Nothing else is freeing it, and this mirrors the error handling path
already in ath5k_init_softc.
https://bugzilla.kernel.org/show_bug.cgi?id=37592
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Tsyvarev Andrey <tsyvarev@ispras.ru>
checking the status of PAPRD_AGC2_POWER(Log(ADC_power) measured after
last gain-change in dB) field suggests whether the PAPRD is completely/properly
done. This is an additional check apart from polling for PAPRD done bit being set.
Susinder suggests that the ideal power range value should be
0xf0 to 0xfe. With AR9382 we do have the values in this range. to have a
common check for all platforms we take agc2_power should be atleast greater
than 0xe0
Cc: susinder@qca.qualcomm.com
Cc: senthilb@qca.qualcomm.com
Cc: kmuthusa@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when the AP is configured with HT40/2.4GHz and when PAPRD is enabled in station
we have PAPRD training frames never sent out because of the following
failure "PAPRD target power delta out of range". This consistently happens
in channel 10,11 in Over The Air testing and rarely in channel 6 under wired
setup.
the reason behind this issue is all the HT40 rates target power
are 0 when we operate in channel 10/11 at 2.4GHz
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
core.h references ieee80211_ops but doesn't include mac80211.h, which issues
a warning once mac80211-compat.h is taken into use.
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd_chip.h contains one function with a pointer to ieee80211_hw but doesn't
include mac80211.h. As a temporary solution include mac80211.h to avoid
a warning.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hacks break once mac80211-compat.h is taken into use. Fix it by adding
an ifdef check.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hacks break once mac80211-compat.h is taken into use. Fix it by adding
an ifdef check.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are two devices with PCI ID 0x10ec:0x8192, namely RTL8192E and
RTL8192SE. The method of distinguishing them is by the revision ID
at offset 0x8 of the PCI configuration space. If the value is 0x10,
then the device uses rtl8192se for a driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Using 64bit stats on 32bit arches must use a synchronization or readers
can get transient values.
Fixes bug introduced in commit 6311cc44a2 (veth: convert to 64 bit
statistics)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as skb is given to hardware and spinlock released, TX completion
can free skb under us. Therefore, we should update netdev stats before
spinlock release.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we will not see the name of the slave dev in error
message:
[ 388.469446] (null): doesn't support polling, aborting.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add power_level module parameter to set the default power save level.
Power save level has range from 1 - 5, default power save level is 1.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Add power_save module parameter to enable power management if needed
Default power management is disabled.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since the irq number is just an unsigned int, store it inside iwl_bus
instead of calling the get_irq ops every time it is needed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since there is no protection around SYNC host command mechanism, at least WARN
when collision happens between two SYNC host comamnds. I am not sure there is a
real issue (beyond the HCMD_ACTIVE flag maintenance) with having two SYNC host
commands at the same time, but at least now, we will know about it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
All pci related stuff is in iwl-pci.c.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In order to remove a few more dereference to priv->pdev that will be killed
[Asoon, there is now a method to get the IRQ number.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The PCI_REVISION_ID is read and printed in iwl_pci_probe anyway using pr_info
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Continue to popule the PCI layer and the iwl_bus_ops with the power related
stuff.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Get a pointer to the struct device during probe and get the rid of all the PCI
specific DMA wrappers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since we have now a PCI layer, all the init and deinit code that is PCI
related should move to there.
Also move the IO functions: read8/read32/write32. They need hw_base which
is killed from priv.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Bus specific layer must know how to return the struct device* of the device.
Implement that as a callback of iwl_bus_ops and use that callback instead of
using the priv->pdev pointer which is meant to disappear soon.
Since the struct device * is needed in hot path, iwl_bus holds a pointer to it
instead of calling get_dev all the time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwl_bus will represent a bus, and iwl_bus_ops all the operations that can be
done on this bus.
For the moment only set_prv_data is implemented. More to come...
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Move some PCI functionality to the new iwl_pci.[ch] files:
* the PCI_DEVICE_TABLE
* the pci_driver struct definition
* the PCI probe / remove functions
* the PCI suspend / resume functions
All these functions are now split: the trigger comes from the PCI layer which
calls to the bus generic code located in the other files.
This is the beginning only. There are still a lot of PCI related code needs
to be gathered.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
It is superfluous to disable the interrupts after we reset the NIC. The only
entity that could enable the interrupts after the NIC is reset is the driver.
So remove this pointless action.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Firmware checking is only performed when the firmware is loaded
instead of each time the driver inits the phy.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The new firmware format adds versioning as firmware for a specific
chipset appears to be subject to change. Current "legacy" format is
still supported.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
