Add support for DC-driven command mode. This is a mode where the video
stream sent by the display controller is packed into DCS command packets
(write_memory_start and write_memory_continue) by the DSI controller. It
can be used for panels with a remote framebuffer and is useful to save
power when used with a dynamic refresh rate (not yet supported by the
driver).
Signed-off-by: Thierry Reding <treding@nvidia.com>
For command mode panels, the DSI controller needs to be enabled and
configured so that panel drivers can send commands prior to the video
stream being enabled.
Move code from the monolithic output enable/disable functions into
smaller, reusable units to allow more fine-grained control over the
controller state.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The driver wasn't even attempting to do any cleanup when probing failed.
Fix this by releasing any resources acquired up to the point of failure
and putting the device back into the original state (reset, clocks off).
Signed-off-by: Thierry Reding <treding@nvidia.com>
DSI panels can always be hotplugged via the DSI bus' attach/detach
infrastructure, so unconditionally mark the connector hotpluggable.
While at it, also make sure that when a panel is detached the connector
is marked unconnected before calling into the DRM hotplug helpers to
reflect the correct state.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The common clock framework will take care of preparing and enabling the
parent of the DSI clock automatically.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In preparation for supporting command mode panels, don't disable the
clock when the output is disabled. The output will be enabled only after
the panel has been programmed in command mode, so the clock must always
remain on.
As a side-effect, pad calibration now only needs to be done at driver
probe time, since neither power nor controller state will go away before
driver removal. While at it, use a 32-bit variable to store register
content because the registers are 32-bit even on 64-bit Tegra.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than hardcoding them as macros, make the host and video FIFO
depths parameters so that they can be more easily adjusted if a new
generation of the Tegra SoC changes them.
While at it, set the depth of the video FIFO to the correct value of
1920 *words* rather than *bytes*.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously the panel and output were only enabled on encoder->dpms(). If
userspace called dpms on before doing a modeset, the driver would get into
a state where the connector had a dpms state of ON, but the encoder and output
were not enabled (because the encoder is not yet attached to the connector).
Subsequent dpms ON calls are ignored b/c the connector's state already matches
the desired state.
This patch enables/disables the panel and output on modeset as well, so we
can catch the above case.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both display controllers are in their own power partition. Currently the
driver relies on the assumption that these partitions are on (which is
the hardware default). However some bootloaders may disable them, so the
driver must make sure to turn them back on to avoid hangs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The introduction of the COMPILE_TEST dependency in commit 158b50aefa
(drm/tegra: Increase compile test coverage) removes the dependency on
COMMON_CLK (implicitly selected via ARCH_TEGRA, ARCH_MULTI_V7 and
ARCH_MULTIPLATFORM).
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the CRTC is enabled, make sure the VBLANK machinery is enabled.
Failure to do so will cause drm_vblank_get() to not enable the VBLANK on
the CRTC and VBLANK-synchronized page-flips won't work.
While at it, get rid of the legacy drm_vblank_pre_modeset() and
drm_vblank_post_modeset() calls that are replaced by drm_vblank_on()
and drm_vblank_off().
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This panel requires dual-channel mode. The device accepts command-mode
data on 8 lanes and will therefore need a dual-channel DSI controller.
The two interfaces that make up this device need to be instantiated in
the controllers that gang up to provide the dual-channel DSI host.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Drivers now no longer need to set the .owner field. It will be
automatically set at registration time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a function, of_find_mipi_dsi_device_by_node(), that can be used to
resolve a phandle to a MIPI DSI device.
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Provide small convenience wrappers to set the column and page extents of
the frame memory accessed by the host processors.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Provide small convenience wrappers to query or set the pixel format used
by the interface.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Provide a small convenience wrapper that transmits a DCS get_power_mode
command. A set of bitmasks for the mode bits is also provided.
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Provide a small convenience wrapper that transmits a DCS soft_reset
command.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Provide a small convenience wrapper that transmits a DCS nop command.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Integrate the MIPI DSI helpers into DocBook and clean up various
kerneldoc warnings. Also add a brief DOC section and clarify some
aspects of the mipi_dsi_host struct's .transfer() operation.
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add helpers for the {enter,exit}_sleep_mode, set_display_{on,off} and
set_tear_{on,off} DCS commands.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
[treding: kerneldoc and other minor cleanup]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement generic read and write commands. Selection of the proper data
type for packets is done automatically based on the number of parameters
or payload length.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the newly introduced mipi_dsi_set_maximum_return_packet_size()
function to replace an open-coded version.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function can be used to set the maximum return packet size for a
MIPI DSI peripheral.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
[treding: endianess, kerneldoc, return value]
Signed-off-by: Thierry Reding <treding@nvidia.com>
struct mipi_dsi_msg is a read-only structure, drivers should never need
to modify it. Make this explicit by making all references to the struct
const.
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently the mipi_dsi_dcs_write() function requires the DCS command
byte to be embedded within the write buffer whereas mipi_dsi_dcs_read()
has a separate parameter. Make them more symmetrical by adding an extra
command parameter to mipi_dsi_dcs_write().
The S6E8AA0 driver relies on the old asymmetric API and there's concern
that moving to the new API may be less efficient. Provide a new function
with the old semantics for those cases and make the S6E8AA0 driver use
it instead.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A common pattern is starting to emerge for higher level transfer
helpers. Create a new helper that encapsulates this pattern and avoids
code duplication.
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit introduces a new function, mipi_dsi_create_packet(), which
converts from a MIPI DSI message to a MIPI DSI packet. The MIPI DSI
packet is as close to the protocol described in the DSI specification as
possible and useful in drivers that need to write a DSI packet into a
FIFO to send a message off to the peripheral.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add two helpers, mipi_dsi_packet_format_is_{short,long}(), that help in
determining the format of a packet.
Signed-off-by: Thierry Reding <treding@nvidia.com>
drm_gem_object_release() called later in the drm_gem_cma_free_object()
function already calls this, so there's no need to do this explicitly.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some drivers treat the pitch and size fields as inputs and will use them
as minima provided by userspace so that they are only overwritten if the
minimal requirements of the driver exceed them.
This can cause strange behaviour when applications don't zero out these
fields, causing whatever was on the stack to be passed to the IOCTL. In
a typical case this would become visible as a failed allocation if the
pitch or size were unusually high. But this could also cause more subtle
bugs like overallocating dumb framebuffers.
To prevent drivers from misusing these values, make the DRM core zero
out the pitch and size fields before passing the structure to the driver
implementation.
While at it, also set the output handle field to zero for good measure,
even though it's less likely to be abused.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When creating a dumb buffer object using the DRM_IOCTL_MODE_CREATE_DUMB
IOCTL, only the width, height, bpp and flags fields are inputs. The
caller is not guaranteed to zero out or set handle, pitch and size.
Drivers must not treat these values as possible inputs, otherwise they
may use uninitialized memory during the computation of the framebuffer
size.
The R-Car DU driver treats the pitch passed in from userspace as minimum
and will only overwrite it when the driver-computed pitch is larger,
allowing userspace to, intentionally or not, overallocate framebuffers.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When creating a dumb buffer object using the DRM_IOCTL_MODE_CREATE_DUMB
IOCTL, only the width, height, bpp and flags fields are inputs. The
caller is not guaranteed to zero out or set handle, pitch and size.
Drivers must not treat these values as possible inputs, otherwise they
may use uninitialized memory during the computation of the framebuffer
size.
The OMAP driver uses the pitch field passed in by userspace as a minimum
and only override it if the driver-computed pitch is larger than what
userspace provided. To prevent this from causing overallocation, fix the
minimum pitch to 0 to enforce the driver-computed pitch.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function is similar to drm_gem_cma_dumb_create() but targetted at
kernel internal users so that they can override the pitch and size
requirements of the dumb buffer.
It is important to make this difference because the IOCTL says that the
pitch and size fields are to be considered outputs and therefore should
not be used in computations of the framebuffer size. Internal users may
still want to use this code to avoid duplication and at the same time
pass on additional, driver-specific restrictions on the pitch and size.
While at it, convert the R-Car DU driver, the single user that overrides
the pitch, to use the new internal helper.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Most of the functions already have the beginnings of kerneldoc comments
but are using the wrong opening marker. Use the correct opening marker
and flesh out the comments so that they can be integrated with the DRM
DocBook document.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
While at it, adjust the drm_gem_handle_create() function declaration to
be more consistent with other functions in the file.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The GMA500 driver redefines many constants already found in the generic
header. Replace uses of the custom defines by the standard ones and get
rid of the duplicate defininitions.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The prototype and the function implementation differ in their signature.
Make them consistent and use an unsigned integer for the number of modes
while at it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The number of pages can never be negative, so an unsigned type is
enough. This also matches the type of the n_pages argument of the
sg_alloc_table_from_pages() function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Creating a blob property will always copy the input data so the data
that is passed in can be const.
Signed-off-by: Thierry Reding <treding@nvidia.com>
size_t is the standard type when dealing with sizes of all kinds. Use it
consistently when instantiating DRM blob properties.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 1dce626404 introduced a regression
spotted on several G94 (FDObz #85160). This device seems to expect the
vblank period to be set after setting scale instead of before.
V2: shove this in a separate function
This is a candidate bug-fix for 3.18
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Tested-by: Zlatko Calusic <zcalusic@bitsync.net>
Tested-by: Michael Riesch <michael@riesch.at>
Tested-by: "poma" <pomidorabelisima@gmail.com>
Tested-by: Adam Williamson <adamw@happyassassin.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Commit "ltc/gf100-: fix cbc issues on certain boards" moved the setting
of the large page size bit from bar/nvc0 to fb/nvc0. GK20A uses its own
FB device and the change was thus not applied to it - fix this.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
atom scratch register race fix.
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add locking around atombios scratch space usage
Now exynos drm driver incurs infinite loop issue on multi-platform
reported by Matwey V.Korniliv like below,
http://comments.gmane.org/gmane.comp.video.dri.devel/117622
This issue is because non kms drivers enabled are probed before
a component master tries to bring up. This patch set resolves
the infinite loop issue and also includes fixups relevant to exynos
drm internal issues.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: fix possible infinite loop issue
drm/exynos: g2d: fix null pointer dereference
drm/exynos: resolve infinite loop issue on non multi-platform
drm/exynos: resolve infinite loop issue on multi-platform
These two arrays don't change, just make them constant,
reduces data segment by a few bytes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
