The ZTE modem entry causes usb-storage to ignore the device, but for some
versions of the device, usb-storage mode is required to get to modem ode. For
both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work.
Note that the various versions of the device have the same ProductId,
VendorId, and bcdDevice number, so we cannot have the entry for some and not
others.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds another unusual_devs.h entry for a device that can't handle more
than 64k reads/writes in a single command.
Signed-off-by: Jean-Baptiste Onofre <jb@nanthrax.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Running a 32-bit usbmon(8) on 2.6.28-rc9 produces the following:
ioctl32(usbmon:28563): Unknown cmd fd(3) cmd(400c9206){t:ffffff92;sz:12} arg(ffd3f458) on /dev/usbmon0
It happens because the compatibility mode was implemented for 2.6.18
and not updated for the fsops.compat_ioctl API.
This patch relocates the pieces from under #ifdef CONFIG_COMPAT into
compat_ioctl with no other changes except one new whitespace.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported by Randy Dunlap from a warning on the v2.6.29 merge window.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil.
Signed-off-by: Mhayk Whandson <eu@mhayk.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the vendor and product ID for the Alti-2 Neptune 3
(http://www.alti-2.com) which uses the FTDI chip.
Signed-off-by: Robie Basak <rb-oss-1@justgohome.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My girl use modem GSM (EDGE) Commanader 2 on iPlus Polsih provider,
PLEASE add this vendor=0x10C4 and product=0x822B to USB serial driver cp2101.c
From: Tomasz K <eros81@o2.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My Brother HL-1440 would print one document before CUPS would stop
printing with the error "Printer not connected; will retry in 30
seconds...". I traced this down to the CUPS usb backend getting an EIO
out of usblp on the IOCNR_GET_DEVICE_ID IOCTL. Adding the
USBLP_QUIRK_BIDIR fixes the problem but is it the right solution?
output from strace /usr/lib/cups/backend/usb after printing a document
(Note: SNDCTL_DSP_SYNC == IOCNR_GET_DEVICE_ID):
before patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fff2478cef0) = -1 EIO (Input/output error)
after patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fffb8d474c0) = 0
Possibly related bug: https://bugs.launchpad.net/ubuntu/+source/cupsys/+bug/35638
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Labpro device is in both ldusb and vstusb device tables.
Should only be a vstusb device.
Signed-off-by: stephen ware <stephen.ware@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a device quirk for a MediaTek Inc GPS chipset. The
device implements USB CDC ACM, but is missing the union descriptor, so
the ACM class driver fails to probe the device.
I've tested this patch with an iBlue A+ GPS which uses this chipset
and using kernel 2.6.28-rc9.
Signed-off-by: Andrew Lunn, <andrew@lunn.ch>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below is a patch which allows a number of GPS loggers to work
under linux. It is known to support the i-Blue 747 (all models),
i-Blue 757, Qstarz BT-Q1000, i.Trek Z1, Konet BGL-32, and the Holux
M-241.
From: James A. Treacy <treacy@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In some usb gadget driver, for example usb audio class device, the high
byte of w_index is the entity id and low byte is the interface number.
If we use the 2 bytes of w_index as the array number, we will get a
wrong pointer or NULL pointer.
This patch fixes this issue.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackfin MUSB Kconfig text didn't properly parenthesise its
dependencies. This was visible in non-Blackfin configs by the
way the user interfaces lost track of dependencies, when doing
a bunch of test builds.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initializes the actual_len field to 0 before every DMA transaction.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These compilation errors are related to incorrect
debugging macro and variable names and generated the
following errors:
drivers/usb/musb/cppi_dma.c:437:5: warning: "MUSB_DEBUG" is not defined
drivers/usb/musb/cppi_dma.c: In function 'cppi_next_rx_segment':
drivers/usb/musb/cppi_dma.c:884: error: 'debug' undeclared (first use in this function)
Signed-off-by: Hugo Villeneuve <hugo@hugovil.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/musb/tusb6010_omap.c:18:26: error: asm/arch/dma.h:
No such file or directory
drivers/usb/musb/tusb6010_omap.c:19:26: error: asm/arch/mux.h:
No such file or directory
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes insert module failure as free_irq() was not
done in previous rmmod.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DaVinci code had an implementation of the OTG transceiver glue
too; make it use the new-standard one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trying once more to get this merged. The original was submitted
for 2.6.27-rc2 or so, and never got correctly merged. Neither
were any of the numerous subsequent resends. Sigh.
CC drivers/usb/musb/davinci.o
drivers/usb/musb/davinci.c:35:32: error: mach/arch/hardware.h: No such file or directory
drivers/usb/musb/davinci.c:36:30: error: mach/arch/memory.h: No such file or directory
drivers/usb/musb/davinci.c:37:28: error: mach/arch/gpio.h: No such file or directory
drivers/usb/musb/davinci.c:373: error: redefinition of 'musb_platform_set_mode'
drivers/usb/musb/davinci.c:368: error: previous definition of 'musb_platform_set_mode' was here
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
> > drivers/built-in.o: In function `ohci_omap_init':
> > hid-quirks.c:(.text+0x6c608): undefined reference to `otg_get_transceiver'
> > drivers/built-in.o: In function `omap_udc_probe':
> > hid-quirks.c:(.init.text+0x34c0): undefined reference to `otg_get_transceiver'
> > hid-quirks.c:(.init.text+0x3d40): undefined reference to `otg_put_transceiver'
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1198) fixes a conceptual bug: Somewhere along the line
we managed to confuse USB class devices with USB char devices. As a
result, the code to send a disconnect signal to userspace would not be
built if both CONFIG_USB_DEVICE_CLASS and CONFIG_USB_DEVICEFS were
disabled.
The usb_fs_classdev_common_remove() routine has been renamed to
usbdev_remove() and it is now called whenever any USB device is
removed, not just when a class device is unregistered. The notifier
registration and unregistration calls are no longer conditionally
compiled. And since the common removal code will always be called as
part of the char device interface, there's no need to call it again as
part of the usbfs interface; thus the invocation of
usb_fs_classdev_common_remove() has been taken out of
usbfs_remove_device().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Alon Bar-Lev <alon.barlev@gmail.com>
Tested-by: Alon Bar-Lev <alon.barlev@gmail.com>
Cc: stable <stable@kernel.org>
Commit a0d4922da2
(USB: fix up suspend and resume for PCI host controllers) attempted
to fix the suspend-resume of PCI USB controllers, but unfortunately
it did that incorrectly and interrupts are left enabled by the USB
controllers' ->suspend_late() callback as a result. This leads to
serious problems during suspend which are very difficult to debug.
Fix the issue by removing the ->suspend_late() callback of PCI
USB controllers and moving the code from there to the ->suspend()
callback executed with interrupts enabled. Additionally, make
the ->resume() callback of PCI USB controllers execute
pci_enable_wake(dev, PCI_D0, false) to disable wake-up from the
full power state (PCI_D0).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Tested-by: "Jeff Chua" <jeff.chua.linux@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: "Zdenek Kabelac" <zdenek.kabelac@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1199) changes the initial wakeup settings for PCI USB
host controllers. The controllers are marked as capable of waking the
system, but wakeup is not enabled by default.
It turns out that enabling wakeup for USB host controllers has a lot
of bad consequences. As the simplest example, if a USB mouse or
keyboard is unplugged immediately after the computer is put to sleep,
the unplug will cause the system to wake back up again! We are better
off marking them as wakeup-capable and leaving wakeup disabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds an unusual devs entry for 2116:0320
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1200) finishes some fixes that were left incomplete by
an earlier patch.
Although nobody has addressed this issue in the past, it turns out
that we need to distinguish between two different modes of disabling
and enabling endpoints. In one mode only the data structures in
usbcore are affected, and in the other mode the host controller and
device hardware states are affected as well.
The earlier patch added an extra argument to the routines in the
enable_endpoint pathways to reflect this difference. This patch adds
corresponding arguments to the disable_endpoint pathways. Without
this change, the endpoint toggle state can get out of sync between
the host and the device. The exact mechanism depends on the details
of the host controller (whether or not it stores its own copy of the
toggle values).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dan Streetman <ddstreet@ieee.org>
Tested-by: Dan Streetman <ddstreet@ieee.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the vendor/product ID of the fasttrax GPS evaluation kit from:
http://www.fastraxgps.com/products/evaluationtools/evaluationkit/
to the cp2101 module since this device is actually equipped with a
CP210x USB to serial bridge.
The vendor/product ID is: 0x10c4/0x826b.
Signed-off-by: Wolfgang Glas <wolfgang.glas@ev-i.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-2.6.29' of git://linux-nfs.org/~bfields/linux:
nfsd: only set file_lock.fl_lmops in nfsd4_lockt if a stateowner is found
nfsd: fix cred leak on every rpc
nfsd: fix null dereference on error path
nfs: note that CONFIG_SUNRPC_XPRT_RDMA turns on server side support too
update port number in NFS/RDMA documentation
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] ibmvfc: Fix DMA mapping leak on memory allocation failure
[SCSI] qla2xxx: Update version number to 8.03.00-k2.
[SCSI] qla2xxx: Add checks for a valid fcport in dev-loss-tmo/terminate_rport_io callbacks.
[SCSI] qla2xxx: Correct regression in DMA-mask setting prior to allocations.
[SCSI] qla2xxx: Correct descriptions in flash manipulation routines.
[SCSI] qla2xxx: Correct regression in EH abort handling.
[SCSI] qla2xxx: Correct endianness issue during flash manipulation.
[SCSI] qla2xxx: Correct MSI-X vector allocation for single queue mode.
[SCSI] qla2xxx: Modify firmware-load order precedence for ISP81XX parts.
[SCSI] qla2xxx: Always serialize mailbox command execution.
[SCSI] qla2xxx: Ensure RISC-interrupt-enabled consistency for IS_NOPOLLING_TYPE() ISPs.
[SCSI] qla2xxx: Simplify sector-mask calculation in preparation for larger flash parts.
[SCSI] qla2xxx: Fix memory leak in error path
[SCSI] qla4xxx: do not reuse session when connecting to different target port
[SCSI] libiscsi: fix iscsi pool leak
Move the initialization of irq_default_affinity to early_irq_init as
core_initcall is too late.
irq_default_affinity can be used in init_IRQ and potentially timer and
SMP init as well. All of these happen before core_initcall. Moving
the initialization to early_irq_init ensures that it is initialized
before it is used.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Mike Travis <travis@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In interrupt.h these functions are declared only if
CONFIG_GENERIC_HARDIRQS is set. We should define them under identical
conditions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc 3.4.6 doesn't like MODULE_DEVICE_TABLE(dmi, x) expansion enough to
error out. Shut it up in a most simple way.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some hardware exposes PCIE slots in such a way that they can be claimed
by either the acpiphp or pciehp driver. pciehp is the preferred driver
if the firmware allows the OS to claim control via the _OSC method so
should be loaded first - if it fails to bind (either due to a missing
_OSC method or the firmware refusing to hand off control) then we can
fall back to acpiphp or a vendor-specific driver.
This patch simply changes the link order to ensure that pciehp will be
initialised before acpiphp if both are statically built into the kernel.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
nfsd4_lockt does a search for a lockstateowner when building the lock
struct to test. If one is found, it'll set fl_owner to it. Regardless of
whether that happens, it'll also set fl_lmops. Given that this lock is
basically a "lightweight" lock that's just used for checking conflicts,
setting fl_lmops is probably not appropriate for it.
This behavior exposed a bug in DLM's GETLK implementation where it
wasn't clearing out the fields in the file_lock before filling in
conflicting lock info. While we were able to fix this in DLM, it
still seems pointless and dangerous to set the fl_lmops this way
when we may have a NULL lockstateowner.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@pig.fieldses.org>
Since override_creds() took its own reference on new, we need to release
our own reference.
(Note the put_cred on the return value puts the *old* value of
current->creds, not the new passed-in value).
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Update the NFS/RDMA documentation to use the new port number assigned
by IANA.
Signed-off-by: James Lentini <jlentini@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
The SLAB kmalloc with a constant value isn't consistent with the other
implementations because it bails out with __you_cannot_kmalloc_that_much
rather than returning NULL and properly allowing the caller to fall back
to vmalloc or take other action. This doesn't happen with a non-constant
value or with SLOB or SLUB.
Starting with 2.6.28, I've been seeing build failures on s390x. This is
due to init_section_page_cgroup trying to allocate 2.5MB when the max size
for a kmalloc on s390x is 2MB.
It's failing because the value is constant. The workarounds at the call
size are ugly and the caller shouldn't have to change behavior depending
on what the backend of the API is.
So, this patch eliminates the link failure and returns NULL like the other
implementations.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: <stable@kernel.org> [2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
fixes kernel.org bugzilla 12538, xfs_fsr fails on 2.6.29-rc kernels
Regression caused by 743bb4650d
This was an embarrasing mistake, reallocating the sxp pointer passed
in from the main ioctl switch.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net
Reported-by: Paul Martin <pm@debian.org>
Tested-by: Paul Martin <pm@debian.org>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
For PCI devices, pci_bus_assign_resources() must be called to set up the
pci_device->resource array before pci_bus_add_devices() can be called, else
attempts to load drivers results in BAR collision errors where there are none.
This is not done in fakephp, so devices can be "unplugged" but scanning the
parent bus won't bring the devices back due to resource unallocation. Move the
pci_bus_add_device-calling logic into pci_rescan_bus and preface it with a call
to pci_bus_assign_resources so that we only have to (re)allocate resources once
per bus where a new device is found.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add an msi_mask() function which returns the correct bitmask for the
number of MSI interrupts you have. This fixes an undefined bug in
msi_capability_init().
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_restore_standard_config() adds extra delay for PCI buses in
low power states (B2 or B3), but this is only correct for buses in
B2, because the buses in B3 are reset when they are put back into
B0. Thus we should wait for such buses to settle after the reset,
but it's not a good idea to wait that long (1.1 s) with interrupts
off.
On the other hand, we have never waited for buses in B2 and B3
during resume and it seems reasonable to go back to this well
tested behaviour.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Devices that have MSI-X enabled before suspend to RAM or hibernation
and that are in a low power state during resume will not be handled
correctly by pci_restore_standard_config(). Namely, it first calls
pci_restore_state() which calls pci_restore_msi_state(), which in turn
executes __pci_restore_msix_state() that accesses the device's memory
space to restore the contents of the MSI-X table. However, if the
device is in a low power state at this point, it's memory space is
not accessible.
The easiest way to fix this potential problem is to make
pci_restore_standard_config() call pci_restore_state() after
it has put the device into the full power state, D0. Fortunately,
all of this is done with interrupts off, so the change of ordering
should not cause any trouble.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Hibernation breaks on EeePC 701 as a result of attempting to put one
of its (driverless) devices into a low power state. Avoid that by
not attepmting to power manage driverless devices during hibernation.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If one of device drivers refuses to suspend by returning error code
from its ->suspend() callback, the devices that have already been
suspended are resumed by executing their drivers' ->resume()
callbacks. Some of these callbacks expect the device's
configuration space to be restored if the device has been put into
D3 before they are called. Unfortunately, this mechanism has been
broken by recent changes moving the restoration of config spaces
of some devices (most importantly, USB controllers and HDA Intel)
into the resume callbacks executed with interrupts off. Obviously,
these callbacks are not invoked in the suspend error path and, as a
result, the system cannot be successfully brought back into the
working state in case of a suspend error. The same thing happens
in the hibernation error path right before putting the system into
S4.
Similarly, the suspend testing facility associated with the
/sys/power/pm_test file is broken, because it uses the very same
mechanism that is used in the suspend and hibernation error paths.
Fix the breakage by making the PCI core restore the configuration
spaces of PCI devices that haven't been restored already before
pci_pm_resume() is called for those devices by the PM core.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'hibern_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
SATA PIIX: Blacklist system that spins off disks during ACPI power off
SATA Sil: Blacklist system that spins off disks during ACPI power off
SATA AHCI: Blacklist system that spins off disks during ACPI power off
SATA: Blacklisting of systems that spin off disks during ACPI power off
DMI: Introduce dmi_first_match to make the interface more flexible
Hibernation: Introduce system_entering_hibernation
