This Patch add the device information for the
MIC-3620 8-port RS-232 cPCI card from Advantech Co. Ltd.
Signed-off-by: Michael Bramer <grisu@deb-support.de>
Signed-off-by: Alan Cox <number6@the-village.bc.nu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function jsm_remove_one is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alan Cox <number6@the-village.bc.nu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__tty_open could return (to userspace) holding the tty_mutex thanks to a
regression introduced by 4a2b5fddd5 ("Move
tty lookup/reopen to caller").
This was found by bisecting an fsfuzzer problem. Admittedly I have no
idea how it managed to tickle this 100% reliably, but it is clearly a
regression and when hit leaves the box in a completely unusable state.
This patch lets the fsfuzzer test complete every time.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a new ioctl UBI_IOCSETPROP to set properties
on a volume. Also add the first property:
UBI_PROP_DIRECT_WRITE, this property is used to set the
ability to use direct writes in userspace
Signed-off-by: Sidney Amani <seed@uffs.org>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When data CRC checking is disabled, UBIFS returns incorrect return
code from the 'try_read_node()' function (0 instead of 1, which means
CRC error), which make the caller re-read the data node again, but using
a different code patch, so the second read is fine. Thus, we read the
same node twice. And the result of this is that UBIFS is slower
with no_chk_data_crc option than it is with chk_data_crc option.
This patches fixes the problem.
Reported-by: Reuben Dowle <Reuben.Dowle@navico.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP 2510p that uses the ata_piix driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP nx6325 that uses the sata_sil driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP nx6310 that uses the AHCI driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce new libata flags ATA_FLAG_NO_POWEROFF_SPINDOWN and
ATA_FLAG_NO_HIBERNATE_SPINDOWN that, if set, will prevent disks from
being spun off during system power off and hibernation, respectively
(to handle the hibernation case we need the new system state
SYSTEM_HIBERNATE_ENTER that can be checked against by libata, in
analogy with SYSTEM_POWER_OFF).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information. However, only the on-board controlles should
be blacklisted and their PCI slot numbers can be used for this
purpose. Unfortunately the existing interface for checking DMI
information of the system is not very convenient for this purpose,
because to use it, we would have to define special callback functions
or create a separate struct dmi_system_id table for each blacklisted
system.
To overcome this difficulty introduce a new function
dmi_first_match() returning a pointer to the first entry in an array
of struct dmi_system_id elements that matches the system DMI
information. Then, we can use this pointer to access the entry's
.driver_data field containing the additional information, such as
the PCI slot number, allowing us to do the desired blacklisting.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce boolean function system_entering_hibernation() returning
'true' during the last phase of hibernation, in which devices are
being put into low power states and the sleep state (for example,
ACPI S4) is finally entered.
Some device drivers need such a function to check if the system is
in the final phase of hibernation. In particular, some SATA drivers
are going to use it for blacklisting systems in which the disks
should not be spun down during the last phase of hibernation (the
BIOS will do that anyway).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver has been tested without the call to set_irq_type at this
point and occurs to work fine, so it should be safe to remove it.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The 5329 ColdFire peripheral IO register addresses are not relative to
the MBAR register. So fix the serial platform setup array and IRQ acking
to use just the direct addresses.
Signed-off-by: Matt Waddel <Matt.Waddel@freescale.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
This patch adds the name of the process to the bad allocation error
message on non-MMU systems.
Changed suggested by jsujjavanich@syntech-fuelmaster.com
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Make restart blocks working, required for proper syscall restarting.
Derived from same changes for m68k arch by Andreas Schwab <schwab@suse.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer said about this board:
Only ever a handful where made, and that was in 1999.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
m68knommu does not set the Kconfig NO_DMA variable, but also does
not provide the required functions, resulting in the following
build error triggered by commit a40c24a133
(net: Add SKB DMA mapping helper functions.):
<-- snip -->
..
LD vmlinux
net/built-in.o: In function `skb_dma_unmap':
(.text+0xac5e): undefined reference to `dma_unmap_single'
net/built-in.o: In function `skb_dma_unmap':
(.text+0xac7a): undefined reference to `dma_unmap_page'
net/built-in.o: In function `skb_dma_map':
(.text+0xacdc): undefined reference to `dma_map_single'
net/built-in.o: In function `skb_dma_map':
(.text+0xace8): undefined reference to `dma_mapping_error'
net/built-in.o: In function `skb_dma_map':
(.text+0xad10): undefined reference to `dma_map_page'
net/built-in.o: In function `skb_dma_map':
(.text+0xad82): undefined reference to `dma_unmap_page'
net/built-in.o: In function `skb_dma_map':
(.text+0xadc6): undefined reference to `dma_unmap_single'
make[1]: *** [vmlinux] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix cache flushing for the 527x ColdFire processors
Its CACR register format is slightly different.
Along with this add support for flushing the 523x cache, which uses
the same format as the 527x ColdFire's, and was missing flush support.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
I noticed (the hard way) that the mcf.c driver doesn't support the fractional precision register on the MCF5272. This makes the console dicey at 115200 baud and a system clock of 66.0 MHz. On the other hand, if your hardware is running at 66.666 MHz, it probably isn't a problem.
Patch submitted by John Adamson <jadamson@allen-organ.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Part of the code that did not make sense to me got removed by Greg.
This is part two:
The first compare is to check whether the interrupts are disabled or not.
Depending on the result we exectute the RESTORE_ALL macro is not only
restoring the stack but also returning to caller.
The test for pending softirq has been removed because it is allready done
in irq_exit().
Since system_call() is allso using the SAVE_ALL macro and returning via
ret_from_exception label I see no reason why we could not do this here
as well. This is also handy because if we return from the timer interrupt
and we need to resched than we check for this :)
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Freeze activity when notified that the underlying chip
is getting reset on a EEH event or fatal error.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set up a notification mechanism to inform upper layer modules
(iWARP, iSCSI) of a chip reset due to an EEH event or a fatal error.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_splice_data_recv has two lengths to consider: the len parameter it
gets from tcp_read_sock, which specifies the amount of data in the skb,
and rd_desc->count, which is the amount of data the splice caller still
wants. Currently it passes just the latter to skb_splice_bits, which then
splices min(rd_desc->count, skb->len - offset) bytes.
Most of the time this is fine, except when the skb contains urgent data.
In that case len goes only up to the urgent byte and is less than
skb->len - offset. By ignoring len tcp_splice_data_recv may a) splice
data tcp_read_sock told it not to, b) return to tcp_read_sock a value > len.
Now, tcp_read_sock doesn't handle used > len and leaves the socket in a
bad state (both sk_receive_queue and copied_seq are bad at that point)
resulting in duplicated data and corruption.
Fix by passing min(rd_desc->count, len) to skb_splice_bits.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its a valid use case to have null associated data in a ccm vector, but
this case isn't being handled properly right now.
The following ccm decryption/verification test vector, using the
rfc4309 implementation regularly triggers a panic, as will any
other vector with null assoc data:
* key: ab2f8a74b71cd2b1ff802e487d82f8b9
* iv: c6fb7d800d13abd8a6b2d8
* Associated Data: [NULL]
* Tag Length: 8
* input: d5e8939fc7892e2b
The resulting panic looks like so:
Unable to handle kernel paging request at ffff810064ddaec0 RIP:
[<ffffffff8864c4d7>] :ccm:get_data_to_compute+0x1a6/0x1d6
PGD 8063 PUD 0
Oops: 0002 [1] SMP
last sysfs file: /module/libata/version
CPU 0
Modules linked in: crypto_tester_kmod(U) seqiv krng ansi_cprng chainiv rng ctr aes_generic aes_x86_64 ccm cryptomgr testmgr_cipher testmgr aead crypto_blkcipher crypto_a
lgapi des ipv6 xfrm_nalgo crypto_api autofs4 hidp l2cap bluetooth nfs lockd fscache nfs_acl sunrpc ip_conntrack_netbios_ns ipt_REJECT xt_state ip_conntrack nfnetlink xt_
tcpudp iptable_filter ip_tables x_tables dm_mirror dm_log dm_multipath scsi_dh dm_mod video hwmon backlight sbs i2c_ec button battery asus_acpi acpi_memhotplug ac lp sg
snd_intel8x0 snd_ac97_codec ac97_bus snd_seq_dummy snd_seq_oss joydev snd_seq_midi_event snd_seq snd_seq_device snd_pcm_oss snd_mixer_oss ide_cd snd_pcm floppy parport_p
c shpchp e752x_edac snd_timer e1000 i2c_i801 edac_mc snd soundcore snd_page_alloc i2c_core cdrom parport serio_raw pcspkr ata_piix libata sd_mod scsi_mod ext3 jbd uhci_h
cd ohci_hcd ehci_hcd
Pid: 12844, comm: crypto-tester Tainted: G 2.6.18-128.el5.fips1 #1
RIP: 0010:[<ffffffff8864c4d7>] [<ffffffff8864c4d7>] :ccm:get_data_to_compute+0x1a6/0x1d6
RSP: 0018:ffff8100134434e8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8100104898b0 RCX: ffffffffab6aea10
RDX: 0000000000000010 RSI: ffff8100104898c0 RDI: ffff810064ddaec0
RBP: 0000000000000000 R08: ffff8100104898b0 R09: 0000000000000000
R10: ffff8100103bac84 R11: ffff8100104898b0 R12: ffff810010489858
R13: ffff8100104898b0 R14: ffff8100103bac00 R15: 0000000000000000
FS: 00002ab881adfd30(0000) GS:ffffffff803ac000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff810064ddaec0 CR3: 0000000012a88000 CR4: 00000000000006e0
Process crypto-tester (pid: 12844, threadinfo ffff810013442000, task ffff81003d165860)
Stack: ffff8100103bac00 ffff8100104898e8 ffff8100134436f8 ffffffff00000000
0000000000000000 ffff8100104898b0 0000000000000000 ffff810010489858
0000000000000000 ffff8100103bac00 ffff8100134436f8 ffffffff8864c634
Call Trace:
[<ffffffff8864c634>] :ccm:crypto_ccm_auth+0x12d/0x140
[<ffffffff8864cf73>] :ccm:crypto_ccm_decrypt+0x161/0x23a
[<ffffffff88633643>] :crypto_tester_kmod:cavs_test_rfc4309_ccm+0x4a5/0x559
[...]
The above is from a RHEL5-based kernel, but upstream is susceptible too.
The fix is trivial: in crypto/ccm.c:crypto_ccm_auth(), pctx->ilen contains
whatever was in memory when pctx was allocated if assoclen is 0. The tested
fix is to simply add an else clause setting pctx->ilen to 0 for the
assoclen == 0 case, so that get_data_to_compute() doesn't try doing
things its not supposed to.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When we get left-over bits from a slow walk, it means that the
underlying cipher has gone troppo. However, as we're handling
that case we should ensure that the caller terminates the walk.
This patch does this by setting walk->nbytes to zero.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Reported-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
drivers/net/r6040.c:441: warning: unused variable 'pdev'
Signed-off-by: Manish Katiyar <mkatiyar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 9088c56095
(udp: Improve port randomization) introduced a regression for UDP bind() syscall
to null port (getting a random port) in case lot of ports are already in use.
This is because we do about 28000 scans of very long chains (220 sockets per chain),
with many spin_lock_bh()/spin_unlock_bh() calls.
Fix this using a bitmap (64 bytes for current value of UDP_HTABLE_SIZE)
so that we scan chains at most once.
Instead of 250 ms per bind() call, we get after patch a time of 2.9 ms
Based on a report from Vitaly Mayatskikh
Reported-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Tested-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc911x_set_multicast_list currently performs the only non-atomic
read-modify-write of INT_EN. This patch permanently enables the
RXSTOP_INT interrupt, and changes the ISR to only conditionally run the
multicast filter workaround code.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the smc91x driver to use struct net_device_ops.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan pointed that using PDE_NET outside the
proc code is plain bogus (thanks Alexey!). Fix it.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PDE_NET usage in driver code is a sign and, indeed, switching
to seq_open_net/seq_release_net saves code and fixes bogus things, like
user triggerabble BUG_ON(!net) after maybe_get_net, and NULLifying ->private.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incoming packets and sockets are already gone.
The netdevice notifier is unregistered under the RTNL lock
There remains a race with the rtnetlink handlers unregistration, but it
is a generic RTNL issue that was already present before this change.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this fix, virtio_net makes incorrect usage of scatterlists. It sets
the end of the scatterlist chain after the first element, despite the fact
that more entries come after it.
If you try to run dma_map_sg() on one of the scatterlists given to you by
add_buf(), you will get a null pointer oops.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
And support for the KX/KX4 mezzanine card. Device id 0x10B6.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load times for NICs that use i2c to communicate with the phy were taking
~4.5 sec per port. This fix first checks to see if the link is already
up before calling get_link_capabilities, since if it is we don't need
query the phy for link state.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
