...in e1000_update_nvm_checksum_ich8lan().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In MSI-X mode when an IMPI SoL session was active (i.e. the PHY reset was
blocked), the LSC interrupt generated by s/w to start the watchdog which
started the transmitter was not getting fired by the hardware because bit
24 (the 'other' cause bit) also needed to be set. Without an active SoL
session, the PHY was reset which caused the h/w to fire the LSC interrupt.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82574/82583 uses different registers/bits to setup manageability filters
than all other parts supported by e1000e; set them accordingly for IPMI
pass-through. Rename the function to better reflect what it does.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running ethtool online diagnostics with no open interface, there is a
short period of time where the driver relinquishes control of the adapter
during which time AMT (manageability firmware) can put the adapter into an
unknown state resulting in such things as link test failure, hardware hang,
reporting an incorrect link speed, etc. Resetting the adapter during an
open() resolves this by putting the adapter into a quiescent state.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple stack cleanups missed in an earlier patch from Jesse.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the access by tools for hardware queue engine and handle it
separately than other block registers, otherwise incorrect data
is returned.
Support for only NX3031 based cards.
Acked-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary remap of the region in bar 0 to access onhip memory
for NX3031.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NX3031 have 64bit on card memory. Fix the limit check to
64MB and remove unnecessary 128bit read/write check.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o For NX3031, MSI_MODE, CAPABILITIES_FW and SCRATCHPAD registers
are obsolete. These register addresses can be used for different
purpose.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert tipc_msg_* inline routines that are more than one line into
standard functions, thereby eliminating some repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert buf_acquire inline routine that is more than one line into
a standard function, thereby eliminating some repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert bearer congestion inline routine that is more than one line into
a standard function, thereby eliminating some repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts port list inline routines that are more than one line into
standard functions, thereby eliminating a significant amount of
repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts nmap inline routines that are more than one line into standard
functions, thereby eliminating a significant amount of repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert address-related inline routines that are more than one
line into standard functions, thereby eliminating a significant
amount of repeated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions have enough code in them such that they
seem like sensible targets for un-inlining. Prior to doing
that, this adds the tipc_ prefix to the functions, so that
in the event of a panic dump or similar, the subsystem from
which the functions come from is immediately clear.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than live in link.c where they can only be used in that file alone,
these helper routines are better served by being in link.h
Relocated are the following:
link_working_working
link_working_unknown
link_reset_unknown
link_reset_reset
link_blocked
link_congested
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a straight return of a field; there is no
value in the abstraction of hiding it behind a function.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate comments in TIPC's main API files that are either obsolete,
incorrect, misleading, or unhelpful. It also adds in one new comment.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide initial support for displaying overall TIPC status/statistics
information at runtime. Currently, only version info for the TIPC
kernel module is displayed.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make a cosmetic change to the name displayed for the broadcast link,
to better reflect its true nature. Since TIPC utilizes this link to
distribute name table information, in addition to multicast messages
sent by user applications, the prior name "multicast-link" is
no longer appropriate.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate a couple of instances where TIPC's native API send routines
were doing pointless initialization of local variables.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate some unused data structures in the TIPC
configuration service that relate to the handling of link
subscriptions, which were not supported when TIPC 1.5 was
introduced. If and when support for link subscriptions is
offered in TIPC, these elements may need to be re-introduced.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate an argument in a print statement that has no corresponding
format specification.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate a field of the TIPC port structure that is populated,
but never referenced.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usually "_text" is enough, but I received reports that its not always
available, so fallback to "_stext" for the symbol we use to check if we
need to apply any relocation to all the symbols in the kernel symtab,
for when, for instance, kexec is being used.
Reported-by: Darren Hart <dvhltc@us.ibm.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
An index of KVM44x_GUEST_TLB_SIZE is already one too large.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Hollis Blanchard <hollis@penguinppc.org>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
As the processor may not consider GUEST_INTR_STATE_STI as a reason for
blocking NMI, it could return immediately with EXIT_REASON_NMI_WINDOW
when we asked for it. But as we consider this state as NMI-blocking, we
can run into an endless loop.
Resolve this by allowing NMI injection if just GUEST_INTR_STATE_STI is
active (originally suggested by Gleb). Intel confirmed that this is
safe, the processor will never complain about NMI injection in this
state.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
KVM-Stable-Tag
Acked-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
cpuid_update may operate VMCS, so vcpu_load() and vcpu_put()
should be called to ensure correctness.
Signed-off-by: Dongxiao Xu <dongxiao.xu@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch makes KVM on 32 bit SVM working again by
correcting the masks used for iret interception. With the
wrong masks the upper 32 bits of the intercepts are masked
out which leaves vmrun unintercepted. This is not legal on
svm and the vmrun fails.
Bug was introduced by commits 95ba827313 and 3cfc3092.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvm_set_irq is used from non sleepable contexes, so convert ioapic from
mutex to spinlock.
KVM-Stable-Tag.
Tested-by: Ralf Bonenkamp <ralf.bonenkamp@swyx.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf_event: Fix oops due to perf_event_do_pending call
powerpc/swiotlb: Fix off by one in determining boundary of which ops to use
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] correct address of _stext with CONFIG_SHARED_KERNEL=y
[S390] ptrace: fix return value of do_syscall_trace_enter()
[S390] dasd: fix race between tasklet and dasd_sleep_on
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: preserve seq # on requeued messages after transient transport errors
ceph: fix cap removal races
ceph: zero unused message header, footer fields
ceph: fix locking for waking session requests after reconnect
ceph: resubmit requests on pg mapping change (not just primary change)
ceph: fix open file counting on snapped inodes when mds returns no caps
ceph: unregister osd request on failure
ceph: don't use writeback_control in writepages completion
ceph: unregister bdi before kill_anon_super releases device name
This patch adds the following.
1. Add new definitions of clock of type 'struct clksrc_clk'.
2. Add gate control function for GATE_SCLK1 which is required
for new clock additions.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clock source options avaialable in the clkset_mmc_spi are
applicable to clocks such as sclk_post, sclk_dispcon and
sclk_fimgvg. So this set is renamed as clkset_group1 to indicate
that it can be used as clock sources for other clocks and not
just for sclk_spi and sclk_mmc clocks.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add definitions of clocks of type 'struct clk'.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The pclk_low clock is of type 'struct clk' whereas on S5P6440,
the pclk_low clock is more suitable to be of type 'struct clksrc_clk'
(since pclk_low clock is a divided clock of hclk_low clock).
This patch modifies the following.
1. Removes the definition and usage of clk_p_clk clock.
2. Adds the clk_pclk_low clock of type 'struct clksrc_clk' clock.
3. Adds clk_pclk_low to the list of system clocks.
4. The clock rate of pclk_low is derived from the clk_pclk_low clock.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clk_h_low clock is of type 'struct clk' whereas on S5P6440,
the hclk_low clock is more suitable to be of type 'struct clksrc_clk'
(since hclk_low clock is derived from a choice of clock sources and
then divided by a divisor).
This patch modifies the following.
1. Removes the definition and usage of clk_h_clk clock.
2. Adds the clk_hclk_low clock of type 'struct clksrc_clk' clock.
3. Adds clk_hclk_low to the list of system clocks.
4. The clock rate of hclk_low is derived from the clk_hclk_low clock.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clk_p clock is of type 'struct clk' whereas on S5P6440,
the pclk is more suitable to be of type 'struct clksrc_clk'
(since pclk clock is divided version of hclk).
This patch modifies the following.
1. Adds the 'clk_pclk' clock which is of type 'struct clksrc_clk'.
2. Adds clk_pclk into the list of sysclks.
3. The clock rate 'pclk' is modified to be derived from clk_pclk.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clk_h clock is of type 'struct clk' whereas on S5P6440,
the hclk is more suitable to be of type 'struct clksrc_clk'
(since hclk clock is divided version of armclk)
This patch modifies the following.
1. Adds the 'clk_hclk' clock which is of type 'struct clksrc_clk'.
2. Removes all references to the clk_h clock.
3. Addes clk_hclk into the list of sysclks.
4. The clock rate 'hclk' is modified to be derived from clk_hclk.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This reverts commit 977d17bb17, because it
can cause problems with some devices not getting any resources at all
when the resource tree is re-allocated.
For an example of this, see
https://bugzilla.kernel.org/show_bug.cgi?id=15960
(originally https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4982)
(lkml thread: http://lkml.org/lkml/2010/4/19/20)
where Peter Henriksson reported his Xonar DX sound card gone, because
the IO port region was no longer allocated.
Reported-bisected-and-tested-by: Peter Henriksson <peter.henriksson@gmail.com>
Requested-by: Andrew Morton <akpm@linux-foundation.org>
Requested-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cachefiles_determine_cache_security() is expected to return with a
security override in place. However, if set_create_files_as() fails, we
fail to do this. In this case, we should just reinstate the security
override that was set by the caller.
Furthermore, if set_create_files_as() fails, we should dispose of the
new credentials we were in the process of creating.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If there are no active threasd using a semaphore, it is always correct
to unqueue blocked threads. This seems to be what was intended in the
undo code.
What was done instead, was to look for a sem count of zero - this is an
impossible situation, given that at least one thread is known to be
queued on the semaphore. The code might be correct as written, but it's
hard to reason about and it's not what was intended (otherwise the goto
out would have been unconditional).
Go for checking the active count - the alternative is not worth the
headache.
Signed-off-by: Michel Lespinasse <walken@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clk_arm clock is of type 'struct clk' whereas on S5P6440,
the arm clock is more suitable to be of type 'struct clksrc_clk'
(since arm clock is divided version of apll clock).
This patch modifies the following.
1. Removes the usage of clk_arm clock (defined in plat-s5p) and
defines the new clock 'clk_armclk' of type 'struct clksrc_clk'.
2. Rearranges the assignment of clock rate for the fout_a/m/epll
clocks. This will help in calculating the clock rate of fclk
from clk_armclk clock and setup the clock rate for fout_m/epll
for subsequent patches which depend on it.
3. Modifies the clock rate calculation of fclk to be based on
the newly added clk_armclk clock.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch modifies the following.
1. Modifies the dout_mpll clock type as clksrc_clk clock type.
This modification allows the use of common clock code in
managing the dout_mpll clock (which otherwise would need
custom defined functions such as s5p6440_clk_doutmpll_get_rate).
2. s5p6440_clk_doutmpll_get_rate function is removed as it is
no longer needed.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch modifies the following.
1. Registers the mout_apll clksrc_clk clock.
2. The mout_mpll and mout_epll were registered as 'struct clk'
types and then their parents were setup using the s3c_set_clksrc
function. This patch reduces the two steps into one by registering
the mout_mpll and mout_epll clocks using the s3c_register_clksrc
function.
3. As per point 2 above, the init_parents array is no longer required.
So the mout clocks are now put together in a new array named 'sysclks'.
The sysclks array will list the system level clocks and more
clocks will be added to it in the subsequent patches.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
