This patch fixes up all of the build warnings for the pch_phub driver.
Cc: Masayuki Ohtake <masa-korg@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Packet hub driver of Topcliff PCH
Topcliff PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus. Packet hub is
a special converter device in Topcliff PCH that translate AMBA transactions
to PCI Express transactions and vice versa. Thus packet hub helps present
all IO peripherals in Topcliff PCH as PCIE devices to IA system.
Topcliff PCH has MAC address and Option ROM data.
These data are in SROM which is connected to PCIE bus.
Packet hub driver of Topcliff PCH can access MAC address and Option ROM data in
SROM via sysfs interface.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, the platform_bus allows customization of several of the
busses dev_pm_ops methods by using weak symbols so that platform code
can override them. The weak-symbol approach is not scalable when
wanting to support multiple platforms in a single kernel binary.
Instead, provide __init methods for platform code to customize the
dev_pm_ops methods at runtime.
NOTE: after these dynamic methods are merged, the weak symbols should
be removed from drivers/base/platform.c. AFAIK, this will only
affect SH and sh-mobile which should be converted to use this
runtime approach instead of the weak symbols. After SH &
sh-mobile are converted, the weak symobols could be removed.
Tested on OMAP3.
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In theory (although not *yet* in practice), a driver being passed
to platform_driver_probe might have driver.bus set to something
other than platform_bus_type. Locking drv->driver.bus is always
correct.
Signed-off-by: Patrick Pannuto <ppannuto@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Having the ddebug_query= boot parameter it makes sense to set up
dynamic debug as soon as possible.
I expect sysfs files cannot be set up via an arch_initcall, because
this one is even before fs_initcall. Therefore I splitted the
dynamic_debug_init function into an early one and a later one providing
/sys/../dynamic_debug/control file.
Possibly dynamic_debug can be initialized even earlier, not sure whether
this still makes sense then. I picked up arch_initcall as it covers
quite a lot already.
Dynamic debug needs to allocate memory, therefore it's not easily possible to
set it up even before the command line gets parsed.
Therefore the boot param query string is stored in a temp string which is
applied when dynamic debug gets set up.
This has been tested with ddebug_query="file ec.c +p"
and I could retrieve pr_debug() messages early at boot during ACPI setup:
ACPI: EC: Look up EC in DSDT
ACPI: EC: ---> status = 0x08
ACPI: EC: transaction start
ACPI: EC: <--- command = 0x80
ACPI: EC: ~~~> interrupt
ACPI: EC: ---> status = 0x08
ACPI: EC: <--- data = 0xa4
...
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: ---> status = 0x00
ACPI: EC: transaction start
ACPI: EC: <--- command = 0x80
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: jbaron@redhat.com
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
CC: linux-acpi@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dynamic debug lacks the ability to enable debug messages at boot time.
One could patch initramfs or service startup scripts to write to
/sys/../dynamic_debug/control, but this sucks.
This patch makes it possible to pass a query in the same format one can
write to /sys/../dynamic_debug/control via boot param.
When dynamic debug gets initialized, this query will automatically be
applied.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: jbaron@redhat.com
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The parsing and applying of dynamic debug strings is not only useful for
/sys/../dynamic_debug/control write access, but can also be used for
boot parameter parsing.
The boot parameter is introduced in a follow up patch.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: jbaron@redhat.com
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fortunately this is only exploitable on very unusual hardware.
[Reported a while ago but nothing happened so just fixing it]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These were (intentionally) stripped by "fix CFI macro
invocations to deal with shortcomings in gas" to expose problems
with unexpected splitting of arguments by older gas also on
newer versions, but as it turns out there is at least one distro
(Ubuntu 6.06) where even not having *any* spaces in a macro
argument doesn't reliably prevent splitting into multiple
arguments.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Alexander van Heukelum <heukelum@fastmail.fm>
LKML-Reference: <4CC157DB020000780001E8A2@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It turns out to generate something like this:
printk ( ("<3>") "something");
The extra parentheses here break the UML compile.
Change the sed-program to add the parentheses only for numbers.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Acked-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <1287696649.20421.1401306095@webmail.messagingengine.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since these boards can boot out of NAND, make sure we give u-boot its
own partition by default to avoid clobbering it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If the kernel's init section is merged back into the main memory region
during boot (which it should since that is how we've laid out the kernel
linker map), we want to make sure that these aren't counted as independent
regions. Otherwise, if a large mapping is attempted which starts in the
init region and extends into the main memory region, the access_ok func
will deny it. This leads to weird messages during runtime like "unable
to map xxx library" from the ldso but upon running the application again,
everything works fine.
So if the address of the end of the init region is the same as the start
of the main memory region, simply enlarge the memory region to include
the init region.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Many Blackfin parts group sets of pins into a single functional unit.
This means you cannot use different pins within a group for different
peripherals. Our resource conflict checking thus far has been limited
to individual pins, so if someone tried to grab a different pin from
the same group, it would be allowed while silently changing the other
pins in the same group.
One common example is the pin set PG12 - PG15 on BF51x parts. They
may either be used with SPI0 (1st function), or they may be used with
PTP/PWM/AMS3 (3rd function). Ideally, we'd like to use PG12 - PG14
for SPI0 while using PG15 with AMS3, but the hardware does not permit
this. In the past, the software would allow the pins to be requested
this way, but ultimately things like the Blackfin SPI driver would
stop working when the hardware rerouted to a different peripheral.
Signed-off-by: steven miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Flushing caches sometimes requires anomaly workarounds which require
supervisor-only insns. Normally we don't need to flush caches from
userspace so this isn't a problem, but when gcc generates trampolines
on the stack, we do.
So add a new syscall for gcc to use modeled after the mips version.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF54x processor has a ton of on-chip peripherals and in order to
support them all, the u-boot image is quite large. So give it 512KiB
in all bootable flashes to make our lives easier.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we include EMAC_SYSTAT when showing errors.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The predefined i2c address 0x2c doesn't match the configuration of the
ad5280 PINs AD0 and AD1 on the tftlcd add-on board. Both AD0 and AD1
are of voltage 3.3V, which means the i2c address should be 0x2F.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Nothing actually needs to use these MMRs (as direct cache manipulation
is done with the DTEST MMRs), so simply hide the read funcs behind the
anomaly define. They're generally unusable anyways when this anomaly
is in effect.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When apps run with their stack in L1, some system calls might be made
where a buffer is in the stack as an argument. So make sure the core
Blackfin access code does not reject this memory location.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This board has an AD1836 codec, so make sure we have the right resources
declared for it.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If an app is placing its stack in L1 scratchpad SRAM, make sure ptrace
is granted access to it so that gdb can do its thing.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The num_chipselect field for on-chip Blackfin SPI buses is supposed to
be 1 larger than the number of actual CSs available. This is because
the hardware starts counting at 1 and not 0. There is a field for "CS0",
but it is marked as "reserved" everywhere.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We don't need our own header and structure to hook up the ad5398 part,
so drop the custom resources for it.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than write our own ADP switch driver, use the existing fixed
regulator driver and rewrite the platform resources accordingly.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some peripherals might generate an error interrupt shortly after the
data interrupt due to the fact that the peripheral isn't serviced fast
enough. In most cases this isn't a problem and is expected behavior.
This hasn't been a problem on most parts since you simply don't request
the error interrupt (or you leave it disabled while there is an expected
state) and do the peripheral status checking in the data interrupt.
The Blackfin SIC allows people to prioritize data and error interrupts,
and the Blackfin CEC allows interrupts of equal or higher priority to
nest. The current default settings gives error interrupts a higher
priority than data interrupts. So if an error occurs while processing
the data interrupt, it will be serviced immediately.
However, the error interrupt on the BF537 SIC cannot be enabled on a
per-peripheral basis. Once the error interrupt is enabled for one
peripheral, it is automatically enabled for all peripherals.
Therefore lower the default multiplexed error interrupt priority so
most people need not worry themselves with this issue.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
With the recent kernel update the isp1362-hcd driver evaluates the
IORESOURCE_IRQ resource flags and requests the irq with the given
polarity/edge settings. However the ISP1362 config requires low
level/edge interrupts. Most of the Blackfin boards use some random
flag or no flag at all. Make all boards use a know good flag
IORESOURCE_IRQ_LOWEDGE.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The NAND platform driver expects the registers to have a "mem"
resource type rather than "io".
Signed-off-by: Valentin Yakovenkov <yakovenkov@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add platform resources for the on-chip CAN peripheral so we can use it.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
- Andi encountedred following warning with gcc 4.5
linux/block/cfq-iosched.c: In function ‘cfq_dispatch_requests’:
linux/block/cfq-iosched.c:2156:3: warning: array subscript is above array
bounds
- Warning happens due to following code.
slice = group_slice * count /
max_t(unsigned, cfqg->busy_queues_avg[cfqd->serving_prio],
cfq_group_busy_queues_wl(cfqd->serving_prio, cfqd, cfqg));
gcc is complaining about cfqg->busy_queues_avg[] being indexed by CFQ
prio classes (RT, BE and IDLE) while the array size is only 2.
- At run time, we never access cfqg->busy_queues_avg[IDLE] and return from
function before this code hits.
- To fix warning increase the array size though it will remain unused. This
patch also puts some comments to clarify some of the confusions.
- I have taken Jens's patch and modified it a bit.
- Compile tested with gcc 4.4 and boot tested. I don't have gcc 4.5
running, Andi can you please test it with gcc 4.5 to make sure it
worked.
Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Make sure we use the right Kconfig names and platform strings.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that we've rewritten the GPIO CS handling in the Blackfin SPI
peripheral, we need to update the platform resources accordingly.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the common header defines everything and the SPI drivers are
using it, we can drop these duplicated global namespace polluters.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On m68k, I/O macros like inb() outw() etc. are only defined to
something useful if CONFIG_ISA is set; dummies are in place if
not, but four macros were missing from the !CONFIG_ISA case.
Adding these makes some drivers, such as speakup, compile again.
Signed-off-by: Thorsten Glaser <tg@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
