Zen Kato has a device which reports the 0xa RF type. The vendor driver
treats this as AL2230S, the same as devices with the AL2230S bit in the POD.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zen Kato's device has a regulatory domain value of 0x49, which is not an
IEEE 802.11 code and is not even identified in the vendor driver.
Recent versions of the vendor driver don't even look at the regdomain
value any more, and just allow channels 1-11 everywhere. This patch
brings us more in line with that behaviour, by allowing channels 1-11
for regdomains which we don't know about.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hi,
This is the third submission of the network driver for PS3.
The differences from the previous one are:
- renamed source file names so that their prefix can match
with the module name
- added cbe-oss-dev@ozlabs.org line for MAINTAINER file
- changed some in copyright comments
If there are no more comments, please apply for 2.6.23.
Thank you
--
Subject: PS3: Ethernet driver
From: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Add Gigabit Ethernet support for the PS3 game console. The module will
be called ps3_gelic.
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't turn the radio on until the interface is up. This saves some power in
case the driver is loaded but the card is not used.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Callers of enable_MAC() shouldn't have to worry about the bits in the
response's status word (and most of them don't). The return value is
sufficient information.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Matteo Croce reported Aironet initialization failures. They were caused by
a race in airo. airo finds a free interface name, then initializes the card
and finally registers the interface. Another device may get the same name
in the meantime.
The reason airo gets its name early is to use it in informative printks and
to name the resources it requests. The printks will be just fine without
the interface name and the resources can use the driver's name - that's
what other network drivers do anyway.
One of the talkative functions is setup_card(). It is called once before
registration and can be called later again. Let's have an empty dev->name
during the first call, so it doesn't print the ugly "airo(eth%d)" message.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
airo's kernel thread and the IRQ handler are needed only when the interface
is up.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an assymetry between pci_{enable,disable}_device. airo did not disable
the PCI device when unloading the module. This caused suspend failures
after modprobe -r airo && modprobe airo.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When allocating out_mad in show_pma_counter(), take sizeof *out_mad
instead of sizeof *in_mad. It is true that today the type of in_mad
and out_mad are the same, but this patch will give us a cleaner code.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Similar patch to ipw2200. Round the timer used for RF kill
switch off to 1 second boundary to save power.
Build tested only, don't have this hardware.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the ipw2200 driver polling of rf kill switch occur on second boundaries to reduce
power. Making all the wakeup's in the system occur together reduces power, and keeps
CPU in idle longer.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I failed to notice that a u16 was being passed to the hardware.
This fixes it.
Thanks to Kasper F. Brandt for finding this!
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... by removing an ill-conceived, useless line. Discovered by coverity.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove a header file that was ostensibly "removed" before, in commit
3ce40232.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a capability flag that is used by the DLPAR userspace
tool to check which DLPAR features are supported by the eHEA driver.
Missing goto has been included.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At present, when a device is enslaved to bonding, if ipv6 is
active then addrconf will be initated on the slave (because it is closed
then opened during the enslavement processing). This causes DAD and RS
packets to be sent from the slave. These packets in turn can confuse
switches that perform ipv6 snooping, causing them to incorrectly update
their forwarding tables (if, e.g., the slave being added is an inactve
backup that won't be used right away) and direct traffic away from the
active slave to a backup slave (where the incoming packets will be
dropped).
This patch alters the behavior so that addrconf will only run on
the master device itself. I believe this is logically correct, as it
prevents slaves from having an IPv6 identity independent from the
master. This is consistent with the IPv4 behavior for bonding.
This is accomplished by (a) having bonding set IFF_SLAVE sooner
in the enslavement processing than currently occurs (before open, not
after), and (b) having ipv6 addrconf ignore UP and CHANGE events on
slave devices.
The eql driver also uses the IFF_SLAVE flag. I inspected eql,
and I believe this change is reasonable for its usage of IFF_SLAVE, but
I did not test it.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
usbnet_probe() handles a positive return value from the driver bind()
function as success, but will later only setup the status handler if the
return value was zero, leading to confusion. Patch adjusts this to accept
positive values as success in both checks.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Get rid of dubious casts to (void *) which causes a sparse warning.
And move largeish function from inline to the one file that uses the code,
the compiler can then decide to inline it.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Based on an original idea by John W. Linville.
It is the missing part of 42d45ccd60636c28e35c2016f091783bc14ad99c
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add 88E1112 PHY ID to the marvell driver. Seems to do fine with the
88E1111 inits.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify the marvell driver init a bit: Make the supported devices an
array instead of explicitly registering each structure. This makes it
considerably easier to add new devices down the road.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Support for the Asix AX88796 network controller, an
NE2000 compatible 10/100 ethernet device with internal
PHY.
The driver supports PHY settings via either ioctl() or
the ethtool driver ops.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Here's a slightly cleaner way of creating the /proc structure for the
pnx8850. mostly, it creates a directory with default mode 555, since the
one you're creating is mode 444, which is somewhat unusual for a directory
under /proc.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Using another systems defines is a safe way to get your code broken by
accident when that system is removed.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch is an workaround for these sparse warnings:
linux/include/linux/calc64.h:25:17: warning: symbol '__quot' shadows an earlier one
linux/include/linux/calc64.h:25:17: originally declared here
linux/include/linux/calc64.h:25:17: warning: symbol '__mod' shadows an earlier one
linux/include/linux/calc64.h:25:17: originally declared here
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Export contents of struct mips_fpu_emulator_stats via debugfs.
There is no way to read these statistics for now but they (at least
the "emulated" count) might be sometimes useful for performance tuning
on FPU-less CPUs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently a number of unaligned instructions is counted but not used.
Add /debug/mips/unaligned_instructions file to show the value.
And add /debug/mips/unaligned_action to control behavior upon an
unaligned access. Possible actions are:
0: silently fixup the unaligned access.
1: send SIGBUS.
2: dump registers, process name, etc. and fixup.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Fix pci ops for secondary PCIC
* Do not reserve 1MB for PCI MEM region (leave PCIBIOS_MIN_MEM zero)
* Use platform_device to provide ethernet addresses for internal NICs.
(background: TX49XX SoCs include PCI NIC (TC35815 compatible)
connected via its internal PCI bus, but the NIC's PROM interface is
not connected to SEEPROM. So we must provide its ethernet address
by another way.)
* Check return value of early_read_config_word()
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TX49XX SoCs include PCI NIC (TC35815 compatible) connected via its
internal PCI bus, but the NIC's PROM interface is not connected to
SEEPROM. So we must provide its ethernet address by another way.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TX39XX and TX49XX have "reserved" segment in CKSEG3 area.
0xff000000-0xff3fffff on TX49XX and 0xff000000-0xfffeffff on TX39XX
are reserved (unmapped, uncached). Controllers on these SoCs are
placed in this segment.
This patch add plat_ioremap() and plat_iounmap() to override default
behavior and implement these hooks for TX39/TX49.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use rtc-rs5c348 and at25 spi protocol driver and spi_txx9 spi
controller driver instead of platform dependent codes.
This patch also removes dependencies to old RTC interfaces such as
rtc_mips_get_time, etc.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
GPIO 0..15 are for TX4938 PIO pins, GPIO 16..18 are for FPGA-driven
chipselect signals for SPI devices.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- use RTC_CLASS instead of GEN_RTC
- get rid of ds1216 in favour of a RTC_CLASS driver
- use correct console device for older RM400
- use physical addresses for 82596 device
- use 128 byte L1 cache line size (this is needed because most of the
SNI caches are using 128 L2 cache lines)
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
