_CYC
PM_GCT_NOSLOT_CYC
PM_INST_CMPL
PM_LD_MISS_L1
PM_LD_REF_L1
stalled-cycles-backend
stalled-cycles-frontend
where the 'PM_*' events are POWER specific and the others are the
generic events.
This will enable users to specify these events with their symbolic
names rather than with their raw code.
perf stat -e 'cpu/PM_CYC' ...
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20130123062528.GE13720@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Make the generic perf events in POWER7 available via sysfs.
$ ls /sys/bus/event_source/devices/cpu/events
branch-instructions
branch-misses
cache-misses
cache-references
cpu-cycles
instructions
stalled-cycles-backend
stalled-cycles-frontend
$ cat /sys/bus/event_source/devices/cpu/events/cache-misses
event=0x400f0
This patch is based on commits that implement this functionality on x86.
Eg:
commit a47473939d
Author: Jiri Olsa <jolsa@redhat.com>
Date: Wed Oct 10 14:53:11 2012 +0200
perf/x86: Make hardware event translations available in sysfs
Changelog:[v2]
[Jiri Osla] Drop EVENT_ID() macro since it is only used once.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20130123062454.GD13720@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Define and use macros to identify perf events codes This would make it
easier and more readable when these event codes need to be used in more
than one place.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20130123062353.GB13720@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Early driver probing can fail due to not available clocks
(clk_get() fails) since the clk API init didn't take place yet.
Move clocks init before bus probing.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
There are now two kinds of DMA windows that might be presented by
PowerVM DDW support -- huge windows (that can map all of system memory
regardless of the LPAR configuration) and non-huge windows (which
can't). They are implemented slightly differently in PowerVM, and thus
have different characteristics. The most obvious is that slot isolate
doesn't clear the TCEs/window for us with non-huge windows. Thus, when a
DLPAR operation occurs on a slot using a non-huge window, TCEs are still
present (the notifier chain doesn't currently remove them explicitly)
and the DLPAR fails. Fix this by calling remove_ddw() first, which will
unmap the DDW TCEs.
Note: a corresponding change to drmgr is needed to actually successfully
DLPAR, such that the device-tree update (which causes the notifier chain
to fire) occurs before slot isolate.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
tce_clearrange_multi_pSeriesLP is attempting to iterate over all TCEs in
a given range. However, is it not advancing the dma_offset value passed
to plpar_tce_stuff via the next value. This prevents DLPAR from
completing, because TCEs are still present at slot isolation time.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change the hardware breakpoint code so that we can support wider ranged
breakpoints.
This means both ptrace and perf hardware breakpoints can use upto 512 byte long
breakpoints when using the DAWR and only 8 byte when using the DABR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we set the length field in the DAWR to 0 which defaults it to one
double word (64bits) which is the same as the DABR.
Change this so that we can set it to longer values as supported by the DAWR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
