The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stack currently detects reordering and avoid spurious
retransmission very well. However the throughput is sub-optimal under
high reordering because cwnd is increased only if the data is deliverd
in order. I.e., FLAG_DATA_ACKED check in tcp_ack(). The more packet
are reordered the worse the throughput is.
Therefore when reordering is proven high, cwnd should advance whenever
the data is delivered regardless of its ordering. If reordering is low,
conservatively advance cwnd only on ordered deliveries in Open state,
and retain cwnd in Disordered state (RFC5681).
Using netperf on a qdisc setup of 20Mbps BW and random RTT from 45ms
to 55ms (for reordering effect). This change increases TCP throughput
by 20 - 25% to near bottleneck BW.
A special case is the stretched ACK with new SACK and/or ECE mark.
For example, a receiver may receive an out of order or ECN packet with
unacked data buffered because of LRO or delayed ACK. The principle on
such an ACK is to advance cwnd on the cummulative acked part first,
then reduce cwnd in tcp_fastretrans_alert().
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bd61224b1c (SolutionEngine7724: fix Ether
support) has a typo in the 'phy_interface' field name of the platform data which
causes build error -- fix it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 06a64f91da (SH7619: fix Ether support) has
a typo in the 'phy_interface' field name of the platform data which causes build
error -- fix it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason, my PCIe RTL8111E onboard NIC on a GA-Z68X-UD3H-B3
motherboard reads as FFs when reading from MMIO with a block size
larger than 7. Therefore change to reading blocks of four bytes.
Ben Hutchings noted that the buffer is large enough to hold all
registers, so now all registers are read.
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 58ad436fcf.
It turns out that the change introduced a potential deadlock
by causing a locking dependency with netlink's cb_mutex. I
can't seem to find a way to resolve this without doing major
changes to the locking, so revert this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 platform driver fixes from Matthew Garrett:
"Three trivial fixes - the first reverts a patch that's broken some
other devices (again - I'm trying to figure out a clean way to
implement this), the other two fix minor issues in the sony-laptop
driver"
* 'linux-next' of git://cavan.codon.org.uk/platform-drivers-x86:
Revert "hp-wmi: Enable hotkeys on some systems"
sony-laptop: Fix reporting of gfx_switch_status
sony-laptop: return a negative error code in sonypi_compat_init()
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb and e1000e.
Akeem provides 3 igb patches, the first resets the link when EEE is enabled
or disabled if the link is up. His second patch changes a register read
which normally stores of the read value to "just-read" so that hardware
can accurately latch the register read. Lastly, he adds rcu_lock to avoid
a possible race condition with igb_update_stats function.
Mitch provides a fix for SR-IOV, where MSI-X interrupts are required, so
make sure that MSI-X is enabled before allowing the user to turn on SR-IOV.
Alex's igb patch make it so that we limit the lower bound for max_frame_size
to the size of a standard Ethernet frame. This allows for feature parity
with other Intel based drivers such as ixgbe.
Carolyn adds a SKU for a flashless i210 device and a fix for get_fw_version()
so that it works for all parts for igb. In addition, she has 2 igb patches
to refactor NVM code to accommodate devices with no flash. Lastly, she
adds code to check for the failure of pci_disable_link_state() to attempt
to work around a problem found with some systems.
Laura provides the remaining 2 igb patches. One removing the hard-coded
value for the size of the RETA indirection table, and creates a macro instead
for the RETA indirection table. The second adds the ethtool callbacks
necessary to change the RETA indirection table from userspace.
Bruce fixes a whitespace issue in a recent commit and resolves a jiffies
comparison warning by using time_after().
Li provides a fix for e1000e to avoid a kernel crash on shutdown by adding
one more check in e1000e_shutdown(). This is due to e1000e_shutdown()
trying to clear correctable errors on the upstream P2P bridge, when under
some cases we do not have the upstream P2P bridge.
v2:
- fixed patch 11 conditional statement from < to <= based on feedback
from Ben Hutchings
- fixed patch 12 patch description (adding the commit summary) based
on feedback from Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch completes the changes needed for supporting the
iPA variant cards of the BCM4313 wireless chipset.
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When changing channels the TSSI based power control needs to be
reinitialized.
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of additional phy registers needs to be programmed when
using TSSI-based power control.
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rework the code path in lcnphy tbl_init() for switch control
table programming. This also takes the iPA BT-combo card into
account.
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For lcnphy revision 1 or when hardware supports i/q calibration the
function wlc_lcnphy_set_txpwr_by_index() was called twice.
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The baseband multiplier must be zero during TSSI idle estimation
and restored afterwards.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The gain level control for the test tone has been changed. This
calbration test tone is used to determine the i/q compensation.
The i/q calibration routine has been reworked to accomodate this.
Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the transmit gain table for bcm4313 chip family.
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For debug purposes it is good to have the phy and radio information
available in the log. Only logged when driver is built when BRCMDBG
or BRCM_TRACING kconfig are set.
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts all sizeof(x)/sizeof(x[0]) instances to
ARRAY_SIZE macro in phytbl_lcn.c. The patch was made using
spatch with ARRAY_SIZE.cocci (see [1]).
[1] https://github.com/coccinelle/coccinelle/tree/master/demos/janitorings
Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function wlc_lcnphy_load_tx_gain_table() has a target PA
gain specified for the iPA variant of the bcm4313. This gain
value is reduced to avoid PA distortion. The if-statement is
removed because it was rather redundant in the first place.
Please note that this patch does not provide full iPA support.
Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleaning up some code fragments reducing indentation and uncluttering
some lines. Apart from whitespace there are no actual code changes
made.
Cc: Jonas Gorski <jogo@openwrt.org>
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a AR9485/WB225 based card.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bug 60747 - 1286:2044 [Microsoft Surface Pro]
Marvell 88W8797 wifi show 3 interface under network
https://bugzilla.kernel.org/show_bug.cgi?id=60747
This issue was also reported previously by OLPC and some folks from
the community.
There are 3 network interfaces with different types being created
when mwifiex driver is loaded:
1. mlan0 (infra. STA)
2. uap0 (AP)
3. p2p0 (P2P_CLIENT)
The Network Manager attempts to use all 3 interfaces above without
filtering the managed interface type. As the result, 3 identical
interfaces are displayed under network manager. If user happens to
click on an entry under which its interface is uap0 or p2p0, the
association will fail.
Work around it by removing the creation of AP and P2P interfaces
at driver loading time. These interfaces can be added with 'iw' or
other applications manually when they are needed.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This improves RX diversity and performance for AR9485.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Along with other chipsets, the Ralink driver uses the
frequency adjustment code for RF3053 as well. Remove
the bogus place-holder comment from the RF3053 specific
channel configuration function and call the frequency
adjustment function instead
Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RT3593_ChipSwitchChannel function in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the rt2800_adjust_freq_offset function before
the channel configuration functions to make it usable
from those without a forward declaration.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver, the RFCSR17 register can't be programmed in
one step on devices which are using the frequency
offset adjustment code.
Update the code to use step-by-step adjustment.
Reference:
RT30xxWriteRFRegister function in common/rt_rf.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the Ralink driver, there is an MCU
command which can be used to send the frequency
offset value directly to the USB device without
going through the RFCSR writing sequence.
Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RTMPAdjustFrequencyOffset function in common/rt_rf.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't write the new value into the register if it is
the same as the old value to avoid unncessary USB bus
traffic with USB devices. The change also saves a few
cycle on MMIO based devices.
Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RTMPAdjustFrequencyOffset function in common/rt_rf.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current code in the 'rt2800_adjust_freq_offset'
function limits the device specific frequency offset
value to FREQ_BOUND but ignores the fact that the
uppermost bit is not part of the frequency offset
value. As the result, the driver always uses the
FREQ_BOUND value if the uppermost bit is set.
Update the code to use the correct source value
for calculating the boundary.
Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RTMPAdjustFrequencyOffset function in common/rt_rf.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of precomputing the beacon base in
each caller, pass the beacon index to the
'rt2800_clear_beacon_register' function
and compute the beacon base in there.
This allows to simplify the caller functions
a bit.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The name of the HW_BEACON_OFFSET macro is a
bit confusing. It returns with one of the
HW_BEACON_BASE* values, so rename the macro
to HW_BEACON_BASE to reflect that.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we use struct efx_mtd to represent a physical NVRAM device
and struct efx_mtd_partition to represent a partition on that device.
But this only really makes sense for Falcon, as we don't know or care
whether MC-managed NVRAM partitions are on one or more physical
devices. It complicates iteration and provides little benefit.
Therefore:
- Replace the pointer to efx_mtd in mtd_info::priv with a pointer to efx_nic
- Move the falcon_spi_device pointer into the union in struct efx_mtd_partition
- Move the device name to efx_mtd_partition::dev_type_name
- Move the efx_mtd_ops pointer to efx_nic::mtd_ops
- Make efx_nic::mtd_list a list of partitions
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On Falcon we implement MAC filtering requested by the stack using the
MAC wrapper's single unicast filter and multicast hash filter. Siena
is very similar, though MAC configuration is mediated by the MC.
Since MCDI operations may sleep, reconfiguration is deferred from
ndo_set_rx_mode to a work item. However, it still updates the private
variables describing the filter state synchronously. Contrary to
comments, the later use of these variables is not protected using the
address lock, resulting in race conditions.
Move the state update to a new function
efx_farch_filter_sync_rx_mode() and make the Falcon-arch MAC
configuration functions call that, so that its use is consistently
serialised by the mac_lock.
Invert and rename the promiscuous flag to the more accurate
unicast_filter, and comment that both this and multicast_hash are
not used on EF10.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
MAC filters inserted on request from the stack (ndo_set_rx_mode)
should allow manual steering but not removal. Currently we have a
special case for Siena's all-multicast and all-unicast MAC filters,
but on EF10 we need to allow for steering of precise MAC filters as
well.
The EFX_FILTER_FLAG_RX_STACK flag changes the behaviour of replacement
and removal requests:
- Replacement *of* a filter with this flag never clears the flag but
does change steering and saved priority
- Replacement *by* a filter with this flag only sets the flag but does
not change steering
- Removal with priority < EFX_FILTER_PRI_REQUIRED really resets RX
steering and saved priority
This could support precise MAC filtering on Siena in future.
As a side-benefit, the default MAC filters are hidden from ethtool
until they are steered.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Move the special case for removal of default filters from
efx_farch_filter_table_clear_entry() into a wrapper function,
efx_farch_filter_table_remove(). Move the existence and priority
checks into the latter and use it where appropriate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Aside from accelerated RFS, there is almost nothing that can be shared
between the filter table implementations for the Falcon architecture
and EF10.
Move the few shared functions into efx.c and rx.c and the rest into
farch.c. Introduce efx_nic_type operations for the implementation and
inline wrapper functions that call these.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Currently every call to efx_farch_filter_table_clear_entry() is
shortly followed by a conditional reset of the table limits. The new
limits (0) are not pushed to hardware until the next filter insertion.
Move both the reset and the hardware reconfiguration into
efx_farch_filter_table_clear_entry(), and add an explanatory comment.
Also, make consistent use of the term 'search limit' for the maximum
number of probes the NIC must make when searching for a filter of a
particular type.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Move the common state from struct efx_filter_state into struct efx_nic.
Rename struct efx_filter_state to efx_farch_filter_state and change
the type of efx_nic::filter_state to void *.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Replace type field with match_flags. Add rss_context and match values
covering of most of what is now in the MCDI protocol.
Change some fields into bitfields so that the structure size doesn't grow
beyond 64 bytes.
Ditch the filter decoding functions as it is now easier to pick apart
the abstract structure.
Rewrite ethtool NFC rule functions to set/get filter match flags and
values directly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The filter table(s) on EF10 are managed by firmware and will need
almost entirely separate code. Rename the types and functions used
within the existing implementation. The current definition of struct
efx_filter_spec is really implementation-specific, so we need to keep
it. For now, define a separate structure for the internal
representation but leave them identical.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The PLL hang workaround is required only for AR9330 and
AR9340. This issue was first observed on an AP121 and the WAR
is enabled for AR9340 also (DB120 etc.), since it uses a PLL
design identical to AR9330. This is not required for AR9485 and AR9550.
Various bugs have been reported regarding this:
https://bugzilla.redhat.com/show_bug.cgi?id=997217https://bugzilla.redhat.com/show_bug.cgi?id=994648
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
