Enabling twl4030_wdt and twl4030_pwrbutton only for Triton i.e for
TWL4030 and TWL5030. This is to be excluded for Phoenix TWL6030.
Tested OMAP4 blaze, OMAP2430, OMAP3630 boot up.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ensure that the chip is in the lowest power mode possible when suspended
by performing a soft reset on it. On early silicon revisions the lowest
power modes can't be entered without using reset so we can't achieve
equivalent results within the individual drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In Blaze and Panda, 32KHz clock - CLK32KG to WLAN is supplied
from Phoenix TWL6030.
Add CLK32KG platform data to blaze and omap4panda board file.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In OMAP4 Blaze and Panda, 32KHz clock to WLAN is supplied from Phoenix
TWL6030. The 32KHz clock state (ON/OFF) is configured in
CLK32KG_CFG_[GRP, TRANS, STATE] register. This follows the same register
programming model as other regulators in TWL6030. So add CLK32KG as pseudo
regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a pretty straight-forward system control driver for the
AB8500. This driver will be used from the core platform, e.g the
clock tree implementation in the machine code, and is by nature
singleton.
There are a few simple functions to read, write, set and clear
registers so that the machine code can control its own foundation.
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x interrupt controller provides reporting of the touchscreen
related interrupts in the primary interrupt status register as a
performance optimisation - use this to avoid reading the secondary
status registers for those interrupts.
For code simplicity and to avoid iterating over all interrupts we open
code for the two affected interrupt sources.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is a move to deprecate bus-specific PM operations and move to
using dev_pm_ops instead in order to reduce the amount of boilerplate
code in buses and facilitiate updates to the PM core. Do this move for
the WM831x SPI driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When using a fixed voltage regulator triggered by a TPS6586x GPIO,
this allows to declare and initialize it conveniently from the "subdev" list.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add BTN_TOUCH event reporting to ucb1x00_ts touchscreen driver.
This will make this touchscreen driver behave consistently wrt.
BTN_TOUCH.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit or error. This is obsolete meanwhile, the core will do it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Provide platform data allowing the system to set the /IRQ pin into
CMOS mode rather than the default open drain. The default value of
this platform data reflects the default hardware configuration so
there should be no change to existing users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is a move to deprecate bus-specific PM operations and move to
using dev_pm_ops instead in order to reduce the amount of boilerplate
code in buses and facilitiate updates to the PM core. Do this move for
the pcf50633 driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No need to have them in the global namespace and sparse complains.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is a move to deprecate bus-specific PM operations and move to
using dev_pm_ops instead in order to reduce the amount of boilerplate
code in buses and facilitiate updates to the PM core. Do this move for
the adp5520 driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x touchscreen interrupts need acknowledgement even when using
direct signals to the CPU (which don't go through the core) so leave
the acknowledgement up to the touchscreen driver for simplicity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
builtin-top.c has an uninitialized variable.
gcc(version 4.5.1) warns about it and it results in build failure:
builtin-top.c: In function 'display_thread':
builtin-top.c:518:9: error: 'counter' may be used uninitialized
This situation can indeed trigger, if the getline() call in
prompt_integer() fails.
Signed-off-by: Akihiro Nagai <akihiro.nagai.hw@hitachi.com>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20110323072939.11638.50173.stgit@localhost6.localdomain6>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We always skipped flushing the BLT ring if the request flush did not
include the RENDER domain. However, this neglects that we try to flush
the COMMAND domain after every batch and before the breadcrumb interrupt
(to make sure the batch is indeed completed prior to the interrupt
firing and so insuring CPU coherency). As a result of the missing flush,
incoherency did indeed creep in, most notable when using lots of command
buffers and so potentially rewritting an active command buffer (i.e.
the GPU was still executing from it even though the following interrupt
had already fired and the request/buffer retired).
As all ring->flush routines now have the same preconditions, de-duplicate
and move those checks up into i915_gem_flush_ring().
Fixes gem_linear_blit.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35284
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: mengmeng.meng@intel.com
Along the fast path for relocation handling, we attempt to copy directly
from the user data structures whilst holding our mutex. This causes
lockdep to warn about circular lock dependencies if we need to pagefault
the user pages. [Since when handling a page fault on a mmapped bo, we
need to acquire the struct mutex whilst already holding the mm
semaphore, it is then verboten to acquire the mm semaphore when already
holding the struct mutex. The likelihood of the user passing in the
relocations contained in a GTT mmaped bo is low, but conceivable for
extreme pathology.] In order to force the mm to return EFAULT rather
than handle the pagefault, we therefore need to disable pagefaults
across the relocation fast path.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix up the debug file to report the right frequencies. On SNB, we program
the PCU with a frequency ratio, which is multiplied by 100MHz on the CPU
side. But GFX only runs at half that, so report it as such to avoid
confusion.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
The order of the calls does matter indeed. Swapping the call order of
intel_dp_destroy() and intel_dp_encoder_destroy() fixes the problem.
This is because i2c_del_adapter unregisters the device which parent is
intel_connector, and connectors are removed in intel_dp_destroy(). Thus
intel_dp_encoder_destroy() must be called before intel_dp_destroy().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=24822
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
We have a cmpxchg64_local() implementation but strange enough the
SMP capable variant cmpxchg64() is missing. So implement it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move xchg() and cmpxchg() functions to own header file like some
other architectures have done.
With this we make sure that system.h now really looks like a place
where everything is gathered that doesn't fit anywhere else.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the owner and name members of struct
ccwgroup_driver and convert all drivers to store
this data in the embedded struct device_driver.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make ccw_bus_type static. ccw_device drivers have to
use ccw_driver_register.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the owner and name members of struct
ccw_driver and convert all drivers to store
this data in the embedded struct device_driver.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Exit do_QDIO early if the buffer count is zero to prevent side effects
in the following functions.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make kernel bss section visible via /proc/iomem like on other
architectures.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Simplify setup_resources() and make it more generic. That way it is
easier to add additional resources.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Doesn't work and build for CONFIG_32BIT. So disable it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use snprintf() here as well so we won't have to deal with this again.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch fixed bugzilla #12965:
https://bugzilla.kernel.org/show_bug.cgi?id=12965
The original code contains some inproper use of sprintf
function where a buffer is used both as input string
as well as output string. It should remember the written
bytes in the previous and use that as the offset for
later writing. Also replace sprintf with snprintf.
Signed-off-by: Chen Liu <chenliu@asset.uwaterloo.ca>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
... even though it was disabled. A mistake in the handling of fence reuse
caused us to skip the vital delay of waiting for the object to finish
rendering before changing the register. This resulted in us changing the
fence register whilst the bo was active and so causing the blits to
complete using the wrong stride or even the wrong tiling. (Visually the
effect is that small blocks of the screen look like they have been
interlaced). The fix is to wait for the GPU to finish using the memory
region pointed to by the fence before changing it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34584
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Note for 2.6.38-stable, we need to reintroduce the interruptible passing]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Dave Airlie <airlied@linux.ie>
Similar to commit 7e59e097c0, this patch
avoids unnecessary volume control indices for more
Realtek auto-parsers, e g the ALC66x family, on the "Surround" and "Side"
controls.
These indices cause these volume controls to be ignored by PulseAudio and
vmaster and should be removed whenever possible.
Cc: stable@kernel.org
Reported-by: Jan Losinski <losinski@wh2.tu-dresden.de>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Removing think time checking. A high thinktime queue might means the queue
dispatches several requests and then do away. Limitting such queue seems
meaningless. And also this can simplify code. This is suggested by Vivek.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
For v2, I added back lines to cfq_preempt_queue() that were removed
during updates for accounting unaccounted_time. Thanks for pointing out
that I'd missed these, Vivek.
Previous commit "cfq-iosched: Don't set active queue in preempt" wrongly
cleared stats for preempting queues when it shouldn't have, because when
we choose a queue to preempt, it still isn't necessarily scheduled next.
Thanks to Vivek Goyal for figuring this out and understanding how the
preemption code works.
Signed-off-by: Justin TerAvest <teravest@google.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
A broken implementation of is_pot() prevented the detection of when a
singular pipe was enabled. Eric Anholt pointed out the existence of
is_power_of_2() so use that instead of our broken code!
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35402
Signed-off-by: Yuanhan Liu <yuanhan.liu@intel.com>
Tested-by: xunx.fang@intel.com
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
