Pull drm fixes from Dave Airlie:
"Nothing too major or scary.
One i915 regression fix, nouveau has a tmds regression fix, along with
a regression fix for the runtime pm code for optimus laptops not
restoring the display hw correctly"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: make sure display hardware is reinitialised on runtime resume
drm/nouveau: punt fbcon resume out to a workqueue
drm/nouveau: fix regression on original nv50 board
drm/nv50/disp: fix dpms regression on certain boards
drm/i915: Flush the PTEs after updating them before suspend
We can use the same logic to walk the different bound/unbound lists
during shrinker (as the unbound list is a degenerate case of the bound
list), slightly compacting the code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just start with the basics for now.
Since there's a lot of different functionality in i915_irq.c I've
decided to split it into different sections and pull in just the
relevant functions. Splitting into different files looks like a lot
more work since the interrupt handlers do an awful lot of reuse all
over.
v2: Rebase onto changed function names.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's the new world order!
Not going full monty on these here and rolling this out throughout the
subsequent call chains since this is just for the kerneldoc. Later on
we can go more crazy, especially once we've embedded drm_device
correctly.
v2: Also frob the runtime_pm functions ...
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Double negations just parse harder. Also this allows us to ditch some
init code since clearing to 0 dtrt. Also ditch the assignment in
intel_pm_setup, that's not redundant since we do the assignement now
while setting up interrupts.
While at it do engage in a bit of OCD and wrap up the few lines of
setup/teardown code into little helper functions: intel_irq_fini for
cleanup and intel_irq_init_hw for hw setup.
v2: Use _install/_uninstall for the new wrapper function names as
Paulo suggested.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clear the override bits to make sure the hardware manages
the TX FIFO reset master on its own.
v2: Squash with the earlier attempt at forcing the override bits
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The register can house two different swing marging/deemph settings at
once. However only one gets used based on some other bits. Make sure we
set those bits correctly to make the hardware use the settings we
provided.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even though it's unliky, we should check each aux transaction not just
the first one. Also
commit ce31d9f4fc
Author: Rodrigo Vivi <rodrigo.vivi@intel.com>
Date: Mon Sep 29 18:29:52 2014 -0400
drm/i915: preserve other DP_TEST_SINK bits.
added a new aux transaction before the one which was checked. Fix
this.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Todd Previte <tprevite@gmail.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Inspired by Ville constifying the send buffer for pach_aux.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Use pack_aux() to construct the PSR exit DPMS D0 AUX message,
and use the defines from dp_dp_helper.h to populate the message
contents.
v2: Use sizeof() for message size (Jani)
Use a generic loop to write EDP_PSR_AUX_DATA registers
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This seems to have been accidentally lost in
commit be62acb4cc
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Fri Aug 30 16:19:28 2013 +0300
drm/i915: ban badly behaving contexts
Without this real gpu hangs only log output at info level, which gets
filtered away by piglit's testrunner.
v2: Tune down to notice level. Note that we need to add drm/i915 so
that at least the automatic igt dmesg filtering still picks it up.
v3: git add and lack of coffee don't mix well.
v4: Message is in between hw and sw reset, so switch verb to
continuous form.
v5: Use i915_stop_rings_allow_warn for consistency. For Chris' case of
injecting lots of hangs I guess we need to revamp this all anyway when
merging. For now this should plug the regression for piglit testing
mesa.
v6: Make it compile (Mika).
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Reported-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
I've decided not to document the functions exported to the audio
driver since really, they shouldn't exist ...
v2: Improvements from Imre's review plus a few more spelling fixes
I've spotted.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allows us to mark it static and so forgoe the kerneldoc for it.
Note that intel_power_domains_fini is also called from failure paths
in the driver load sequence. But the call to runtime_pm_disable for
that is harmless since by default runtime pm is already disabled.
v2: Augment the commit message as discussed with Imre on irc.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've decided to not move intel_display_port_power_domain because
that's just a hack in our design ...
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- fini goes with init, so call it intel_power_domains_fini. While
at it shovel some of the fini code that leaked out of it back in.
- give power_enabled functions the verb _is_ to make the meaning clearer.
Also use a __ prefix instead of _unlocked to really discourage users.
- rename runtime_pm_init/fini to enable/disable since that's what they do.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Geez is the audio hack ugly.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Rebased on top of the skl patches.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Another layer of indirection for just an lpt-only w/a is a bit
excessive. Reduce it.
This was added in
commit 7d708ee40a
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Apr 17 14:04:50 2013 +0300
drm/i915: HSW: allow PCH clock gating for suspend
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Oh well.
v2: Fix one more spelling fail Paulo spotted.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So I think I've spotted a small gap in the frontbuffer tracking
while discussing the logic with Paulo on irc:
1. Userspace schedules gpu rendering to the current frontbuffer.
This gets tracked in dev_priv->fb_tracking.busy_bits.
2. We pageflip a fully rendered buffer before the frontbuffer
rendering completes.
3. The request retiring will never clear busy_bits (since at retire
time the old frontbuffer won't have obj->frontbuffer_bits set), so
these bits now are stuck until someone again does a bit of frontbuffer
tracking.
If we clear stale busy_bits in flip_prepare this gap is closed.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell and later silicon has added a new pixel replication register
to the pipe timings for each transcoder. Now in addition to the
DPLL_A_MD register for the pixel clock double, we also need to write
to the TRANS_MULT_n (0x6002c) register to double the pixel data. Writing
to the DPLL only double the pixel clock.
ver2: Macro name change from MULTIPLY to PIPE_MULTI. (Daniel)
ver3: Do not set pixel multiplier if transcoder is eDP (Ville)
ver4: Macro name change to PIPE_MULT and default else pixel_multiplier
Cc: Ville =?iso-8859-1?Q?Syrj=E4l=E4?= <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Appease checkpatch and move one hunk back into the right
place that git am misplace!?]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL stage 1 patches still need polish so will likely miss the 3.18
merge window. We've decided to postpone to 3.19 so let's pull this in
to make patch merging and conflict handling easier.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Sink crc was implemented based on dp 1.1 spec that had all TEST_SINK bits
reserved reading all 0s. But when reviewing my latest changes on sink crc
Todd warned me that on new specs we have other valid bits on this reg that we
might want to preserve.
Cc: Todd Previte <tprevite@gmail.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It will be usefull to specify w/a that affects only BDW GT3.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In some cases like when PSR just got enabled the panel need more vblank
times to calculate CRC. I figured that out with the new PSR test cases
facing some cases that I had a green screen but a blank CRC. Even with
2 vblank waits on kernel + 2 vblank waits on test case.
So let's give up to 6 vblank wait time. However we now check for
TEST_CRC_COUNT that shows when panel finished to calculate CRC and
has it ready.
v2: Jani pointed out attempts decrements was wrong and should never reach
the error condition. And Daniel pointed out that EIO is more appropriated than
EGAIN. Also I realized that I have to read test_crc_count after setting
test_sink
v3: Rebase and adding error message
Cc: Todd Previte <tprevite@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some of the Thinkpads' firmware will issue a backlight change request
through i915 operation region unconditionally on AC plug/unplug, the
backlight level used is arbitrary and thus should be ignored. This is
handled by commit 0b9f7d93ca (ACPI / i915: ignore firmware requests
for backlight change). Then there is a Dell laptop whose vendor backlight
interface also makes use of operation region to change backlight level
and with the above commit, that interface no long works. The condition
used to ignore the backlight change request from firmware is thus
changed to: if the vendor backlight interface is not in use and the ACPI
backlight interface is broken, we ignore the requests; oterwise, we keep
processing them.
Fixes: 0b9f7d93ca (ACPI / i915: ignore firmware requests for backlight change)
Link: https://lkml.org/lkml/2014/9/23/854
Reported-and-tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the GPU frequency isn't going to change don't spam dmesg with
debug messages about it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
As we use WC updates of the PTE, we are responsible for notifying the
hardware when to flush its TLBs. Do so after we zap all the PTEs before
suspend (and the BIOS tries to read our GTT).
Fixes a regression from
commit 828c79087c
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Wed Oct 16 09:21:30 2013 -0700
drm/i915: Disable GGTT PTEs on GEN6+ suspend
that survived and continue to cause harm even after
commit e568af1c62
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 26 20:08:20 2014 +0100
drm/i915: Undo gtt scratch pte unmapping again
v2: Trivial rebase.
v3: Fixes requires pointer dances.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82340
Tested-by: ming.yao@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Todd Previte <tprevite@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
sg_alloc_table_from_pages() can build us a table with coalesced ranges which
means we need to iterate over pages and not sg table entries when releasing
page references.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Barbalho, Rafael" <rafael.barbalho@intel.com>
Tested-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
[danvet: Remove unused local variable sg.]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This reverts commit c76bb61a71.
It's apparently too broken so that Rodrigo submitted a patch to add a
config option for it. Given that the design is also ... suboptimal and
that I've only merged this to get lead engineers and managers off my
back for one second let's just revert this.
/me puts on combat gear again
It was worth a shot ...
References: http://mid.mail-archive.com/1411686380-1953-1-git-send-email-rodrigo.vivi@intel.com
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Daisy Sun <daisy.sun@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
BDW display - DP buffer translation values changed to give better margin.
Further change to entry 6; set dword 0 bit 31=1.
Both changes were approved already but this one didn't landed BSpec yet
this is why it is in a separated patch. Making reviewer's life easier.
Also alowing separated tests and any future bisect that might be needed.
Reference: Predator r74080 / HSD 4394389
v2: Arthur noticed I was changing the wrong bit.
Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's make sure PSR is propperly disabled before to re-enabled it.
According to Spec, after disabled PSR CTL, the Idle state might occur
up to 24ms, that is one full frame time (1/refresh rate),
plus SRD exit training time (max of 6ms),
plus SRD aux channel handshake (max of 1.5ms).
So if something went wrong PSR will be disabled until next full
enable/disable setup.
v2: The 24ms above takes in account 16ms for refresh rate on 60Hz mode. However
on low frequency modes this can take longer. So let's use 50ms for safeness.
v3: Move wait out of psr.lock critical area.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The sw cache clean on BDW is a tempoorary workaround because we cannot
set cache clean on blt ring with risk of hungs. So we are doing the cache clean on sw.
However we are doing much more than needed. Not only when using blt ring.
So, with this extra w/a we minimize the ammount of cache cleans and call it only
on same cases that it was being called on gen7.
The traditional FBC Cache clean happens over LRI on BLT ring when there is a
frontbuffer touch happening. frontbuffer tracking set fbc_dirty variable
to let BLT flush that it must clean FBC cache.
fbc.need_sw_cache_clean works in the opposite information direction
of ring->fbc_dirty telling software on frontbuffer tracking to perform
the cache clean on sw side.
v2: Clean it a little bit and fully check for Broadwell instead of gen8.
v3: Rebase after frontbuffer organization.
v4: Wiggle confused me. So fixing v3!
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The panel has to be reconfigured only when it really loose the power.
The traditional enable/disable sequence already take care of this so we can
minimize the time spend on every re-enable.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gen9 is different enough (for instance, fetching the memory latency
values is different from ILK+) to not take the HAS_PCH_SPLIT() branch,
so let's prefer a clean separation.
v2: Rebase on top of the broadwell_init_clock_gating() name change
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It can be handy to get the number of planes for this pipe, ie including
the primary plane to loop over them. Introduce a little function to do
so.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This can be useful to declare structures around pipes and planes and
don't have to go back auditing the code if the next platorm bump that
number.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's put to good use the new PLANE_CTL macros.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL Uses the same hardware for all planes now, so called "universal"
planes. Ie both the primary planes and sprite planes share the same
logic. This patch implements the drm_plane vfuncs for "sprites" ie
planes that aren't the primary plane.
v2: Couple of fixes:
- Actually enabled the planes and fix the plane number
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Skylake, we use plane1 as primary plane and plane2/3 as sprite
planes.
v2: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To accomodate the extra planes, the bit definitions were shuffled around
a bit.
v2: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument.
v3: Rebase after yet another change int that area (done with wiggle)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set gen 9 function pointers for eld write and global resource.
Implementation remains same as HSW.
v2: Rebase on top of Sonika's untangling of the if/else ladder (Damien)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
