Add dtsi for imx6q and imx6dl with non-common blocks moved into there.
Major differences between imx6dl and imx6q:
* Dual vs. Quad cores
* single vs. dual IPU
* 128 vs. 256 KB OCRAM
* imx6q: ECSPI5, OpenVG (GC355), SATA
* imx6dl: I2C4, PXP, EPDC, LCDIF
* iomuxc/pads definition
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
i.MX6 Quad and i.MX6 DualLite is similar enough to share one dtsi
file, so rename imx6q.dtsi to imx6qdl.dtsi preparing for the addition
of imx6dl support.
Another member of i.MX6 series i.MX6 SoloLite is different enough
from the other two, so it will stand as a separate dtsi. That's why
we rename to imx6qdl.dtsi not imx6.dtsi.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
For ANATOP LDOs, vddcpu, vddsoc and vddpu
have step time settings in the misc2 register, need
to add necessary step time info for these three LDOs,
then regulator driver can add necessary delay based on
these settings.
offset 0x170:
bit [24-25]: vddcpu
bit [26-27]: vddpu
bit [28-29]: vddsoc
field definition:
0'b00: 64 cycles of 24M clock;
0'b01: 128 cycles of 24M clock;
0'b02: 256 cycles of 24M clock;
0'b03: 512 cycles of 24M clock;
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Update operating-points per hardware document and add support for
1 GHz and 1.2 GHz frequencies.
400 MHz, 800 MHz and 1 GHz should be supported by all i.MX6Q chips,
while 1.2 GHz support needs to know from OTP fuse bit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Remove silicon version from SDMA firmware.
This makes it consistent with other i.MX SoCs firmware names.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The MBa53 is a baseboard for the TQMA53 embedded module. This enables/adds only
supported devices, i.e. it is not feature complete, because of missing drivers
in mainline linux.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The tqma53 is an embedded module that has some features on board (e.g. emmc),
but mostly just provides access to them on its interface.
Going along with the imx53.dtsi, the tqma53.dtsi specifies the existing
devices and their pinctrl for this module. All devices that are not on the
module are disabled by default and need to be enabled in a baseboard DT.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add pinctrl for cspi, csi.
Add new pingroups for can1 and uart3.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The keypad is on the accessory board of i.MX51 babbage
main board and is driven by Keypad Port(KPP) in SoC.
The keymap is the same to i.MX25 3stack platform as
the accessory board schematic tells that it is designed
in this way.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Just to keep consistency with other dts files, place 'status' entry as the last
one.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Following omap3-evm.dts way, it changes all imx dts files to use label
in board dts to refer to nodes defined by soc dtsi. Thus, the board
dts files become easier to read and edit with the least indentation
levels.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add missing imx dtb targets, so that make dtbs can cover all imx dtbs.
It's pretty useful for testing dts changes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add an entry for imx27-pdk.dtb, so that it can be generated by default.
Also, add an entry into Documentation/devicetree/bindings/arm/fsl.txt.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx27-pdk is the name found on Freescale website, so use it instead of 3ds.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- Mostly cfa100xx related device tree source updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJREKBFAAoJEFBXWFqHsHzOdVwH/2x2a0mJi9Y/mE0y5ZSn/Ktj
bYIOJt4wjq15/rYcSzCrZtJ+u4+JwP7C06z0oTtNeiIw2kHuAiUTVrTBdaf60k4f
2FauaoX9koedCsBP2JPVAq5ZVE8BdAbj4inuoNUFJeN/pkH8Q5+PWQZbgxAYeN58
X//DUXPq8L2tNWdEl/F+DIYwH/y9ck01tV2Fyy6AItjEShStOCglootmmtzXoyj0
/8bOmc2ppdePofAd+M/5B+JE5S18WbakrdfNp8qVwBlYzjsUvFgz9Vwkbn81jPzJ
5Hx/vDiZFktqMuI6726DJ/oqxP0w+GqYzw657LdIKqS3zCbLGb752iaM/vPgo0c=
=SM0I
-----END PGP SIGNATURE-----
Merge tag 'mxs-dt-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
mxs device tree changes for 3.9
- Mostly cfa100xx related device tree source updates
* tag 'mxs-dt-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: dts: Add rotary encoder to the CFA-10049
ARM: mxs: dts: Add gpio-keys for the rotary to the CFA-10049
ARM: dts: mxs: Add the LCD to the 10049 board
ARM: dts: mxs: Add muxing options for the third PWM
ARM: dts: cfa10049: Change the SPI3 bus to spi-gpio
ARM: mxs: dt: Add Crystalfontz CFA-10037 device tree support
ARM: mxs: Enable touchscreen on m28evk
ARM: dts: cfa10049: Add PCA9555 GPIO expander to the device tree
This pull request adds support for I2C0 and watchdog timer
for DA850 EVM booting using device tree. It also enables
machine reboot when using device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJRFoKmAAoJEGFBu2jqvgRN0PMP/jRz7la56By25SrTx0mf8RLt
MY8KqLEipoVSATEv5W/SzE7Py1PKQXKFERU6JB14/JwU/+68NfPYfWcRPJ5Ya7/a
vDM7QTSllOjAPRFjpviUD4E5PRz7HV6odYb9l/lKMXhAV7+0X/I14T6k4gEd/3pw
TdhcLRQpPyCr8HKBfnw3n0fHtWo5Zt5J7wze66vL13CIHtPaoIAY7UUN/KggSum6
mHZ3G/Po+iQjkaRyTl0O/sTTkNA3CCp9bVb7v0DXHs6Im283jdVaPX9s5HsuN7Jw
mzs3VTtS1E7is/WJbywy8ry2pjMJozJdRDWYse7wDGzTgCteQsJrQ3+C1H68IvPN
+Phb4NZhrU8clnYtMvCIENiUsK7jNrRbzDPEGLEQa/Z5apqHLFbtWa/Qx88aqALg
QdQsMgG92ZThIJ+LNaLj4fvHH9xnJjYBvYMiaKSwiTWs0b+zILQG+9Dfo8eFpQj+
PgXIhYW5Cg7CP3AqVyS6E2VSV36HCo0pSZ6aaBW6wvoCXDkOEHbxi0NpgvCWCIXK
svKGDbrSqsHnnAJz8xfeuuqpU30YqOAtScfdjfdSTUXVyOSzRD5Tb0bCK4YCpyqm
gCFWRx9y3BlP7AT4RYKKH+JJgkUEmAX7MO0EOIwk9FzxapE3dbNAcV51NoffAILl
M/jfDPHuPZLiG3zBfa+0
=d1si
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.9/dt-2' of git://gitorious.org/linux-davinci/linux-davinci into next/dt
From Sekhar Nori:
Second round of DT updates for DaVinci.
This pull request adds support for I2C0 and watchdog timer
for DA850 EVM booting using device tree. It also enables
machine reboot when using device tree.
* tag 'davinci-for-v3.9/dt-2' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: da850 DT: add support for machine reboot
ARM: davinci: da850: add wdt DT node
ARM: davinci: da850: add DT node for I2C0
- adding the watchdog to Animeo IP board
- some more DT support for at91rm9200 peripherals
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRE8zDAAoJEAf03oE53VmQOXIH/0btL+h2tiV6lY4he090YLTL
SNBbs1m05SvtfMfei1P9sFKokc5IEbf36izd1E30hcLw1bcsUulS9CChyXu4KEc2
Xd6LLIOyH4jLl2/s0rZz1lhxCoFIv9bFp0xaZgtuasUxxlsV5Kg9iee4jYIeHL4G
cX+z8qLgTpL77Ep6HBzc2K1ALXqW/0sjo+5eHwUJDHiM/+awPD3lJMnJjDKLdY8j
0BoODOuHFGTo3fdIeEprJhPTiqZMEFDfOPsLYA2ksPqZEw5LV+ITAnHiw8V5LbBI
XNP8gYTUWLv3LJqnKc9qt/6KjHUsztbtcjsSdOGmZp5IbFQw9AJGg/mBBTpEvJM=
=6yzB
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
Update to DT files for AT91:
- adding the watchdog to Animeo IP board
- some more DT support for at91rm9200 peripherals
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: add EMAC bindings to RM9200 DT
ARM: at91: add SSC bindings to RM9200 DT
ARM: at91: add MMC bindings to RM9200 DT
ARM: at91: Animeo IP: enable watchdog support
Signed-off-by: Olof Johansson <olof@lixom.net>
Add I2C0 device tree and pin muxing information to da850-evm.
Also, add OF_DEV_AUXDATA for I2C0 controller driver in da850
board dt file to use I2C0 clock.
Verified i2c0 node gets created in sys class interface as
"/sys/class/i2c-dev/i2c-0/subsystem/i2c-0".
nsekhar@ti.com: tested using i2cdetect and i2cdump.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since AM33XX supports only DT-boot, this is needed
for the appropriate device nodes to be created.
Note: OCMC RAM is part of the PER power domain and supports
retention. The assembly code for low power entry/exit will
run from OCMC RAM. To ensure that the OMAP PM code does not
attempt to disable the clock to OCMC RAM as part of the
suspend process add the no_idle_on_suspend flag.
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
things to device tree based booting.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mdSV
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.9/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards
From Tony Lindgren:
Minimal updates to OMAP board-*.c files while converting
things to device tree based booting.
* tag 'omap-for-v3.9/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap2plus_defconfig: enable omap1 rtc
RX-51: Register twl4030-madc device
RX-51: Add leds lp5523 names from Maemo 5 2.6.28 kernel
ARM: OMAP2+: AM33XX: omap2plus_defconfig: Add support for few drivers
ARM: OMAP1: nokia770: enable CBUS/Retu
ARM: OMAP2+: omap2plus_defconfig: enable CMA allocator
ARM: OMAP2+: omap2plus_defconfig: enable TFP410 chip support
ARM: OMAP3: igep0020: simplify GPIO LEDs dependencies
ARM: OMAP2+: craneboard: support the TPS65910 PMU
ARM: OMAP2+: craneboard: support NAND device
ARM: OMAP3: cm-t3517: add MMC support
ARM: OMAP2+: Remove apollon board support
+ Linux 3.8-rc6
Signed-off-by: Olof Johansson <olof@lixom.net>
Numerous updates to the various Tegra device trees are made:
* Addition of NVIDIA Beaver (Tegra30) and Toradex Colibri T20 and Iris
carrier boards.
* Enablement of the HDMI connector on most boards.
* Enablement of the keyboard controller on a few boards.
* Addition of the AC'97 controller to Tegra20.
* Addition of a GPIO poweroff node for TrimSlice.
* Changes to support the new "high speed UART" (DMA-capable) driver for
Tegra serial ports, and enablement for Cardhu's UART C.
* A few cleanups, such as compatible flag fixes, node renames, node
ordering fixes, commonizing properties into SoC .dtsi files, etc..
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-t114.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=UMMs
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren:
ARM: tegra: device tree updates
Numerous updates to the various Tegra device trees are made:
* Addition of NVIDIA Beaver (Tegra30) and Toradex Colibri T20 and Iris
carrier boards.
* Enablement of the HDMI connector on most boards.
* Enablement of the keyboard controller on a few boards.
* Addition of the AC'97 controller to Tegra20.
* Addition of a GPIO poweroff node for TrimSlice.
* Changes to support the new "high speed UART" (DMA-capable) driver for
Tegra serial ports, and enablement for Cardhu's UART C.
* A few cleanups, such as compatible flag fixes, node renames, node
ordering fixes, commonizing properties into SoC .dtsi files, etc..
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-t114.
* tag 'tegra-for-3.9-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (22 commits)
ARM: dt: tegra30: Rename "smmu" to "iommu"
ARM: dt: tegra20: Rename "gart" to "iommu"
ARM: tegra: move serial clock-frequency attr into the Tegra30 dtsi
ARM: tegra: Add Toradex Iris carrier board DT with T20 512MB COM
ARM: tegra: Add Colibri T20 512MB COM device tree
ARM: tegra: move serial clock-frequency attr into the Tegra20 dtsi
ARM: tegra: harmony: enable keyboard in DT
ARM: tegra: whistler: enable keyboard in DT
ARM: tegra: cardhu: register UARTC
ARM: tegra: seaboard: enable keyboard in DT
ARM: tegra: add DT entry for KBC controller
ARM: tegra: swap cache-/interrupt-ctrlr nodes in DT
ASoC: tegra: add ac97 host controller to device tree
ARM: DT: tegra: Add Tegra30 Beaver board support
ARM: DT: tegra: Add board level compatible properties
ARM: tegra: paz00: enable HDMI port
ARM: tegra: ventana: enable HDMI port
ARM: tegra: seaboard: enable HDMI port
ARM: tegra: trimslice: add gpio-poweroff node to DT
ARM: DT: tegra: Unify the description of Tegra20 boards
...
This pull request adds initial support for the Tegra114 SoC, which
integrates a quad-core ARM Cortex-A15 CPU. I'm proud to observe that we
posted the initial versions of these patches before the final official
announcement of this chip.
These patches are enough to boot with a UART-based console, support the
Dalmore and Pluto reference/evaluation boards, instantiate the GPIO and
pinctrl drivers, and enable a cpuidle state. As yet, no clocks or
storage devices are supported, but patches for those will follow shortly.
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-cpuidle, followed by a merge of the previous pull
request with tag tegra-for-3.9-scu-base-rework.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bIIe
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-t114' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stepen Warren:
ARM: tegra: add Tegra114 SoC support
This pull request adds initial support for the Tegra114 SoC, which
integrates a quad-core ARM Cortex-A15 CPU. I'm proud to observe that we
posted the initial versions of these patches before the final official
announcement of this chip.
These patches are enough to boot with a UART-based console, support the
Dalmore and Pluto reference/evaluation boards, instantiate the GPIO and
pinctrl drivers, and enable a cpuidle state. As yet, no clocks or
storage devices are supported, but patches for those will follow shortly.
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-cpuidle, followed by a merge of the previous pull
request with tag tegra-for-3.9-scu-base-rework.
* tag 'tegra-for-3.9-soc-t114' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (24 commits)
ARM: DT: tegra114: add pinmux DT entry
ARM: DT: tegra114: add GPIO DT entry
ARM: tegra114: select PINCTRL for Tegra114 SoC
ARM: tegra: add Tegra114 ARM_CPUIDLE_WFI_STATE support
ARM: tegra: Add SMMU entry to Tegra114 DT
ARM: tegra: add AHB entry to Tegra114 DT
ARM: tegra: Add initial support for Tegra114 SoC.
ARM: dt: tegra114: Add new board, Pluto
ARM: dt: tegra114: Add new board, Dalmore
ARM: dt: tegra114: Add new SoC base, Tegra114 SoC
ARM: tegra: fuse: Add chip ID Tegra114 0x35
ARM: OMAP: Make use of available scu_a9_get_base() interface
ARM: tegra: Skip scu_enable(scu_base) if not Cortex A9
ARM: Add API to detect SCU base address from CP15
ARM: tegra: Use DT /cpu node to detect number of CPU core
ARM: tegra: Add CPU nodes to Tegra30 device tree
ARM: tegra: Add CPU nodes to Tegra20 device tree
ARM: perf: simplify __hw_perf_event_init err handling
ARM: perf: remove unnecessary checks for idx < 0
ARM: perf: handle armpmu_register failing
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove/add conflict in arch/arm/mach-tegra/common.c resolved.
Remove/remove conflict in arch/arm/mach-tegra/platsmp.c. Leave the empty
stub function for now since removing it in the merge commit is confusing;
will be cleaned up in a separate commit. # # It looks like you may be
committing a merge. # If this is not correct, please remove the file #
.git/MERGE_HEAD # and try again.
The Tegra USB driver has a number of issues:
1) The PHY driver isn't a true platform device, and doesn't implement
the standard USB PHY API.
2) struct device instance numbers were used to make decisions in the
driver, rather than being parameterized by DT or platform data.
This pull request solves issue (2), and lays the groundwork for solving
issue (1). The work on issue (1) involved introducing new DT nodes for
the USB PHYs, which in turn interacted with the Tegra common clock
framework changes, due to the move of clock lookups into device tree.
Hence, these USB driver changes are taken through the Tegra tree with
acks from USB maintainers.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-soc-ccf.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8pTe
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: USB driver cleanup
The Tegra USB driver has a number of issues:
1) The PHY driver isn't a true platform device, and doesn't implement
the standard USB PHY API.
2) struct device instance numbers were used to make decisions in the
driver, rather than being parameterized by DT or platform data.
This pull request solves issue (2), and lays the groundwork for solving
issue (1). The work on issue (1) involved introducing new DT nodes for
the USB PHYs, which in turn interacted with the Tegra common clock
framework changes, due to the move of clock lookups into device tree.
Hence, these USB driver changes are taken through the Tegra tree with
acks from USB maintainers.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-soc-ccf.
* tag 'tegra-for-3.9-soc-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
usb: host: tegra: make use of PHY pointer of HCD
ARM: tegra: Add reset GPIO information to PHY DT node
usb: host: tegra: don't touch EMC clock
usb: add APIs to access host registers from Tegra PHY
USB: PHY: tegra: Get rid of instance number to differentiate PHY type
USB: PHY: tegra: get rid of instance number to differentiate legacy controller
ARM: tegra: add clocks properties to USB PHY nodes
ARM: tegra: add DT nodes for Tegra USB PHY
usb: phy: remove unused APIs from Tegra PHY.
usb: host: tegra: Resetting PORT0 based on information received via DT.
ARM: tegra: Add new DT property to USB node.
usb: phy: use kzalloc to allocate struct tegra_usb_phy
ARM: tegra: remove USB address related macros from iomap.h
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9hz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: Common Clock Framework rework
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
* tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (31 commits)
clk: tegra30: remove unused TEGRA_CLK_DUPLICATE()s
clk: tegra20: remove unused TEGRA_CLK_DUPLICATE()s
ARM: tegra30: remove auxdata
ARM: tegra20: remove auxdata
ASoC: tegra: remove auxdata
staging: nvec: remove use of clk_get_sys
ARM: tegra: paz00: add clock information to DT
ARM: tegra: add clock properties to Tegra30 DT
ARM: tegra: add clock properties to Tegra20 DT
spi: tegra: do not use clock name to get clock
ARM: tegra: remove legacy clock code
ARM: tegra: migrate to new clock code
clk: tegra: add clock support for Tegra30
clk: tegra: add clock support for Tegra20
clk: tegra: add Tegra specific clocks
ARM: tegra: define Tegra30 CAR binding
ARM: tegra: define Tegra20 CAR binding
ARM: tegra: move tegra_cpu_car.h to linux/clk/tegra.h
ARM: tegra: add function to read chipid
ARM: tegra: fix compile error when disable CPU_IDLE
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-tegra/common.c
arch/arm/mach-tegra/platsmp.c
drivers/clocksource/Makefile
- It fixes fec ptp clock pointer in device tree source.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJREL7uAAoJEFBXWFqHsHzO+1cH+QEeUwTqmlI2enO7XOxb4F5q
OijafxIi8+pYfQOZ6v/E70SaBaMyHQpG4WY3zQ+lrQlM/qCqAeEB/9KbkQU/1n8e
e1NF1Px/QisTcTF7qKwHhKurzgbuZ4vApX+IwCJyoGpYdEup9DxQxYvIqjUrwbdp
OdJ76kRkMkhj5D1WKRBOypStMRnDBr6e8Scc2iQspw8K9U1w+2g5kADGYGatEzOr
EcZ+EHIXJcBbX2938wakStshsanUlJEjdRbiQE8LQgaYYyHi9+S/xMvgDugwKbHY
OtOZ+vtQMOHeiusDQ01g7O3ZnsipWVMdk50hgBXxOZl4UHBHshQg5fG1dW+34Dw=
=2plf
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.8-4' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
imx fixes for 3.8, take 4
- It fixes fec ptp clock pointer in device tree source.
* tag 'imx-fixes-3.8-4' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx6: fix fec ptp clock slow 10 time
Fix the use of USART on both at91sam9x5 and at91sam9n12. In DTS, the
atmel,use-dma-[rx|tx] property is present but a DMA channel cannot be used.
Indeed the connexion between the DMA engine and the slave is not implemented
yet in Device Tree.
Note however that this property is also used for PDC (private DMA) on older
SoCs. This is why the driver alone cannot determine the validity of this
property.
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> [3.8+]
ptp should use enet_ref instead of pll6_enet
pll6_enet is fixed 500Mhz.
There are divider between enet_ref and pll6_enet
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- use rtc-mv in mvebu armv7 SoCs
- add pci-e hotplug for kirkwood
Depends on:
- tags/mvebu_fixes_for_v3.8-rc6
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRCqOnAAoJEAi3KVZQDZAewlUH/04tpMdf2rvgNP8uUVPVx62T
cXMga9qLTyXQ9hn31KP7fd/JPLRJFsG/+jy4x687EurJGIXXaWGNadjlE69DEPAZ
jt78sPa+Mo/xYD4XoNCr/ng1cbnTwc1ebSRSfN+nIjWynE8Do7tkOKxfJodTgQCM
XbE3EHfvAktKfJTsFDPsFwoIycEYxFsN4jQPwiCdPHVb24py3FWBy+qep7wtLfSO
gTnakEcOsQc7aFzrFdZ1ZnQ9KRlBYXVN636o4sQkM+UM9Vf7FAWBM4OCi2KP4trU
IlTzknoMAMYat+AtYzq1FcDmajeP/EgG6DbQh7lqUK0LEILn2rdAUlgN2QB3VIs=
=6oef
-----END PGP SIGNATURE-----
Merge tag 'drivers_for_v3.9' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu drivers for v3.9
- use rtc-mv in mvebu armv7 SoCs
- add pci-e hotplug for kirkwood
Depends on:
- tags/mvebu_fixes_for_v3.8-rc6
* tag 'drivers_for_v3.9' of git://git.infradead.org/users/jcooper/linux:
cpuidle: kirkwood: Move out of mach directory
rtc: Add support of rtc-mv for MVEBU SoCs
ARM: Kirkwood: Support basic hotplug for PCI-E
arm: mvebu: i2c come back in defconfig
arm: plat-orion: fix printing of "MPP config unavailable on this hardware"
Dove: activate GPIO interrupts in DT
Cubieboard has two LEDs available for use, a blue one (labeled LED1)
and a green one (labeled LED2).
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Highbank processors depend on the external ECME to perform voltage
management based on a requested frequency. Communication between the
A9 cores and the ECME happens over the pl320 IPC channel.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Changes to allow unplugging of CPU0 by Ulrich Hecht.
* Changes to add reg and device_type properties to cpus
device trees entries by Simon Horman.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=l7OU
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc2-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Second round of Renesas ARM-based SoC changes for v3.9
* Changes to allow unplugging of CPU0 by Ulrich Hecht.
* Changes to add reg and device_type properties to cpus
device trees entries by Simon Horman.
* tag 'renesas-soc2-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: mach-shmobile: sh73a0: allow unplugging of CPU0
ARM: mach-shmobile: add shmobile_cpu_disable_any()
ARM: mach-shmobile: emev2: Add reg and device_type properties to cpus
ARM: mach-shmobile: sh73a0: Add reg and device_type properties to cpus
Signed-off-by: Olof Johansson <olof@lixom.net>
- add missing gpio interrupt lines to dove dt
- fix bad logic for printing MPP error message on orion boards
- build proper serial port driver after changing mvebu DT compatible property
- This is a change to mvebu_defconfig that I wouldn't usually push out as a
fix. However, the commit
b24212f arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
changed the serial driver for the board in the dts file. without the patch
I've included in this pull, users won't see any log messages.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRB+cvAAoJEAi3KVZQDZAej/MH/2eWE2N3eTs8PRshCUoEIQxd
4uConsKhPiIyNK1rHePGI4EY/M07yxYRO7/55ajK5J3NiqxO7N8n0RYIMFsgNoC9
LCPpi2Ts6Rpj87jqj7ION6pfCiIDPE+Lj4hNQAVTuQAMrh04UqaDLHwpfQztETxW
C6X9A8ae+fVFfVQN0AusStImklxv5hf4odUhqvSKd6gy6n20KtV4EQQN+t+OLSgx
IsRUVww6cfqYFNYDWhyWg8SLppIp9m44hluS8f/wPT9zh5Wf6XWnvAZz41cqaf44
FpzURzHQGcmetqPv/MWL9YSCMTSmBxLfW4totTq2wgldl6qQc7bJsF3R0HlsUgc=
=EA67
-----END PGP SIGNATURE-----
Merge tag 'tags/mvebu_fixes_for_v3.8-rc6' into mvebu/boards
fixes for v3.8-rc6
- add missing gpio interrupt lines to dove dt
- fix bad logic for printing MPP error message on orion boards
- build proper serial port driver after changing mvebu DT compatible property
- This is a change to mvebu_defconfig that I wouldn't usually push out as a
fix. However, the commit
b24212f arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
changed the serial driver for the board in the dts file. without the patch
I've included in this pull, users won't see any log messages.
