We didn't release the Rx AMPDU ressources properly.
This bug led to firmware assert after 16 BA sessions.
Cc: <stable@vger.kernel.org> [3.9+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Avoid creating VIF specific debugfs directory if already exist.
This may happen when, for example, resetting hw, suspend-resume.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Add sram dump on NIC error for debug improvement.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The LQ command argument isn't needed, it's always taken from the
station struct that's already passed, remove the argument.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
This was missing and prevented any further attempts
to load the module.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
5 and 10 MHz support needs to know the current operating channel width,
add the chandef to the rate control API.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
To improve power consumption in idle associated mode FW may lower
RX power. This low linearity mode is acceptable for listening low rate
RX such as beacons and groupcast. The driver enables LPRX only if PM
is enabled and associated AP's beacon TX rate is 1Mbps or 6Mbps.
LPRX RSSI threshold is used to limit a range where LPRX is applied.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case that an AP/GO interface is started while there is a
station/P2P client associated, need to make sure that the AP/GO
beacon time is far enough from the station's one in oder to allow
the station to receive the DTIM beacons and the following traffic
etc.
To resolve this, when the AP is started, check if there is an
active station interface, and guarantee that the AP/GO TBTT is far
enough from the station one.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add prints visible to the user when entering and exiting
thrermal throttling, because so users can tell that the
NIC is getting too hot (and throughput will decrease.)
Signed-off-by: eytan lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1x1 products will need a special LUT.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The old nl80211 testmode is no longer useful in iwlwifi,
we're moving towards a new model internally and there's
no open tool to use it, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If someone wants to disable AMPDU, there is the 11n_disable
module parameter.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the D3 firmware crashes, it can be helpful for debugging to
resume the system to get the SRAM snapshot to see why it crashed.
Allow enabling this with a debugfs option.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The fw is unreliable in all the cases in which the packet
wasn't sent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Give the scratch area a sub structure so it's marked
explicitly and it is obvious which part it is.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the unused iwl_mvm *mvm parameter from the
iwl_mvm_send_remote_wake_cfg function in D3.c.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since driver does not use control.rates[0].count, we have never set that
variable. But currently, after rate control API rewrite, this is required
by mac80211. Otherwise legacy rates control does not work and we transmit
always at 1Mbit/s on pre 11n networks.
[same fix as for iwlegacy, thanks Stanislaw!]
Signed-off-by: Moshe Benji <Moshe.Benji@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlmvm does not support concurrent operation of AP with P2P Client/GO.
Update the interface limits to reflect that iwlmvm supports only
concurrent operation of station with AP and P2P Client/GO.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The MCAST queue should be enabled after DTIM only.
According to fw API, the MCAST must not be attached to any
station, but should appear in the mcast_qid of the AP's
mac context only.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware API wasn't being used correctly, fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code moved and is now far away from the code that takes
the mutex.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently beacon availability upon association is marked by have_beacon
flag of assoc_data structure that becomes unavailable when association
completes. However beacon availability indication is required also after
association to inform a driver. Currently dtim_period parameter is used
for this purpose. Move have_beacon flag to another structure, persistant
throughout a interface's life cycle. Use suitable sematics for beacon
availability indication.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[fix another instance of BSS_CHANGED_DTIM_PERIOD in docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Thermal Throttling code could do that, fix it.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In multicast, there is no retries nor RTS since there is no
specific recipient that can ACK or send CTS. This means
that we must not use the rate scale table for multicast
frames.
This true for any frame that doesn't have a valid
ieee80211_sta pointer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In unassociated BSS STA mode FW verifies both power save and power
management flags to decide on switching power off. The driver currently
sets power management flag according to mac80211 decision. As result, in
unassociated mode power management flag is down and power consumption is
high. Change power management enablement. When unassociated in BPS and
LP power save modes enable power management regardless of mac80211
decision. Rely on mac80211 decision if associated. Add power management
state update during associated/disassociated modes transitions.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently vif_count verification for power management enablement appear
in different places. Move these verifications to one place in
iwl_mvm_update_power_mode().
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The AP mode needs to use the MCAST fifo for the MCAST
frames sent after the DTIM. This fifo needs to be
configured with the same parameters as the VOICE FIFO.
A separate SCD queue is mapped to this fifo - the cab_queue
(cab stands for Content After Beacon). This queue isn't
connected to any station, but rather to the MAC context.
This queue should (and is already) be set as the MCAST
queue - this is part of the of MAC context command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since SCAN related handlers are much less likely than
beacon related handlers, reorder between them.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to the FW implementation, the quota command should
have a valid entry for each active binding (where 'active' in
this context means that the binding is known to the FW). In case
the binding should not get any quota, the 'quota' should be set
to zero.
Not setting an 0 quota for an active binding when all the MACs
in the binding are idle, i.e., not associated in case of managed
interface, will result in preventing the FW scheduler from entering
IDLE state and the FW from transitioning to low PS.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Somehow, the Tx flags for BAR were completely wrong.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Another step in the rate control / BT Coex integration
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This holds for existing BA agreements.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There was a typo in the Loose LUT for BT Coex.
Fix that.
Reported-by: Roi Cohen <roi.cohen@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge to get the wil6210 changes that a cfg80211 change needs.
A conflict in drivers/net/wireless/ath/ath9k/init.c was just
whitespace changes.
Also fix a semantic conflict due to cw1200 using WoWLAN which
I had modified in my tree.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit eebfc9394e.
This wasn't intended to be included here, my mistake. I
accidentally merged a mac80211 fixes tree here that had
this change, when it wasn't even intended to be there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For testing the D3 (WoWLAN) firmware, it is useful to be able
to run the firmware with instrumentation while the host isn't
sleeping and can poke at the firmware debug logging etc.
Implement this by a debugfs file. When the file is opened the
D3 firmware is loaded and all regular commands are blocked.
While the file is being read, poll the firmware's PME status
flag and report EOF once it changes to non-zero. When it is
closed, do (most of) the resume processing. This lets a user
just "cat" the file. Pressing Ctrl-C to kill the cat process
will resume the firwmare as though the platform resumed for
non-wireless reason and when the firmware wants to wake up
reading from the file automatically completes.
Unlike in real suspend, only disable interrupts and don't
reset the TX/RX hardware while in the test mode. This is a
workaround for some interrupt problems that happen only when
the PCIe link isn't fully reset (presumably by changing the
PCI config space registers which the core PCI code does.)
Note that while regular operations are blocked from sending
commands to the firmware, they could still be made and cause
strange mac80211 issues. Therefore, while using this testing
feature you need to be careful to not try to disconnect, roam
or similar, and will see warnings for such attempts.
Als note that this requires an upcoming firmware change to
tell the driver the location of the PME status flag in SRAM.
D3 test will fail if the firmware doesn't report the pointer.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
