This patch adds support for dropping gratuitous ARP frames which is
requirement for WFA Hotspot2.0.
Hotspot2.0 capability is enabled in driver if extended capabilities
IE from BSS descriptor has 11u interworking enabled.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
EXT_CAPAB_IE format involves IEEE header followed by bytestream of
capabilities. Current structure has incorrect member u8 for data;
fix it by defining it as u8[0].
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have usb_deregister() call in our rmmod routine. deauth,
shutdown etc. commands will be sent to FW later when bus
driver calls disconnect handler.
This mechanism works fine with SDIO and PCIe interfaces, but
there is an issue with USB.
USB bus driver returns all URBs submitted for receiving data
and command response immediately after usb_deregister() with
failure status. Hence we don't send deauth, shutdown etc.
command to firmware.
The problem is fixed by moving code from disconnect handler to
rmmod routine for USB interface.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tell the PCIe host core when the wifi is activated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables or disables power saving on the PCIe bus when the wifi is
in operation or not.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not called any more, do not export it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace the calls to bcma_core_pci_extend_L1timer() by calls to the
newly introduced bcma_core_pci_ip() and bcma_core_pci_down()
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wifi driver should tell the PCIe core that it is now in operation
so that some workarounds can be applied and the power state is changed.
This should replace the call to bcma_core_pci_extend_L1timer by the
brcmsmac driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This PCIe controller does not support a max read request size above 128
bytes. The sold card I tested this controller with used 128 as default
value, but some new routers are sold with BCM4331 chips, which have a
default max read request size of 512. This device fails at the first
DMA reqeust whch is bigger than 126 bytes.
This patch changes the max read request size to 128 for every device on
the PCIe link.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The values written into the BCN_OFFSET[01] registers are
hardcoded in the rt2800_init_register function.
Add a macro and a helper function to derive these values
directly from the base address of a given beacon, and use
the new function instead of the hardcoded numbers.
The patch contains no functional changes. The programmed
register values are the same before and after the patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW_BEACON_BASE() macro returns the base address
of a given beacon, however the returned values are
not usable on all chipsets. On devices which have
selectable shared memory parts, some beacon may be
located in the high part of the shared memory.
Instead of extending the already complicated macro,
add a new helper function and use that to get the
base address of a given beacon.
The actual patch contains no functional changes, the
helper function will be extended in a further patch
to handle different chipsets' requirements.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni reported that with mac80211_hwsim, multicast TX was causing
crashes due to invalid vif->cab_queue assignment. It turns out that
this is caused by change_interface() getting invoked and not having
the vif->type/vif->p2p assigned correctly before calling the queue
check (ieee80211_check_queues). Fix this by passing the 'external'
interface type to the function and adjusting it accordingly.
While at it, also fix the error path in change_interface, it wasn't
correctly resetting to the external type but using the internal one
instead.
Fortunately this affects on hwsim because all other drivers set the
vif->type/vif->p2p variables when changing iftype. This shouldn't
be needed, but almost all implementations actually do it for their
own internal handling.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix to return -ENOMEM in the netdev alloc error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Eric Dumazet says that my previous fix for an ERR_PTR dereference
(ea857f28ab 'ipip: dereferencing an ERR_PTR in ip_tunnel_init_net()')
could be racy and suggests the following fix instead.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code in the add bond vlan ids error
handling case instead of 0, as done elsewhere in this function.
Introduced by commit 1ff412ad77.
(bonding: change the bond's vlan syncing functions with the standard ones)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wildcarded flow support in kernel datapath.
Wildcarded flow can improve OVS flow set up performance by avoid sending
matching new flows to the user space program. The exact performance boost
will largely dependent on wildcarded flow hit rate.
In case all new flows hits wildcard flows, the flow set up rate is
within 5% of that of linux bridge module.
Pravin has made significant contributions to this patch. Including API
clean ups and bug fixes.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Link upper device properly. That will make IFLA_MASTER filled up.
Set the master to port 0 of the datapath under which the port belongs.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Flow table destroy is done in rcu call-back context. Therefore
there is no need to use rcu variant of hlist_del().
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
RCUfy dp-dump operation which is already read-only. This
makes all ovs dump operations lockless.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Flow dump operation is read-only operation. There is no need to
take ovs-lock. Following patch use rcu-lock for dumping flows.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Merge networking fixes from David Miller:
1) Revert Johannes Berg's genetlink locking fix, because it causes
regressions.
Johannes and Pravin Shelar are working on fixing things properly.
2) Do not drop ipv6 ICMP messages without a redirected header option,
they are legal. From Duan Jiong.
3) Missing error return propagation in probing of via-ircc driver.
From Alexey Khoroshilov.
4) Do not clear out broadcast/multicast/unicast/WOL bits in r8169 when
initializing, from Peter Wu.
5) realtek phy driver programs wrong interrupt status bit, from
Giuseppe CAVALLARO.
6) Fix statistics regression in AF_PACKET code, from Willem de Bruijn.
7) Bridge code uses wrong bitmap length, from Toshiaki Makita.
8) SFC driver uses wrong indexes to look up MAC filters, from Ben
Hutchings.
9) Don't pass stack buffers into usb control operations in hso driver,
from Daniel Gimpelevich.
10) Multiple ipv6 fragmentation headers in one packet is illegal and
such packets should be dropped, from Hannes Frederic Sowa.
11) When TCP sockets are "repaired" as part of checkpoint/restart, the
timestamp field of SKBs need to be refreshed otherwise RTOs can be
wildly off. From Andrey Vagin.
12) Fix memcpy args (uses 'address of pointer' instead of 'pointer') in
hostp driver. From Dan Carpenter.
13) nl80211hdr_put() doesn't return an ERR_PTR, but some code believes
it does. From Dan Carpenter.
14) Fix regression in wireless SME disconnects, from Johannes Berg.
15) Don't use a stack buffer for DMA in zd1201 USB wireless driver, from
Jussi Kivilinna.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
ipv4: expose IPV4_DEVCONF
ipv6: handle Redirect ICMP Message with no Redirected Header option
be2net: fix disabling TX in be_close()
Revert "genetlink: fix family dump race"
hso: Fix stack corruption on some architectures
hso: Earlier catch of error condition
sfc: Fix lookup of default RX MAC filters when steered using ethtool
bridge: Use the correct bit length for bitmap functions in the VLAN code
packet: restore packet statistics tp_packets to include drops
net: phy: rtl8211: fix interrupt on status link change
r8169: remember WOL preferences on driver load
via-ircc: don't return zero if via_ircc_open() failed
macvtap: Ignore tap features when VNET_HDR is off
macvtap: Correctly set tap features when IFF_VNET_HDR is disabled.
macvtap: simplify usage of tap_features
tcp: set timestamps for restored skb-s
bnx2x: set VF DMAE when first function has 0 supported VFs
bnx2x: Protect against VFs' ndos when SR-IOV is disabled
bnx2x: prevent VF benign attentions
bnx2x: Consider DCBX remote error
...
Merge fixes from Andrew Morton:
"A few fixes. One is a licensing change and I don't do licensing, so
please eyeball that one"
Licensing eye-balled.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
lib/lz4: correct the LZ4 license
memcg: get rid of swapaccount leftovers
nilfs2: fix issue with counting number of bio requests for BIO_EOPNOTSUPP error detection
nilfs2: remove double bio_put() in nilfs_end_bio_write() for BIO_EOPNOTSUPP error
drivers/platform/olpc/olpc-ec.c: initialise earlier
The LZ4 code is listed as using the "BSD 2-Clause License".
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Acked-by: Kyungsik Lee <kyungsik.lee@lge.com>
Cc: Chanho Min <chanho.min@lge.com>
Cc: Richard Yao <ryao@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ The 2-clause BSD can be just converted into GPL, but that's rude and
pointless, so don't do it - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The swapaccount kernel parameter without any values has been removed by
commit a2c8990aed ("memsw: remove noswapaccount kernel parameter") but
it seems that we didn't get rid of all the left overs.
Make sure that menuconfig help text and kernel-parameters.txt are clear
about value for the paramter and remove the stalled comment which is not
very much useful on its own.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Gergely Risko <gergely@risko.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the issue with improper counting number of flying bio requests for
BIO_EOPNOTSUPP error detection case.
The sb_nbio must be incremented exactly the same number of times as
complete() function was called (or will be called) because
nilfs_segbuf_wait() will call wail_for_completion() for the number of
times set to sb_nbio:
do {
wait_for_completion(&segbuf->sb_bio_event);
} while (--segbuf->sb_nbio > 0);
Two functions complete() and wait_for_completion() must be called the
same number of times for the same sb_bio_event. Otherwise,
wait_for_completion() will hang or leak.
Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove double call of bio_put() in nilfs_end_bio_write() for the case of
BIO_EOPNOTSUPP error detection. The issue was found by Dan Carpenter
and he suggests first version of the fix too.
Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Being a low-level component, various drivers (e.g. olpc-battery) assume
that it is ok to communicate with the OLPC Embedded Controller during
probe. Therefore the OLPC EC driver must be initialised before other
drivers try to use it. This was the case until it was recently moved
out of arch/x86 and restructured around commits ac2504151f ("Platform:
OLPC: turn EC driver into a platform_driver") and 85f90cf6ca ("x86:
OLPC: switch over to using new EC driver on x86").
Use arch_initcall so that olpc-ec is readied earlier, matching the
previous behaviour.
Fixes a regression introduced in Linux-3.6 where various drivers such as
olpc-battery and olpc-xo1-sci failed to load due to an inability to
communicate with the EC. The user-visible effect was a lack of battery
monitoring, missing ebook/lid switch input devices, etc.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Cc: Andres Salomon <dilinger@queued.net>
Cc: Paul Fox <pgf@laptop.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Seth reports that some APs, notably the Netgear WNDAP360, send
invalid ECSA IEs in probe response frames with the operating
class and channel number both set to zero, even when no channel
switch is being done. As a result, any scan while connected to
such an AP results in the connection being dropped.
Fix this by ignoring any channel switch announcment in probe
response frames entirely, since we're connected to the AP we
will be receiving a beacon (and maybe even an action frame) if
a channel switch is done, which is sufficient.
Cc: stable@vger.kernel.org # 3.10
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add flags intended to report various auxiliary information
and introduce the NL80211_RXMGMT_FLAG_ANSWERED flag to report
that the frame was already answered by the device.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[REPLIED->ANSWERED, reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to 802.11-2012 9.3.2.10, paragraph 4, QoS
data frames with a group address in the Address 1 field
have sequence numbers allocated from the same counter
as non-QoS data and management frames. Without this
flag, some drivers may not assign sequence numbers, and
in rare cases frames might get dropped. Set the control
flag accordingly.
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the mesh STA responds to probe request from legacy STA
but now it will only respond to legacy STA if the legacy STA does include
the specific mesh ID or wildcard mesh ID in the probe request.
The iw patch "iw: scan using meshid" can be used either by legacy STA
or by mesh STA to do active scanning by inserting the mesh ID in the
probe request frame.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Acked-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 currently sets WIPHY_FLAG_SUPPORTS_SCHED_SCAN based on whether
the start_sched_scan operation is supported or not, but that will not
be correct for all drivers, we're adding scheduled scan to the iwlmvm
driver but it depends on firmware support.
Therefore, move setting WIPHY_FLAG_SUPPORTS_SCHED_SCAN into the drivers
so that they can control it regardless of implementing the operation.
This currently only affects the TI drivers since they're the only ones
implementing scheduled scan (in a mac80211 driver.)
Acked-by: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
make the Freescale ethernet driver get, prepare and enable the FEC clock
during probe(); disable and unprepare the clock upon remove(), put is
done by the devm approach; hold a reference to the clock over the period
of use.
clock lookup is non-fatal as not all platforms provide clock specs in
their device tree; failure to enable specified clocks is fatal.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 720a43efd3
(drivers:net: Remove unnecessary OOM messages after netdev_alloc_skb)
there is a build warning:
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c: In function 'tx_skb_align_workaround':
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c:586:26: warning: unused variable 'fep'
Fix it.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can simply use the %pISc format specifier that was recently added
and thus remove some code that distinguishes between IPv4 and IPv6.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
another pull-request for net-next. It consists of two patches by Libo
Chen, the at91 and flexcan driver make use of platform_set_drvdata()
rather than open coding it. Chen Gang improves the error checking in
the c_can_platform driver's probe function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed when the cpsw driver is built as module.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP sends device configuration (see inet_fill_link_af) as an array
in the netlink information, but the indices in that array are not
exposed to userspace through any current santized header file.
It was available back in 2.6.32 (in /usr/include/linux/sysctl.h)
but was broken by:
commit 02291680ff
Author: Eric W. Biederman <ebiederm@xmission.com>
Date: Sun Feb 14 03:25:51 2010 +0000
net ipv4: Decouple ipv4 interface parameters from binary sysctl numbers
Eric was solving the sysctl problem but then the indices were re-exposed
by a later addition of devconf support for IPV4
commit 9f0f7272ac
Author: Thomas Graf <tgraf@infradead.org>
Date: Tue Nov 16 04:32:48 2010 +0000
ipv4: AF_INET link address family
Putting them in /usr/include/linux/ip.h seemed the logical match
for the DEVCONF_ definitions for IPV6 in /usr/include/linux/ip6.h
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rfc 4861 says the Redirected Header option is optional, so
the kernel should not drop the Redirect Message that has no
Redirected Header option. In this patch, the function
ip6_redirect_no_header() is introduced to deal with that
condition.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
commit fba875591 ("disable TX in be_close()") disabled TX in be_close()
to protect be_xmit() from touching freed up queues in the AER recovery
flow. But, TX must be disabled *before* cleaning up TX completions in
the close() path, not after. This allows be_tx_compl_clean() to free up
all TX-req skbs that were notified to the HW.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tcp_probe currently only supports analysis of IPv4 connections.
Therefore, it would be nice to have IPv6 supported as well. Since we
have the recently added %pISpc specifier that is IPv4/IPv6 generic,
build related sockaddress structures from the flow information and
pass this to our format string. Tested with SSH and HTTP sessions
on IPv4 and IPv6.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches fixes a rather unproblematic function signature mismatch
as the const specifier was missing for the th variable; and next to
that it adds a build-time assertion so that future function signature
mismatches for kprobes will not end badly, similarly as commit 22222997
("net: sctp: add build check for sctp_sf_eat_sack_6_2/jsctp_sf_eat_sack")
did it for SCTP.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is helpful to sometimes know the TCP window sizes of an established
socket e.g. to confirm that window scaling is working or to tweak the
window size to improve high-latency connections, etc etc. Currently the
TCP snooper only exports the send window size, but not the receive window
size. Therefore, also add the receive window size to the end of the
output line.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
1) Some constifications, from Mathias Krause.
2) Catch bugs if a hold timer is still active when xfrm_policy_destroy()
is called, from Fan Du.
3) Remove a redundant address family checking, from Fan Du.
4) Make xfrm_state timer monotonic to be independent of system clock changes,
from Fan Du.
5) Remove an outdated comment on returning -EREMOTE in the xfrm_lookup(),
from Rami Rosen.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
