Remove the limitation of PAGE_SIZE to be 4k by defining the own
page size and macros for 4k. 8kb page size could be natively supported,
but it's disabled right now for simplicity.
Also, clean up using upper_32_bits() macro.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device seems supporting only U8, S16, S24_3LE, S32. Other linear
formats result in bad outputs.
Also, added the support for 32bit float format, which wasn't listed
in the original code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
PCM names for surround streams should be also fixed as well as the mixer
element names. Also, a bit clean up for PCM name setup.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We usually pick up "Surround" mixer for the rear output, and "Side"
for the extra surround. Fix the channel mapping to follow it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The prepare callback can be called multiple times, thus it needs to
release and acquire the resource again by itself at the second or later
call.
Simply add pcm_release_resources() at the beginning of each prepare
callback in ctatc.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the state variables for the driver filter and a function
to check if the filter is enabled and matches to the current device. The
check is built into the err_printk function.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Use schedule_timeout_interruptible() instead of open-coding the set and
schedule parts.
Cc: Mike Miller <mikem@beardog.cca.cpqcorp.net>
Cc: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add sysfs entries to the cciss driver needed for the dm/multipath tools.
A file for vendor, model, rev, and unique_id is added for each logical
drive under directory /sys/bus/pci/devices/<dev>/ccissX/cXdY. Where X =
the controller (or host) number and Y is the logical drive number.
A link from /sys/bus/pci/devices/<dev>/ccissX/cXdY/block:cciss!cXdY to
/sys/block/cciss!cXdY/device is also created. A bus is created in
/sys/bus/cciss. A link is created from the pci ccissX entry to
/sys/bus/cciss/devices/ccissX. Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix the SCSI reset error handler to send a working, properly addressed
reset message to the target device and add code to wait for the target
device to become ready by polling it with Test Unit Ready.
The existing reset code was broken in that it didn't bother to set the
8-byte LUN address to anything besides zero, so the command was addressed
to the controller, which pretended to the driver that the command
succeeded, while doing nothing. Ages ago I tested this code, but
unbeknownst to me, my test was flawed, and what I thought was a tape drive
getting reset was actually nothing of the sort. Unfortunately, there is
still lots of Smartarray firmware that doesn't handle doing target resets
right, and this code won't help in those cases, but it also shouldn't make
things worse in those cases than they already are.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Cc: Mike Miller <mikem@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Factor out the core of sendcmd() to provide a simpler interface which
exposes all the error information to the caller and make the original
sendcmd use this new function. Rationale: The SCSI error handling
routines need to send commands with interrupts turned off, but they also
need access to the full error information.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Cc: Mike Miller <mikem@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
SNDRV_PCM_SUBCLASS_GENERIC_MIX is mostly for h/w multi-stream playback
devices, but ca0106 and emu10k1x don't support it (unlike emu10k1).
We shouldn't set that flag to avoid confusion.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I forgot to remove on TOMOYO's 15th posting.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
This removes the prev_state field of struct perf_counter since
it is now unused. It was only used by the cpu migration
counter, which doesn't use it any more.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: John Kacur <jkacur@redhat.com>
LKML-Reference: <18979.35052.915728.626374@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes the cpu migration software counter to count
correctly even when contexts get swapped from one task to
another. Previously the cpu migration counts reported by perf
stat were bogus, ranging from negative to several thousand for
a single "lat_ctx 2 8 32" run. With this patch the cpu
migration count reported for "lat_ctx 2 8 32" is almost always
between 35 and 44.
This fixes the problem by adding a call into the perf_counter
code from set_task_cpu when tasks are migrated. This enables
us to use the generic swcounter code (with some modifications)
for the cpu migration counter.
This modifies the swcounter code to allow a NULL regs pointer
to be passed in to perf_swcounter_ctx_event() etc. The cpu
migration counter does this because there isn't necessarily a
pt_regs struct for the task available. In this case, the
counter will not have interrupt capability - but the migration
counter didn't have interrupt capability before, so this is no
loss.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: John Kacur <jkacur@redhat.com>
LKML-Reference: <18979.35006.819769.416327@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This arranges for perf_counter's notifier for cpu hotplug
operations to be called earlier than the migration notifier in
sched.c by increasing its priority to 20, compared to the 10
for the migration notifier. The reason for doing this is that
a subsequent commit to convert the cpu migration counter to use
the generic swcounter infrastructure will add a call into the
perf_counter subsystem when tasks get migrated. Therefore the
perf_counter subsystem needs a chance to initialize its per-cpu
data for the new cpu before it can get called from the
migration code.
This also adds a comment to the migration notifier noting that
its priority needs to be lower than that of the perf_counter
notifier.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <18981.1900.792795.836858@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If not passed as module option, provide an own card ID with the newly
introduced snd_set_card_id() call.
This will prevent ALSA from calling choose_default_name() which only
takes the last part of a name containing whitespaces. This for example
caused 'Audio 4 DJ' to be shortened to 'DJ', which was not very
descriptive.
The implementation now takes the short name and removes all whitespaces
from it which is much nicer.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce snd_card_set_id() function to allow lowlevel drivers to set
default identification name for card slot. The function checks also
for identification name collisions and tries to create unique name.
Also, the snd_card_create() function is simplified, because this new
function is used. As bonus, proper name collision checks are evaluated
at the card create time.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although the vmaster controls are created, they aren't registered thus
they don't appear in the real world. Added the missing snd_ctl_add()
calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
This patch fixes a bug which unconfigured struct tcf_proto keeps
chaining in tc_ctl_tfilter(), and avoids kernel panic in
cls_cgroup_classify() when we use cls_cgroup.
When we execute 'tc filter add', tcf_proto is allocated, initialized
by classifier's init(), and chained. After it's chained,
tc_ctl_tfilter() calls classifier's change(). When classifier's
change() fails, tc_ctl_tfilter() does not free and keeps tcf_proto.
In addition, cls_cgroup is initialized in change() not in init(). It
accesses unconfigured struct tcf_proto which is chained before
change(), then hits Oops.
Signed-off-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Tested-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
# make prefix=/usr/local V=1
gcc -o builtin-report.o -c -O2 -ggdb3 -Wall -Werror -Wstrict-prototypes -Wmissing-declarations -Wmissing-prototypes -std=gnu99 -Wdeclaration-after-statement -DSHA1_HEADER='<openssl/sha.h>' builtin-report.c
cc1: warnings being treated as errors
builtin-report.c: In function ‘__cmd_report’:
builtin-report.c:626: error: ‘cwdlen’ may be used uninitialized in this function
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <new-submission>
We currently build perf-stat/record etc, only to do nothing
with them. We also install the perf binary in two places,
$prefix/bin and $perfexec_instdir, which appears to be for
binaries which perf would exec were a command not linked in.
Correct this, and comment out broken/incomplete targets dist
and coverage.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: John Kacur <jkacur@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Short story: this laptop has 5.1 built-in speakers which you *really*
want to use (the not-so-"sub" woofer is what makes the audio above
average for a laptop), so 6-channel support is important (plus a decent
asound.conf to upmix stereo). It also has the 3 typical jacks that ought
to have a selectable mode. And it's based on ALC889, which sucks.
Rationale/explanations:
The const_channel_count stuff was added because, for a laptop like this,
you always have 6 channels available (internal speakers) but still need
to set the mode for the 3 external jacks. Therefore, the device always
needs to be in 6-channel mode but there still needs to be a mixer
control for the jack mode. You could use line/mic-in at the same time as
the 6 internal speakers, for example. You might be tempted to make it
even smarter by dynamically switching the max channel count when
headphones are plugged in (therefore muting the internal speakers and
reducing the physical channel count to the jack channel mode), but as a
user I consider this to be harmful because I want the audio to blow up
to 6 channels / upmixed as soon as I unplug the headphones, and having
opened the device while in 2-channel mode would prevent this from
working (and always making 6-channel mode available doesn't do any harm).
The hardware needs EAPD turned on and the DACs routed to the internal
speaker pins, so the patch adds those verbs.
The ALC889 CLFE and subsequent (side/aux, here unused) DACs do NOT work
by default, at least here. I wasted much time trying to talk to
Realtek/pshou about this, but they just kept sending me useless updates
to patch_realtek.c that did nothing relevant. In the end I gave up and
brute forced the issue by trying to flip every bit in the proprietary
coefficient registers, and eventually found the two magic registers that
need to be cleared to enable all DACs. I have only heard Acer users
complain, but that might be because ALC889 is pretty new and using 5.1
(and noticing the missing center/lfe channels) might not be that common.
If this is a generalized issue with all ALC889 systems then those verbs
should probably be moved to a common verb array.
The internal mic is untested and probably doesn't work.
These settings will probably work for other Acer Gemstone laptops with
the same 5.1 speaker config. When identified, those should be added to
the PCI subsystem ID list.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Patch to fix bad length checking in e1000. E1000 by default does two
things:
1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put
Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set. This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test). If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb. This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU. The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000. This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The serial number is of no interest in the longname, remove it. This
gives space for the usb path information which is more informative.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make .gitignore reflect perf_counter tools files so
git status doesn't gripe about untracked files.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a phy_power_down parameter to forcedeth: set to 1 to power down the
phy and disable the link when an interface goes down; set to 0 to always
leave the phy powered up.
The phy power state persists across reboots; Windows, some BIOSes, and
older versions of Linux don't bother to power up the phy again, forcing
users to remove all power to get the interface working (see
http://bugzilla.kernel.org/show_bug.cgi?id=13072). Leaving the phy
powered on is the safest default behavior. Users accustomed to seeing
the link state reflect the interface state and/or wanting to minimize
power consumption can set phy_power_down=1 if compatibility with other
OSes is not an issue.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GFS2 currently does not support mandatory flocks. An flock() call with
LOCK_MAND triggers unexpected behavior because gfs2 is not checking for
this lock type. This patch corrects that.
Signed-off-by: Abhi Das <adas@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
I found one more mis-conversion to the 'request is always dequeued
when completing' model in elv_abort_queue() during code inspection.
Although I haven't hit any problem caused by this mis-conversion yet
and just done compile/boot test, please apply if you have no problem.
Request must be dequeued when it completes.
However, elv_abort_queue() completes requests without dequeueing.
This will cause oops in the __blk_end_request_all().
This patch fixes the oops.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
it assumes we have an unaligned exception handler which
(a) may not be true
(b) costs a lot of performance
Instead we'll use struct/union method for big endian accesses,
and byte-shifting for little endian.
Signed-off-by: John Williams <john.williams@petalogix.com>
Use task_cred_xxx(task, security) in tomoyo_real_domain() to
avoid a get+put of the target cred.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
It's possible to recurse into filesystem from the memory
allocation, which deadlocks in xfs_qm_shake(). Add check
for __GFP_FS, and bail out if it is not set.
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Hedi Berriche <hedi@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
In the case where growing a filesystem would leave the last AG
too small, the fixup code has an overflow in the calculation
of the new size with one fewer ag, because "nagcount" is a 32
bit number. If the new filesystem has > 2^32 blocks in it
this causes a problem resulting in an EINVAL return from growfs:
# xfs_io -f -c "truncate 19998630180864" fsfile
# mkfs.xfs -f -bsize=4096 -dagsize=76288719b,size=3905982455b fsfile
# mount -o loop fsfile /mnt
# xfs_growfs /mnt
meta-data=/dev/loop0 isize=256 agcount=52,
agsize=76288719 blks
= sectsz=512 attr=2
data = bsize=4096 blocks=3905982455, imaxpct=5
= sunit=0 swidth=0 blks
naming =version 2 bsize=4096 ascii-ci=0
log =internal bsize=4096 blocks=32768, version=2
= sectsz=512 sunit=0 blks, lazy-count=0
realtime =none extsz=4096 blocks=0, rtextents=0
xfs_growfs: XFS_IOC_FSGROWFSDATA xfsctl failed: Invalid argument
Reported-by: richard.ems@cape-horn-eng.com
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Regreesion from commit ef8f7fc, which rearranged the code in
xfs_swap_extents() leading to double unlock of xfs inode ilock.
That resulted in xfs_fsr deadlocking itself on platforms, which
don't handle double unlock of rw_semaphore nicely. It caused the
count go negative, which represents the write holder, without
really having one. ia64 is one of the platforms where deadlock
was easily reproduced and the fix was tested.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
A race was found that if one were to enable and disable the function
profiler repeatedly, then the system can panic. This was because a profiled
function may be preempted just before disabling interrupts. While
the profiler is disabled and then reenabled, the preempted function
could start again, and access the hash as it is being initialized.
This just adds a check in the irq disabled part to check if the profiler
is enabled, and if it is not then it will just exit.
When the system is disabled, the profile_enabled variable is cleared
before calling the unregistering of the function profiler. This
unregistering calls stop machine which also acts as a synchronize schedule.
[ Impact: fix panic in enabling/disabling function profiler ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The trace_pipe did not recognize the latency format flag and would produce
different output than the trace file. The problem was partly due that
the trace flags in the iterator was not set as well as the trace_pipe
zeros out part of the iterator (including the flags) to be able to use
the same routines as the trace file. trace_flags of the iterator should
not cause any problems when not zeroed out by for trace_pipe.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
After converting the softirq tracer to use te flags options, this
caused a regression with the name. Since the flag was used directly
it was printed out (i.e. HRTIMER_SOFTIRQ).
This patch only shows the softirq name without the SOFTIRQ part.
[ Impact: fix regression of output from softirq events ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
A patch to allow the use of __print_symbolic and __print_flags
from a module. This allows the current GFS2 tracing patch to
build.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
LKML-Reference: <1243868015.29604.542.camel@localhost.localdomain>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
__string() is limited:
- it's a char array, but we may want to define array with other types
- a source string should be available, but we may just know the string size
We introduce __dynamic_array() to break those limitations, and __string()
becomes a wrapper of it. As a side effect, now __get_str() can be used
in TP_fast_assign but not only TP_print.
Take XFS for example, we have the string length in the dirent, but the
string itself is not NULL-terminated, so __dynamic_array() can be used:
TRACE_EVENT(xfs_dir2,
TP_PROTO(struct xfs_da_args *args),
TP_ARGS(args),
TP_STRUCT__entry(
__field(int, namelen)
__dynamic_array(char, name, args->namelen + 1)
...
),
TP_fast_assign(
char *name = __get_str(name);
if (args->namelen)
memcpy(name, args->name, args->namelen);
name[args->namelen] = '\0';
__entry->namelen = args->namelen;
),
TP_printk("name %.*s namelen %d",
__entry->namelen ? __get_str(name) : NULL
__entry->namelen)
);
[ Impact: allow defining dynamic size arrays ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4A2384D2.3080403@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Currently TP_fast_assign has a limitation that we can't define local
variables in it.
Here's one use case when we introduce __dynamic_array():
TP_fast_assign(
type *p = __get_dynamic_array(item);
foo(p);
bar(p);
),
[ Impact: allow defining local variables in TP_fast_assign ]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4A2384B1.90100@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Both event tracer and sched switch plugin are selected by default
by all generic tracers. But if no generic tracer is enabled, their options
appear. But ether one of them will select the other, thus it only
makes sense to have the default tracers be selected by one option.
[ Impact: clean up kconfig menu ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
