During bootup, when we reprogram the PIT (programmable interval timer)
to start counting down from 0xffff in order to use it for the fast TSC
calibration, we should also make sure to delay a bit afterwards to allow
the PIT hardware to actually start counting with the new value.
That will happens at the next CLK pulse (1.193182 MHz), so the easiest
way to do that is to just wait at least one microsecond after
programming the new PIT counter value. We do that by just reading the
counter value back once - which will take about 2us on PC hardware.
Reported-and-tested-by: john stultz <johnstul@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit 14fa43f53f ("ASoC: Only
register AC97 bus if it's not done already") added a condition for
calling of soc_ac97_dev_register() but not added for calling of
soc_ac97_dev_unregister(). This patch adds same condition for
soc_ac97_dev_unregister(). Without this fix, kernel crashes when
unloading an asoc driver.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This follows the ARM change from Aaro Koskinen:
When unmapping N pages (e.g. shared memory) the amount of TLB
flushes done can be (N*PAGE_SIZE/ZAP_BLOCK_SIZE)*N although it
should be N at maximum. With PREEMPT kernel ZAP_BLOCK_SIZE is 8
pages, so there is a noticeable performance penalty when
unmapping a large VMA and the system is spending its time in
flush_tlb_range().
The problem is that tlb_end_vma() is always flushing the full VMA
range. The subrange that needs to be flushed can be calculated by
tlb_remove_tlb_entry(). This approach was suggested by Hugh
Dickins, and is also used by other arches.
The speed increase is roughly 3x for 8M mappings and for larger
mappings even more.
Bits and peices are taken from the ARM patch as well as the existing
arch/um implementation that is quite similar.
The end result is a significant reduction in both partial and full TLB
flushes initiated through flush_tlb_range().
At the same time, the nommu implementation was broken, had a superfluous
cache flush, and subsequently would have triggered a BUG_ON() if a
code-path had triggered it. Tidy this up for correctness and provide a
nopped-out implementation there.
More background on the initial discussion can be found at:
http://marc.info/?t=123609820900002&r=1&w=2http://marc.info/?t=123660375800003&r=1&w=2
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There were 3 invocations of task_hot() in can_migrate_task().
Replace these 3 invocations by only one invocation, cached in
a local variable.
Signed-off-by: Luis Henriques <henrix@sapo.pt>
LKML-Reference: <20090316195902.GA6197@hades.domain.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fixed typos in function documentation.
Signed-off-by: Luis Henriques <henrix@sapo.pt>
LKML-Reference: <20090316195809.GA6073@hades.domain.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While harmless, PTEA has different semantics on these parts, and is only
used in extended TLB mode. Kill off the legacy support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for extended ASIDs (up to 16-bits) on newer SH-X3 cores
that implement the PTAEX register and respective functionality. Presently
only the 65nm SH7786 (90nm only supports legacy 8-bit ASIDs).
The main change is in how the PTE is written out when loading the entry
in to the TLB, as well as in how the TLB entry is selectively flushed.
While SH-X2 extended mode splits out the memory-mapped U and I-TLB data
arrays for extra bits, extended ASID mode splits out the address arrays.
While we don't use the memory-mapped data array access, the address
array accesses are necessary for selective TLB flushes, so these are
implemented newly and replace the generic SH-4 implementation.
With this, TLB flushes in switch_mm() are almost non-existent on newer
parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the OOPS during a opl3sa2 card suspend
and resume if the driver is loaded but the card
is not found.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
IRQ for sh_eth of sh7763rdp became multi handling.
Therefore, the IRQ number of sh_eth is changed, too.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the ESPT-Giga (Ethernet Serial Parallel
Translator) SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is for Red Hat bug 490026: EXT4 panic, list corruption in
ext4_mb_new_inode_pa
ext4_lock_group(sb, group) is supposed to protect this list for
each group, and a common code flow to remove an album is like
this:
ext4_get_group_no_and_offset(sb, pa->pa_pstart, &grp, NULL);
ext4_lock_group(sb, grp);
list_del(&pa->pa_group_list);
ext4_unlock_group(sb, grp);
so it's critical that we get the right group number back for
this prealloc context, to lock the right group (the one
associated with this pa) and prevent concurrent list manipulation.
however, ext4_mb_put_pa() passes in (pa->pa_pstart - 1) with a
comment, "-1 is to protect from crossing allocation group".
This makes sense for the group_pa, where pa_pstart is advanced
by the length which has been used (in ext4_mb_release_context()),
and when the entire length has been used, pa_pstart has been
advanced to the first block of the next group.
However, for inode_pa, pa_pstart is never advanced; it's just
set once to the first block in the group and not moved after
that. So in this case, if we subtract one in ext4_mb_put_pa(),
we are actually locking the *previous* group, and opening the
race with the other threads which do not subtract off the extra
block.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
With arch/sh/drivers/dma/ always being built, the Dreamcast DMA engines
are being unconditionally built in, regardless of whether the DMA API is
enabled or not. This is a regression from previous behaviour, but there
is not much advantage in building them all in unconditionally regardless.
Add a new config option to make it optional, and update the only user of
it to reflect that.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It is trivial to merge the non-MMU and MMU versions of siginfo.h.
Without a single file "make headers_install" is broken for m68k
(since each of the sub-varients of siginfo.h are not installed).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The MMU version of unistd.h can be use on non-MMU platrorms as well.
Without a single file "make headers_install" is broken for m68k
(since each of the sub-varients of unistd.h are not installed).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
It is trivial to merge the non-MMU and MMU versions of signal.h.
Without a single file "make headers_install" is broken for m68k
(since each of the sub-varients of signal.h are not installed).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
It is trivial to merge the non-MMU and MMU versions of ptrace.h.
Without a single file "make headers_install" is broken for m68k
(since each of the sub-varients of ptrace.h are not installed).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The MMU version of setup.h can be used for all m68k platforms.
Without a single file "make headers_install" is broken for m68k
(since each of the sub-varients of setup.h are not installed).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
user needs to see this message even if debugging disabled
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hopefully the register contents will guide us to why this failure occured
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_clear_station_table will be called every time rxon called.
In this function ucode_key_table is set to 0 even though a static
WEP security is set. This will cause in many warning and might be
an issue if dynamic WEP is set. This patch make sure we keep track
of all existing static WEP when this function is called.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During preparation of TX we create DMA mapping to TX command as part of
preparing the TFD. This mapping needs to be cleared at the time TFD is
freed.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945 uses iwl_tx_cmd_complete to reclaim the unused buffers of the queue.
iwl_tx_cmd_complete in turn call the iwl_hcmd_queue_reclaim which will
unmap the dma mapping to tx_cmd and frees the memory.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes the bug 1900 at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1900
Issues:
Throughput and success ratio calculations were not done properly.
Number of retries were exceeding 16.
Fix:
Patch fixes above issues by doing window calculations inline with iwlwifi
Patch adds sanity check to limit number of retries to 16.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_led's structure from iwlwifi.
Patch also removes CONFIG_IWL3945_LEDS flag from Kconfig as 3945's led
support will now be enabled if user selects CONFIG_IWLWIFI_LEDS.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
error is:
iwl3945-base.c:545:5: warning: symbol 'iwl3945_set_dynamic_key' was not
declared. Should it be static?
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When iwlwifi driver receive fixed rate debugfs command, validate the
antenna selection, if the selection is invalid, report the valid antenna
choice and do not set the rate scale table to fixed rate. Otherwise, set
the entire rate scale table to the fixed rate request by the user. this
validation can prevent sysassert happen in uCode
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when perform rate scaling, in tx status function, checking for
IEEE80211_TX_STAT_AMPDU flag instead of IEEE_TX_CTL_AMPDU flag to perform
AMPDU rate scaling operation.
IEEE80211_TX_CTL_AMPDU was set by mac80211 for aggregation pkt. But when
iwlwifi receive the tx status reply, it reset the flag to following
info->flags = IEEE80211_TX_STAT_ACK;
info->flags |= IEEE80211_TX_STAT_AMPDU;
it causes the rate-scaling to not work for aggregation pkt if we checking
for IEEE80211_TX_CTL_AMPDU flag.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During rate scaling, checking for 0 retry count before decrement
the count by 1, this can avoid the retry count to become 255 (0xff),
which will cause the rate to drop faster than what we expect during good
condition (receive 0 retry packet). also change the algorithm to make
the rate not drop faster than what we like.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the MLME handshaking complete and tx aggregation started for the
tid. Do not send unnecessary turn on aggregation request to mac80211.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding more Radio information when displaying
rate_scale_table. This can help to understand how many antenna and the
current RF condition such as SISO, MIMO2, MIMO3.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when display rate_scale_table debugfs information, also display valid tx
antenna information, this will help user to select correct antenna when
issue fixed rate debugfs command
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before: 1099 errors, 93 warnings, 2854 lines checked
After: 19 errors, 47 warnings, 2976 lines checked
The big bulk of this is code indent and over 80 character lines
(Lindent did this part) Other changes are foo * bar spacing, and
trailing whitespace.
v2: Cleans up ill-indented comments. Subsequently, this reduces the
number of warnings, too. Thanks to Joe Perches for pointing this out!
v3: Ran the whole file through Lindent first... which does most of
the work for me. :) Again, thanks to Joe Perches for this.
This is my final answer!
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a driver for Marvell 88w8xxx TOPDOG PCI/PCIe wireless parts.
This initial version supports the 88w8687 802.11b/g PCIe part on
channels 1-11, and only STA mode is currently implemented.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must not disable ACK sending in this case since it would break
normal station operations. In addition, clarify the comment about AP
mode to make more sense.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the sparse complaints:
drivers/net/wireless/ath9k/eeprom.c:1407:5: warning: symbol
'ath9k_hw_4k_get_spur_channel' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:1436:19: warning: symbol
'eep_4k_ops' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2808:5: warning: symbol
'ath9k_hw_def_get_spur_channel' was not declared. Should it be static?
drivers/net/wireless/ath9k/eeprom.c:2837:19: warning: symbol
'eep_def_ops' was not declared. Should it be static?
CC [M] drivers/net/wireless/ath9k/eeprom.o
CHECK drivers/net/wireless/ath9k/mac.c
CC [M] drivers/net/wireless/ath9k/mac.o
CHECK drivers/net/wireless/ath9k/calib.c
drivers/net/wireless/ath9k/calib.c:883:6: warning: symbol 'ar9285_clc'
was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not a fatal message, hitting it simply means we're
going to tell the upper layers to slow their horses down but
as we make more descriptors available we let the show continue
by waking up the queues in ath_wake_mac80211_queue().
We downgrade this as otherwise we fill up your kernel log with
messages which can be common under heavy traffic.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a module parameter for mac80211_hwsim regulatory testing.
This module parameter is designed specifically to help test the
different possible types of driver specific regulatory requests
and also helps to test world roaming, all without any hardware.
If you want to just simply test different alpha2s just use the userspace
regulatory request as this won't buy you anything new.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to send to userspace "regulatory" events.
For now we just send an event when we change regulatory domains.
We also notify userspace when devices are using their own custom
world roaming regulatory domains.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this so we can later inform userspace who set the
regulatory domain and provide details of the request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used as we can always just assume the first
regulatory domain set will _always_ be a static regulatory
domain. REGDOM_SET_BY_CORE will be the first request from
cfg80211 for a regdomain and that then populates the first
regulatory request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even after commit "mac80211: deauth when interface is marked down"
(e327b847 on Linus tree), userspace still isn't notified when interface
goes down. There isn't a problem with this commit, but because of other
code changes it doesn't work on kernels >= 2.6.28 (works if same/similar
change applied on 2.6.27 for example).
The issue is as follows: after commit "mac80211: restructure disassoc/deauth
flows" in 2.6.28, the call to ieee80211_sta_deauthenticate added by
commit e327b847 will not work: because we do sta_info_flush(local, sdata)
inside ieee80211_stop (iface.c), all stations in interface are cleared, so
when calling ieee80211_sta_deauthenticate->ieee80211_set_disassoc (mlme.c),
inside ieee80211_set_disassoc we have this in the beginning:
sta = sta_info_get(local, ifsta->bssid);
if (!sta) {
The !sta check triggers, thus the function returns early and
ieee80211_sta_send_apinfo(sdata, ifsta) later isn't called, so
wpa_supplicant/userspace isn't notified with SIOCGIWAP.
This commit moves deauthentication to before flushing STA info
(sta_info_flush), thus the above can't happen and userspace is really
notified when interface goes down.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If cfg80211 requests a scan it awaits either a return code != 0 from
the scan function or the cfg80211_scan_done to be called. In case of
a STA mac80211's scan function ever returns 0 and queues the scan request.
If ieee80211_sta_work is executed and ieee80211_start_scan fails for
some reason cfg80211_scan_done will never be called but cfg80211 still
thinks the scan was triggered successfully and will refuse any future
scan requests due to drv->scan_req not being cleaned up.
If a scan is triggered from within the MLME a similar problem appears. If
ieee80211_start_scan returns an error, local->scan_req will not be reset
and mac80211 will refuse any future scan requests.
Hence, in both cases call ieee80211_scan_failed (which notifies cfg80211
and resets local->scan_req) if ieee80211_start_scan returns an error.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before: 881 errors, 265 warnings, 4507 lines checked
After: 114 errors, 273 warnings, 4548 lines checked
This was mostly "space required after that ',' (ctx:VxV)".
Also a fair number of whitespace, code indent, and C99 comment cleanups.
New warnings introduced are all "line over 80 character"
md5sums are identical, as I skipped any fixes which may have altered the resulting binary.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate table would not have been chosen before the interface
has been brought up. Reading 'rcstat' in this case would result
in an oops, fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
