Let the ASoC core take care of registering the DAPM widget and routes as well as
the controls. This makes the code a bit shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
ADAU1707_CLKDIV_UNSET is always compared against an unsigned int and
not an unsigned long. The current tests are always false.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use snd_soc_dapm_mixer_update_power() instead of reimplementing its
functionality.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Both the adau1702 and the adau1401(a) are register compatible to the adau1701,
so add them to adau1701 driver's device id table.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The adau1701 driver was removed from SND_SOC_ALL_CODECS in commit commit ee8c7e9
("ASoC: Remove adau1701 from SND_SOC_ALL_CODECS due to Sigma dependency") due
to the dependency on the SigmaDSP firmware loader which was only available on a
limited set of platforms. This was fixed quite some time ago in commit 40216ce7
("ASoC: Move SigmaDSP firmware loader to ASoC") though, so we can add the driver
back again to SND_SOC_ALL_CODECS.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The accessory detect debounce work is not performance sensitive so let
the scheduler run it wherever is most efficient rather than in a per CPU
workqueue by using the system power efficient workqueue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The accessory detect debounce work is not performance sensitive so let
the scheduler run it wherever is most efficient rather than in a per CPU
workqueue by using the system power efficient workqueue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
The usage of strict_strto*() is not preferred, because
strict_strto*() is obsolete. Thus, kstrto*() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently after playing any audio file, we get the following error message:
$ aplay clarinet.wav
Playing WAVE 'clarinet.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
$ wm8962 0-001a: Unsupported sysclk ratio 544
This error message appears about 5 seconds after the audio playback has
finished.
Quoting Mark Brown [1]:
"The issue here is triggered by the machine
switching from the FLL to direct MCLK usage where the MCLK isn't
generating a useful ratio.
I suspect we should just kill the configure_bclk() in set_sysclk(), that
one isn't safe as we can't reconfigure a live SYSCLK and it's probably
the one that generates your warnings."
Confirmed that the "Unsupported sysclk ratio" error message comes from
wm8962_set_dai_sysclk(), so get rid of wm8962_configure_bclk() inside this
function.
[1] http://mailman.alsa-project.org/pipermail/alsa-devel/2013-July/064241.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The accessory detect debounce work is not performance sensitive so let
the scheduler run it wherever is most efficient rather than in a per CPU
workqueue by using the system power efficient workqueue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The work used to allow the capcitors to ramp is not performance sensitive
so let the scheduler run it wherever is most efficient rather than in a
per CPU workqueue by using the system power efficient workqueue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The accessory detect debounce work is not performance sensitive so let
the scheduler run it wherever is most efficient rather than in a per CPU
workqueue by using the system power efficient workqueue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The accessory detect debounce work is not performance sensitive so let
the scheduler run it wherever is most efficient rather than in a per CPU
workqueue by using the system power efficient workqueue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
None of the delayed work the driver schedules has particularly short delays
and it is not performance sensitive so let the scheduler run it wherever
is most efficient rather than in a per CPU workqueue by using the system
power efficient workqueue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
None of the delayed work the driver schedules has particularly short delays
and it is not performance sensitive so let the scheduler run it wherever
is most efficient rather than in a per CPU workqueue by using the system
power efficient workqueue.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Devices like mobilephones, computers are typically used as
HDMI sources, but devices like TV, navigators will be HDMI
sinks.
for auto scenerios, In-Vehicle Infotainment(IVI) can be HDMI
sink to display movies from mobilephones.
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It's not always the case that clock is already available when sgtl5000
get probed at the first time, e.g. the clock is provided by CPU DAI
which may be probed after sgtl5000. So let's defer the probe when
devm_clk_get() call fails and give it chance to try later.
It fixes the regression on imx28 since commit 9e13f34 (ASoC: sgtl5000:
Let the codec acquire its clock).
[ 1.927637] sgtl5000 0-000a: Failed to get mclock: -2
[ 1.934280] sgtl5000: probe of 0-000a failed with error -2
[ 1.945906] mxs-sgtl5000 sound.13: ASoC: CODEC (null) not registered
[ 1.953787] mxs-sgtl5000 sound.13: snd_soc_register_card failed (-517)
[ 1.960865] platform sound.13: Driver mxs-sgtl5000 requests probe deferral
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver supports a range of devices but currently doesn't allow those
device names to be used for enumeration on DT. Add the currently listed
I2C IDs as compatible strings.
Signed-off-by: Mark Brown <broonie@linaro.org>
The registers of max98088 are 8 bits, not 16 bits. This bug causes the
contents of registers to be overwritten with bad values when the codec
is suspended and then resumed.
Signed-off-by: Chih-Chung Chang <chihchung@chromium.org>
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
sgtl5000 has 16-bit registers, and only even numbers are valid for its registers
addresses.
Let regmap knows about this feature by specifying the 'reg_stride' field, so
that it can access only the valid registers.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As well as being better style this allows the device to idle when there is
no audio card instantaited which is probably what we want.
Signed-off-by: Mark Brown <broonie@linaro.org>
This is better from a device model point of view since we don't try to
do things like instantiate the card until the required resources appear.
Signed-off-by: Mark Brown <broonie@linaro.org>
The version number has never been updated and the printk isn't based on
any interaction with the device.
Signed-off-by: Mark Brown <broonie@linaro.org>
The main function of the option is to enable compile testing. There is
still an option since COMPILE_TEST is intended to enable selection of
extra drivers rather than forcing them on.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When doing signal activity detection, the only output from the DRC will
often be a GPIO pin. This patch adds a signal activity output that is
activated when a GPIO is configured to output the DRC signal activity
detection.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Support for loading the ak4554 codec module via devicetree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ak4554 is very simple DA/AD converter which has no setting register.
Note that it has hard coded asymmetric data format
playback : SND_SOC_DAIFMT_RIGHT_J
capture : SND_SOC_DAIFMT_LEFT_J
This driver has single DAI and doesn't have set_fmt.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver can be built as module, thus add module device table for adav801 to
support module auto loading.
To make the naming consistent, also rename adav80x_id to adav80x_i2c_id.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
wm8978 needs .symmetric_rates = 1.
The playback/capture will be strange without this patch
when it used asymmetric rate in same time
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A few small fixes, all driver specific. The removal of the GPIO based
pinmuxing is a bug fix, since the obsolete nodes had been removed from
the DT it stopped the driver loading.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=+rVP
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v3.11
A few small fixes, all driver specific. The removal of the GPIO based
pinmuxing is a bug fix, since the obsolete nodes had been removed from
the DT it stopped the driver loading.
SGTL5000_PLL_FRAC_DIV_MASK is used to mask bits 0-10 (11 bits in total) of
register CHIP_PLL_CTRL, so fix the mask to accomodate all this bit range.
Reported-by: Oskar Schirmer <oskar@scara.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
According to the sgtl5000 reference manual, the default value of CHIP_SSS_CTRL
is 0x10.
Reported-by: Oskar Schirmer <oskar@scara.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
A relative calm release at this time with a flat diffstat.
The only significant change in the ALSA core side is the support for
more than 32 card instances, configurable via kconfig.
Other than that, in both ASoC and other parts, mostly some
improvements and fixes on the driver side.
- hda: More quirks for ALC269-variants on Dell & co, VIA codec fixes
- hda: Haswell HDMI audio fixes, runtime PM improvements
- hda: Intel BayTrail support, ALC5505 DSP support
- es1968: MediaForte M56VAP support
- usb-audio: Improved support for Yamaha/Roland devices
- usb-audio: M2Tech hiFace, Audio Advantage Micro II support
- hdspm: wordclock fixes
- ASoC: Pending fixes for WM8962
- ASoC: Cleanups and fixes for Blackfin, SGTL5000 and UX500
- ASoC: Generalisation of the Bluetooth and HDMI stub drivers
- ASoC: SSM2518 and RT5640 codec drivers.
- ASoC: Tegra CPUs with RT5640 machine driver
- ASoC: AC'97 refactoring bug fixes
- ASoC: ADAU1701 driver fixes
- Clean up of *_set_drvdata() in a wide range of drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=i5lT
-----END PGP SIGNATURE-----
Merge tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"A relative calm release at this time with a flat diffstat. The only
significant change in the ALSA core side is the support for more than
32 card instances, configurable via kconfig. Other than that, in both
ASoC and other parts, mostly some improvements and fixes on the driver
side.
- hda: More quirks for ALC269-variants on Dell & co, VIA codec fixes
- hda: Haswell HDMI audio fixes, runtime PM improvements
- hda: Intel BayTrail support, ALC5505 DSP support
- es1968: MediaForte M56VAP support
- usb-audio: Improved support for Yamaha/Roland devices
- usb-audio: M2Tech hiFace, Audio Advantage Micro II support
- hdspm: wordclock fixes
- ASoC: Pending fixes for WM8962
- ASoC: Cleanups and fixes for Blackfin, SGTL5000 and UX500
- ASoC: Generalisation of the Bluetooth and HDMI stub drivers
- ASoC: SSM2518 and RT5640 codec drivers.
- ASoC: Tegra CPUs with RT5640 machine driver
- ASoC: AC'97 refactoring bug fixes
- ASoC: ADAU1701 driver fixes
- Clean up of *_set_drvdata() in a wide range of drivers"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (284 commits)
ALSA: vmaster: Fix the regression of missing vmaster hook call
ALSA: hda - Add Dell SSID to support Headset Mic recording
ASoC: adau1701: remove control_data assignment
ASoC: adau1701: more direct regmap usage
ASoC: ac97: fixup multi-platform AC'97 module build failure
ASoC: pxa2xx: fixup multi-platform AC'97 build failures
ASoC: tegra20-ac97: Remove unused variable
ASoC: tegra20-ac97: Remove duplicate error message
ALSA: usb-audio: Add Audio Advantage Micro II
ASoC: tas5086: fix Mid-Z implementation
ASoC: tas5086: fix TAS5086_CLOCK_CONTROL register size
ALSA: Replace the magic number 44 with const
ALSA: hda - Fix the max length of control name in generic parser
ALSA: hda - Guess what, it's two more Dell headset mic quirks
ALSA: hda - Yet another Dell headset mic quirk
ALSA: hda - Add support for ALC5505 DSP power-save mode
ASoC: mfld: Remove unused variable
ALSA: usb-audio: add quirks for Roland QUAD/OCTO-CAPTURE
ALSA: usb-audio: claim autodetected PCM interfaces all at once
ALSA: usb-audio: remove superfluous Roland quirks
...
A few final updates:
- A couple of additional bug fixes for the AC'97 refactoring.
- Some fixes for the ADAU1701 driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ZS3l
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Final updates for v3.11
A few final updates:
- A couple of additional bug fixes for the AC'97 refactoring.
- Some fixes for the ADAU1701 driver.
