The previous patch ("input/ti_am335x_tsc: ACK the HW_PEN irq in ISR")
acked the interrupt so we don't freeze if we don't handle an enabled
interrupt source. The interrupt core has a mechanism for this and to get
it work one should only say that it handled an interrupt if it is
actually the case.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The interrupt source IRQENB_HW_PEN is enabled in suspend and suposed to
be used as a wake up source. Once this interrupt source is unmaksed, the
devices ends up in ISR and never continues.
This change ACKs the interrupt and disables it so the system does not
freeze.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The driver programs a threshold of "coordinate_readouts" say 5. The
REG_FIFO0THR registers says it should it be programmed to "threshold
minus one". The driver does not expect just 5 coordinates but 5 * 2 + 2.
Multiplied by two because 5 for X and 5 for Y and plus 2 because we have
two Z.
The whole thing kind of works because It reads the 5 coordinates for X
and Y from FIFO0 and FIFO1 and the last element in each FIFO is ignored
within the loop and read later.
Nothing guaranties that FIFO1 is ready by the time it is read. In fact I
could see that that FIFO1 reaturns for Y channels 8,9, 10, 12, 6 and for
Y channel 7 for Z. The problem is that channel 7 and channel 12 got
somehow mixed up.
The other Problem is that FIFO1 is also used by the IIO part leading to
wrong results if both (tsc & adc) are used.
The patch tries to clean up the whole thing a little:
- Remove the +1 and -1 in REG_STEPCONFIG, REG_STEPDELAY and its counter
part in the for loop. This is just confusing.
- Use only FIFO0 in TSC. The fifo has space for 64 entries so should be
fine.
- Read the whole FIFO in one function and check the channel.
- in case we dawdle around, make sure we only read a multiple of our
coordinate set. On the second interrupt we will cleanup the remaining
enties.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
This patch removes access to platform data mfd_tscadc_board because the
platform is DT only.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
This patch adds DT support to touch driver. It also provides a binding
document which is used by the MFD and IIO part of the device.
This patch also renames steps_to_configure to coordinate_readouts
because the original name misleads the purpose of the variable.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
When touchscreen and ADC are used together, this
unwanted fifo flush leads to loss of ADC data.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The current driver expected touchscreen input
wires(XP,XN,YP,YN) to be connected in a particular order.
Making changes to accept this as platform data.
Sebastian reworked the original patch and removed a lot of the not
required pieces.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Current code has hard coded value written to
step enable bits. Now the bits are updated based
on how many steps are needed to be configured got
from platform data.
The user needs to take care not to exceed
the count more than 16. While using ADC and TSC
one should take care to set this parameter correctly.
Sebastian added the common lock and moved the code, that manipulates the
steps, from into the mfd module.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The mfd driver creates platform data for the child devices and it is the
ti_tscadc_dev struct. This struct is copied for the two devices.
The copy of the structure makes a common lock in this structure a little
less usefull. Therefore the platform data is not a pointer to the
structure and the same structure is used.
While doing the change I noticed that the suspend/resume code assumes
the wrong pointer for ti_tscadc_dev and this has been fixed as well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
If pdata is NULL, atmel_tsadcc_probe() will release all the resources
and return 0, but we need a error code is returned in this case.
Fix to return -EINVAL and move the check for pdata to the begin
of this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The command and status register in the driver were swapped with
respect to the order specified in the datasheet (CY8CTMA140).
Confirmed with Cypress that the order in the datasheet is correct.
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For the devices that has blocking with timeout communication, these
extra handshakes will prevent one timeout delay in startup sequence
Tested-by: Ferruh Yigit <fery@cypress.com> on TMA300-DVK
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
memcpy param is wrong because of offset in bl_cmd, this may corrupt the
stack which may cause a crash.
Tested-by: Ferruh Yigit <fery@cypress.com> on TMA300-DVK
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The usage of devm_* functions makes code cleaner and tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The egalax_ts touchscreen modul not report ABS_MT_POSITION_Y proper.
As result it may be, that upper software levels only receive x coordinates well.
Signed-off-by: Heiko Abraham <abrahamh@web.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We add the possibility to hand over a GPIO number for the reset pin.
This way we can remove existing board code that takes care of it and
group this information properly in the platform data or in the device
tree configuration.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
kfree on a null pointer is a no-op. Hence null check is not
necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch converts the drivers to use the
module_platform_driver_probe() macro which makes the code smaller and
a bit simpler.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRRkrbAAoJEHm+PkMAQRiGy3oH/jrbHinYs0auurANgx4TdtWT
/WNajstKBqLOJJ6cnTR7sOqwOVlptt65EbbTs+qGyZ2Z2W/Lg0BMenHvNHo4ER8C
e7UbMdBCSLKBjAMKh1XCoZscGv4Exm8WRH3Vc5yP0Hafj3EzSAVLY1dta9WKKoQi
bh7D1ErUlbU1zczA1w5YbPF0LqFKRvyZOwebMCCAKAxv5wWAxmbcPNxVR4sufkjg
k6TkQ2ysgWivZAfy3tJYOcxiEu7ahpZVEuYdlZEJQXHRQUfoNljQlOp4BqKsYUai
5A0kaf2VpKay/7pkhvTfBBcF/jFJ68pYP6gQ2ThNdr0b5kOiAfMWj030Xyngnhg=
=iO9t
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc3' into next
Merge with mainline to bring in module_platform_driver_probe() and
devm_ioremap_resource().
dev_dbg should end with a new line.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Often a reading can be wrong. This patch assures that this is really a
pen up event and not a false reading.
Based on wm9712: pen up by Teresa Gámez and Christian Hemp.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of interpreting a wrong measurement as pen up, we should
try to read again.
Based on wm9712: pen up by Teresa Gámez and Christian Hemp.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With fast movements, there occured some out of screen jumps with my
touchscreen. The abs_x and abs_y module parameters should fix this by
default, but the driver doesn't actively checks the x/y coordinates.
Instead it seems that the input layer was supposed to drop out of range
inputs, as described in the comments:
"These parameters are used to help the input layer discard out of
range readings and reduce jitter etc"
The input layer documentation describes that values that are not in the
absolute range are also accepted.
So this patch adds a check within the driver.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Except for the largish change to the ALPS driver adding "Dolphin V1"
support and Wacom getting a new signature of yet another device, the
rest are straightforward driver fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: mms114 - Fix regulator enable and disable paths
Input: ads7864 - check return value of regulator enable
Input: tc3589x-keypad - fix keymap size
Input: wacom - add support for 0x10d
Input: ALPS - update documentation for recent touchpad driver mods
Input: ALPS - add "Dolphin V1" touchpad support
Input: ALPS - remove unused argument to alps_enter_command_mode()
Input: cypress_ps2 - fix trackpadi found in Dell XPS12
When it uses regulators the mms114 driver checks to see if it managed to
acquire regulators and ignores errors. This is not the intended usage and
not great style in general.
Since the driver already refuses to probe if it fails to allocate the
regulators simply make the enable and disable calls unconditional and
add appropriate error handling, including adding cleanup of the
regulators if setup_reg() fails.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At least print a warning if we can't power the device up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is a more complete atmel patch-series out by Nick Dyer that fixes
this and other things, but in the meantime this is the minimal thing to
get the touchscreen going on (at least my) Pixel Chromebook.
Not that I want my dirty fingers near that beautiful screen, but it
seems that a non-initialized touchscreen will also end up being a
constant wakeup source, so you have to disable it to go to sleep. And
it's easier to just fix the initialization sequence.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This same driver can be used by atmel based touchscreens and touchpads
(buttonpads). Platform data may specify a device is a touchpad
using the is_tp flag.
This will cause the driver to perform some touchpad specific
initializations, such as:
* register input device name "Atmel maXTouch Touchpad" instead of
Touchscreen.
* register BTN_LEFT & BTN_TOOL_* event types.
* register axis resolution (as a fixed constant, for now)
* register BUTTONPAD property
* process GPIO buttons using reportid T19
Input event GPIO mapping is done by the platform data key_map array.
key_map[x] should contain the KEY or BTN code to send when processing
GPIOx from T19. To specify a GPIO as not an input source, populate
with KEY_RESERVED, or 0.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the necessary code to create the needed platformdata from devicetree
informations.
The interrupt mode of the chip is not set via devicetree, as it is not
a property of the hardware but instead only a preferred type of operation.
This should probably be made settable via configfs in the future.
The option set as default is the mode the datasheet mentions as default.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When supporting devicetree the platformdata may not necessarily come
from the dev but may be generated in the driver instead.
Therefore keep the pointer in the driver struct instead of using
dev.platform_data.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Devicetree based platforms don't handle device callbacks very well
and until now no board has come along that needs more extended hwinit
than pulling the rst gpio high.
Therefore pull the reset handling directly into the driver and remove
the callbacks from the driver.
If extended device setup is needed at some later point, power-sequences
would probably be the solution of choice.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Previously the gpio was not configured at all.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Two new touchpad drivers - Cypress APA I2C Trackpad and Cypress PS/2
touchpad and a big update to ALPS driver from Kevin Cernekee that adds
support for "Rushmore" touchpads and paves way for adding support for
"Dolphin" touchpads.
There is also a new input driver for Goldfish emulator and also
Android keyreset driver was folded into SysRq code.
A few more drivers were updated with device tree bindings and others
got some small cleanups and fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (55 commits)
Input: cyttsp-spi - remove duplicate MODULE_ALIAS()
Input: tsc2005 - add MODULE_ALIAS
Input: tegra-kbc - require CONFIG_OF, remove platform data
Input: synaptics - initialize pointer emulation usage
Input: MT - do not apply filtering on emulated events
Input: bma150 - make some defines public and fix some comments
Input: bma150 - fix checking pm_runtime_get_sync() return value
Input: ALPS - enable trackstick on Rushmore touchpads
Input: ALPS - add support for "Rushmore" touchpads
Input: ALPS - make the V3 packet field decoder "pluggable"
Input: ALPS - move pixel and bitmap info into alps_data struct
Input: ALPS - fix command mode check
Input: ALPS - rework detection of Pinnacle AGx touchpads
Input: ALPS - move {addr,nibble}_command settings into alps_set_defaults()
Input: ALPS - use function pointers for different protocol handlers
Input: ALPS - rework detection sequence
Input: ALPS - introduce helper function for repeated commands
Input: ALPS - move alps_get_model() down below hw_init code
Input: ALPS - copy "model" info into alps_data struct
Input: ALPS - document the alps.h data structures
...
