All SH-4 parts have a 4-digit year, while the SH-3 parts typically
only use a 2-digit one. The SH7705, SH7710, and SH7712 SH-3 parts
however opted to extend it to 4-digit and still look and act like
an SH-3 RTC in all other ways.
This adds a capability flag (RTC_CAP_4_DIGIT_YEAR) that these
corner-case CPU subtypes can set in their platform data and cleans
up some of the ifdef mess in the driver as a result.
Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific interrupt setup code for x3 from
intc2 to intc. New vectors are also added to match the preliminary
information.
Use plat_irq_setup_pins() to select between IRQ and IRL mode for IRQ0-3.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The intc tables for sh3 currently contain a typo where the bit
fields in IPRD are mixed up for IRQ4 and IRQ5. This patch makes
sure the correct bit fields are used - all according to the
datasheets.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The new intc code handles IRQ3 and IRQ7 in the cpu specific code
already, so there is no reason to duplicate that here.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific interrupt setup code for sh7760
from ipr + intc2 to intc. New vectors are also added to match the
information provided by the datasheet.
Vectors for IRQ4-IRQ7 are enabled by default. Use plat_irq_setup_pins()
if pins IRL0-3 should be used in IRLM mode.
The patch also adds the SIM block to the serial port platform data.
Version two of this patch fixes MMCIF problems reported by Manuel Lauss.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific interrupt setup code for sh7785
from intc2 to intc. New vectors are also added to match the information
provided by the datasheet.
No IRQ/IRL pin vectors are enabled by default. Use plat_irq_setup_pins()
to select between IRL and IRQ mode.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reworks the cache mode configuration in Kconfig, and allows for
explicit selection of write-back/write-through/off configurations.
All of the cache flushing routines are optimized away for the off
case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes sure that the sh7710 specific ipsec vector is missing
if building for a sh7712. All according to the datasheet.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a few missing vectors for sh7707. The only interrupt
controller differences between sh7707 and sh7709 seem to be added
vectors for one LCD controller and two PCMCIA slots.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch unifies the cpu specific interrupt setup code for
sh7706, sh7707, sh7708 and sh7709 and moves the code into a new
file called setup-sh770x.c. It makes sense to share the setup code
between these processors because most hardware blocks are identical
from a software point of view. With this patch the sh770x processors
now have a complete set of vectors that match with the information
provided by the data sheets. This is a big improvement for sh7708.
Vectors for IRQ4 and IRQ5 are enabled by default. Use
plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.
This patch also unifies the platform device setup code which means
that the rtc driver now has platform data for all sh770x processors.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific interrupt setup code
for sh7710 from ipr to intc. While at it new vectors are added
to match the information provided by the datasheet. Version two
simplifies the Kconfig part.
Vectors for IRQ4 and IRQ5 are enabled by default. Use
plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.
This patch also adds sh7710 specific platform data for the rtc
driver. The base address of SCIF1 is adjusted to match the
datasheet.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific interrupt setup code for
sh7705 from ipr to intc. While at it new vectors are added to
match the information provided by the datasheet.
Vectors for IRQ4 and IRQ5 are enabled by default.
Use plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.
This patch also adds sh7705 specific platform data for the rtc driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There's an obvious typo in arch/i386/boot/header.S (in your
linux-2.6-x86setup.git) that I noticed by just studying the code.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
wakeup.S looks at the video mode number from the setup header and
looks to see if it is a VESA mode. Unfortunately, the decoding is
done incorrectly and it will attempt to frob the VESA BIOS for any
mode number 0x0200 or larger. Correct this, and remove a bunch of #if
0'd code.
Massive thanks to Jeff Chua for reporting the bug, and suffering
though a large number of experiments in order to track this problem
down.
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Canonicalize the video mode number as presented to the kernel. The
video mode number may be user-entered (e.g. ASK_VGA), an alias
(e.g. NORMAL_VGA), or a size specification, and that confuses the
suspend wakeup code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
According to PowerPC 440EPx documentation,
MAL0 is comprised of four channels (two transmit and two receive).
Each channel is dedicated to one of two EMAC cores.
This patch fixes Sequoia DTS MAL0 entry and EMAC entries,
assigning correct channel numbers to EMACs.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The patch adds support for the 64-bit resources to the PCI
iomap code.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The EP93XX_GPIO_LINE_F() macro is supposed to be called with a line
number between 0 and 7, but the current code causes it to get called
with an spuriously offset number range {16..23}.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A new binding for flash devices was recently introduced. This updates the
Sequoia DTS to use the new binding and enabled MTD in the defconfig.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Stefan Roese <sr@denx.de>
A new binding for flash devices was recently introduced. This updates the
Walnut DTS to use the new binding.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Add a cuboot wrapper for the Bamboo board. Additionally, we enable MAC
address fixups for both cuboot and treeboot.
This also removes some obsoleted linker declarations that have been
moved into ops.h
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix timekeeping on PowerPC 601
[POWERPC] Don't expose clock vDSO functions when CPU has no timebase
[POWERPC] spusched: Fix null pointer dereference in find_victim
Randy Dunlap noticed an interesting "crashme" behaviour on his dual
Prescott Xeon setup, where he gets page faults with the error code
having a zero "user" bit, but the register state points back to user
mode.
This may be a CPU microcode buglet triggered by some strange instruction
pattern that crashme generates, and loading a microcode update seems to
possibly have fixed it.
Regardless, we really should trust the register state more than the
error code, since it's really the register state that determines whether
we can actually send a signal, or whether we're in kernel mode and need
to oops/kill the process in the case of a page fault.
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a workaround to address warnings generated on the "n" constraint by
GCC 3.3 and below.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the definition of the ioasic_ssr_lock spinlock to include a proper
initialisation.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes a crash caused by an interrupt coming in when an IRQ stack
is being torn down. When this happens, handle_signal will loop, setting up
the IRQ stack again because the tearing down had finished, and handling
whatever signals had come in.
However, to_irq_stack returns a mask of pending signals to be handled, plus
bit zero is set if the IRQ stack was already active, and thus shouldn't be
torn down. This causes a problem because when handle_signal goes around
the loop, sig will be zero, and to_irq_stack will duly set bit zero in the
returned mask, faking handle_signal into believing that it shouldn't tear
down the IRQ stack and return thread_info pointers back to their original
values.
This will eventually cause a crash, as the IRQ stack thread_info will
continue pointing to the original task_struct and an interrupt will look
into it after it has been freed.
The fix is to stop passing a signal number into to_irq_stack. Rather, the
pending signals mask is initialized beforehand with the bit for sig already
set. References to sig in to_irq_stack can be replaced with references to
the mask.
[akpm@linux-foundation.org: use UL]
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xen ignores all updates to cr4, and some versions will kill the domain if
you try to change its value. Just ignore all changes.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found a type mismatch in UML that makes host block devices unusable as ubd
devices on x86_64 and other 64 bits systems (segfault of the mm subsystem):
In block/ioctl.c, the following lines show that the BLKGETSIZE ioctl expects
a pointer to a long:
case BLKGETSIZE:
if ((bdev->bd_inode->i_size >> 9) > ~0UL)
return -EFBIG;
return put_ulong(arg, bdev->bd_inode->i_size >> 9);
In arch/um/os-Linux/file.c, os_file_size calls it with an int.
The ioctl_list man page should be fixed as well.
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent changes to the timekeeping code broke support for the PowerPC 601
processor which doesn't have the usual timebase facility but a slightly
different thing called (yuck) the RTC.
This fixes it, boot tested on an old 601 based PowerMac 7200.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We forgot to remove the clock_gettime, clock_getres and get_tbfreq vDSO
calls on CPUs that have no timebase such as 601 or 403 (old CPUs that have
different mechanisms and for which the vDSO code will not work properly).
This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
find_victim can dereference a NULL pointer when iterating over the list
of victim spus because list_mutex only guarantees spu->ct to be stable,
but of course not to be non-NULL.
Also fix find_victim to not call spu_unbind_context without list_mutex
because that violates the above guarantee.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This saves 4k on non pSeries builds (except for iSeries where it saves
almost 4k).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson pointed out that swapper_pg_dir actually need to be
PGD_TABLE_SIZE bytes long not PAGE_SIZE. This actually saves 64k in
the bss for a kernel ppc64_defconfig built with CONFIG_PPC_64K_PAGES.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It is just a C char array, so declare it thusly.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Create a helper function (alloc_maybe_bootmem) that is marked __init_refok
to limit the chances of mistakenly referring to other __init routines.
WARNING: vmlinux.o(.text+0x2a9c4): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.update_dn_pci_info' and '.pci_dn_reconfig_notifier')
WARNING: vmlinux.o(.text+0x36430): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.mpic_msi_init_allocator' and '.find_ht_magic_addr')
WARNING: vmlinux.o(.text+0x5e804): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.celleb_setup_phb' and '.celleb_fake_pci_write_config')
WARNING: vmlinux.o(.text+0x5e8e8): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.celleb_setup_phb' and '.celleb_fake_pci_write_config')
WARNING: vmlinux.o(.text+0x5e968): Section mismatch: reference to .init.text:.__alloc_bootmem (between '.celleb_setup_phb' and '.celleb_fake_pci_write_config')
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Low-power mode implementation for Lite5200b.
Some I/O registers are also saved here.
A recent U-Boot that supports this (lite5200b_PM_config) is needed.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds DEFINE_SPUFS_ATTRIBUTE(), a wrapper around
DEFINE_SIMPLE_ATTRIBUTE which does the specified locking for the get
routine for us.
Unfortunately we need two get routines (a locked and unlocked version) to
support the coredump code. This hides one of those (the locked version)
inside the macro foo.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the spu coredump code doesn't respect the ulimit, it should.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rework spufs_coredump_extra_notes_write() to check for and return errors.
If we're coredumping to a pipe we can't trust file->f_pos, we need to
maintain the foffset value passed to us. The cleanest way to do this is
to have the low level write routine increment foffset when we've
successfully written.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To start with, arch_notes_size() etc. is a little too ambiguous a name for
my liking, so change the function names to be more explicit.
Calling through macros is ugly, especially with hidden parameters, so don't
do that, call the routines directly.
Use ARCH_HAVE_EXTRA_ELF_NOTES as the only flag, and based on it decide
whether we want the extern declarations or the empty versions.
Since we have empty routines, actually use them in the coredump code to
save a few #ifdefs.
We want to change the handling of foffset so that the write routine updates
foffset as it goes, instead of using file->f_pos (so that writing to a pipe
works). So pass foffset to the write routine, and for now just set it to
file->f_pos at the end of writing.
It should also be possible for the write routine to fail, so change it to
return int and treat a non-zero return as failure.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Because spufs might be built as a module, we can't have other parts of the
kernel calling directly into it, we need stub routines that check first if the
module is loaded.
Currently we have two structures which hold callbacks for these stubs, the
syscalls are in spufs_calls and the coredump calls are in spufs_coredump_calls.
In both cases the logic for registering/unregistering is essentially the same,
so we can simplify things by combining the two.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SPUFS attribute get routines take a void * because the generic attribute
code doesn't know what sort of data it's passing around.
However our internal __spufs_get_foo() routines can take a spu_context *
directly, which saves plonking it in and out of a void * again.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The spufs_coredump_read array is NULL terminated, and we also store the size.
We only need one or the other, and the other arrays in file.c are NULL
terminated, so do that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
