For CRT and SDVO/HDMI, we need to use a normal, non-SSC, clock and so we
must clear any enabling bits left-over from earlier outputs. And also
seems to correct the LVDS panel on the Lenovo U160.
However, at one point, it did cause an "ERROR failed to disable
trancoder". So prolonged testing on top of Jesse's refactored and
error-checking CRTC logic is desired.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The i915 driver normally assumes the video bios has configured several
of the LVDS panel registers, and it just inherits the values. If the
vbios has not run, several of these will need to be setup.
If these are not correct then although the panel looks ok, output from an
HDMI encoder (eg, Chrontel CH7036) will be incorrect.
Signed-off-by: Mark Hayter <mdhayter@chromium.org>
[ickle: minor adjustments]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The i915 driver normally assumes the video bios has configured several
of the LVDS panel registers, and it just inherits the values. If the
vbios has not run, several of these will need to be setup. So we need to
check that the LVDS sync polarity is correctly configured per any
available modelines (e.g. EDID) and adjust if not, issuing a warning as
we do.
Signed-off-by: Mark Hayter <mdhayter@chromium.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
These make us increase our frequency much more readily, and decrease
them only after significant idle time, resulting in a 20% performance
increase for nexuiz.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Move code around and invoke iomem annotation in a few more places in
order to silence sparse. Still a few more iomem annotations to go...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
I changed 945's self refresh to work without the need for the driver to
enable/disable self refresh manually based on the idle state of the gpu.
This is much better than enabling/disabling self refresh for various
reasons, including staying in a lower power state for more time and
avoiding the need for cpu cycles.
This was originally done manually to workaround issues with the hardware
hanging. However, since 944001201: drm/i915: enable low power render
writes on GEN3 hardware, automatic CxSR seems stable.
Signed-off-by: Alexander Lam <lambchop468@gmail.com>
Acked-by : Li Peng <peng.li@linux.intel.com>
[ickle: play safe with the ordering and disable CxSR before tweaking any
watermark and enable afterwards.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
945 class hardware has an interesting quirk in which the vblank
interrupt is not raised if the CPU is in a low power state. (We also
suspect that the memory bus is clocked to the CPU/c-state and not the
GPU so there are secondary starvation issues.) In order to prevent the
most obvious issue of the low of the vblank interrupt (stuttering
compositing that only updates when the mouse is moving) is to install a
PM QoS request to prevent low c-states whilst the GPU is active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
eDP on the CPU doesn't need the PCH set up at all, it can in fact cause
problems. So avoid FDI training and PCH PLL enabling in that case.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to unlock the phase sync pointer enable bit before we can
actually enable the phase sync pointer workaround on Ironlake.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Factor out the FDI disable function (make it a mirror of
ironlake_fdi_enable) and add some FDI related assertions to the FDI
training code (we need an active pipe & plane before we start
transmitting bits).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Along with assertion checks for the FDI transmitters and receivers
(including PLLs). Modify the pipe enable function to check for FDI PLL
status as well, when driving PCH ports.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Otherwise our writes will be silently ignored.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With assertions to check transcoder and reference clock state.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
For pre-ILK only. Saves some code in the CRTC enable/disable functions
and allows us to check for pipe and panel status at enable/disable time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When PLLs or timing regs are changed, we need to make sure the panel
lock will allow it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add plane enable/disable functions to prevent duplicated code and allow
us to easily check for plane enable/disable requirements (such as pipe
enable, plane status, pll status etc).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On Ironlake+ we need to enable these in a specific order.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Admittedly, trusting ACPI or the BIOS at all to be correct is littered
with numerous examples where it is wrong. Maybe, just maybe, we will
have better luck using the ACPI OpRegion lid status...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Without this change, blits to the front buffer won't invalidate FBC
state, causing us to scan out stale data. Make sure we update these
bits on every FBC enable, since they may get clobbered if we shut off
the display.
References: https://bugzilla.kernel.org/show_bug.cgi?id=26932
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add a couple of missing workaround bits for ILK & SNB. These disable
clock gating on a couple of units that would otherwise prevent FBC from
working.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit dfe63bb0ad.
This commit was causing nouveau not to work properly, for -rc1 I'd
prefer it worked and we can look if this is useful for 2.6.39.
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hopefully, this is a temporary measure whilst the root cause is
understood. At the moment, we experience a hard hang whilst looping
urbanterror that has been identified as a result of the use of
semaphores, but so far only on SNB mobile.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32752
Tested-by: mengmeng.meng@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
After reordering the sequence of relocating objects, commit 6fe4f1404,
we can no longer rely on seeing all reloc targets prior to performing
the relocation. As a result we were ignoring the need to flush objects
from the render cache and invalidate the sampler caches, resulting in
rendering glitches. So we need to clear the relocation domains earlier.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On the fault path, commit 6fe4f140 introduction a regression whereby it
changed the sequence of the objects but continued to use the original
ordering of relocation entries. The result was that incorrect GTT offsets
were being fed into the execbuffer causing lots of misrendering and
potential hangs.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Whilst we had no older batches on the active list, everything was fine.
However, if the GPU is free running and the requests are only being
reaped by the periodic retirer, than the current seqno may not be at the
start of the list. In this case we need to select the first batch after
the last seqno written by the gpu and not inclusive of the seqno.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In order to workaround the issue with LVDS not working on the Lenovo
U160 apparently due to using the wrong SSC frequency, add an option to
disable SSC.
Suggested-by: Lukács, Árpád <lukacs.arpad@gmail.com>
Bugzillla: https://bugs.freedesktop.org/show_bug.cgi?id=32748
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
... and not if the maximum is non-zero. This fixes the typo introduced
in 47356eb672 and preserves the backlight value from boot.
[ickle: My thanks also to Indan Zupancic for diagnosing the original
regression and suggesting the appropriate fix.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org # after 47356eb672
As the mappable portion of the aperture is always a small subset at the
start of the GTT, it is allocated preferentially by drm_mm. This is
useful in case we ever need to map an object later. However, if you have
a large object that can consume the entire mappable region of the
GTT this prevents the batchbuffer from fitting and so causing an error.
Instead allocate all those that require a mapping up front in order to
improve the likelihood of finding sufficient space to bind them.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Rather than evicting an object at random, which is unlikely to alleviate
the memory pressure sufficient to allow us to continue, zap the entire
aperture. That should give the system long enough to recover and reap
some pages from the evicted objects, forestalling the allocation error
for the new object.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Before releasing the lock in order to copy the relocation list from user
pages, we need to drop all the object references as another thread may
usurp and execute another batchbuffer before we reacquire the lock.
However, the code was buggy and failed to clear the list...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
In order to retire active buffers whilst no client is active, we need to
insert our own flush requests onto the ring.
This is useful for servers that queue up some rendering and then go to
sleep as it allows us to the complete processing of those requests,
potentially making that memory available again much earlier.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Dave Airlie spotted that his ILK laptop with DMAR enabled was generating
the occasional DMAR warning.
"The ordering in the previous code was to rewrite the GTT table before
unmapping the pages and that makes sense to me."
This is his stable patch ported to d-i-n.
Reported-by: Dave Airlie <airlied@redhat.com>
Original-patch-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The docs recommend that if 8 display lines fit inside the FIFO buffer,
then the number of watermark entries should be increased to hide the
latency of filling the rest of the FIFO buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
FDI and the transcoders can fail for various reasons, so detect those
conditions and report on them.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cleanup several aspects of the rc6 code:
- misnamed intel_disable_clock_gating function (was only about rc6)
- remove commented call to intel_disable_clock_gating
- rc6 enabling code belongs in its own function (allows us to move the
actual clock gating enable call back into restore_state)
- allocate power & render contexts up front, only free on unload
(avoids ugly lazy init at rc6 enable time)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: checkpatch cleanup]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Enabling RC6 implies setting a graphics context. Make sure we do that
only after the ring has been enabled, otherwise our ring commands will
hang.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Re-enable rc6 support on Ironlake for power savings. Adds a debugfs
file to check current RC state, adds a missing workaround for Ironlake
MI_SET_CONTEXT instructions, and renames MCHBAR_RENDER_STANDBY to
RSTDBYCTL to match the docs.
Keep RC6 and the power context disabled on pre-ILK. It only seems to
hang and doesn't save any power.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As the IMR for the USER interrupts are not modified elsewhere, we can
separate the spinlock used for these from that of hpd and pipestats.
Those two IMR are manipulated under an IRQ and so need heavier locking.
Reported-and-tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to ensure that writes through the GTT land before any
modification to the MMIO registers and so must impose a mandatory write
barrier when flushing the GTT domain. This was revealed by relaxing the
write ordering by experimentally mapping the registers and the GATT as
write-combining.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
