This patch adds support for probing the MSAP bit within the Config3
register in order to detect the presence of the MSA ASE. Presence of the
ASE will be indicated in /proc/cpuinfo. The value of the MSA
implementation register will be displayed at boot to aid debugging and
verification of a correct setup, as is done for the FPU.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6430/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch introduces definitions for the MSA control registers and
functions which allow access to both the control & vector registers. If
the toolchain being used to build the kernel includes support for MSA
then this patch will make use of that support & use MSA instructions
directly. However toolchain support for MSA is very new & far from a
point where it can be reasonably expected that everyone building the
kernel uses a toolchain with support. Thus fallbacks using .word
assembler directives are also provided for now as a temporary measure.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6429/
Patchwork: https://patchwork.linux-mips.org/patch/6607/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When saving or restoring scalar FP context we want to access the least
significant 64 bits of each FP register. When the FP registers are 64
bits wide that is trivially the start of the registers value in memory.
However when the FP registers are wider this equivalence will no longer
be true for big endian systems. Define a new set of offset macros for
the least significant 64 bits of each saved FP register within thread
context, and make use of them when saving and restoring scalar FP
context.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6428/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When we want to access 64-bit FP register values we can only treat
consecutive registers as being consecutive in memory when the width of
an FP register equals 64 bits. This assumption will not remain true once
MSA support is introduced, so provide a code path which copies each 64
bit FP register value in turn when the width of an FP register differs
from 64 bits.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6427/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This code assumed that saved FP registers are 64 bits wide, an
assumption which will no longer be true once MSA is introduced. This
patch modifies the code to copy the lower 64 bits of each register in
turn, which is safe for any FP register width >= 64 bits.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6425/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The upper bits of an FP register are architecturally defined as
unpredictable following an instructions which only writes the lower
bits. The prior behaviour of the kernel is to leave them unmodified.
This patch modifies that to clear the upper bits to zero. This is what
the MSA architecture reference manual specifies should happen for its
wider registers and is still permissible for scalar FP instructions
given the bits unpredictability there.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: sergei.shtylyov@cogentembedded.com
Patchwork: https://patchwork.linux-mips.org/patch/6435/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
NUM_FPU_REGS just makes it clearer what's going on, rather than the
magic hard coded 32.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6424/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When a task which has used the FPU at some point in its past takes a
signal the kernel would previously always require the task to take
ownership of the FPU whilst setting up or restoring from the sigcontext.
That means that if the task has not used the FPU within this timeslice
then the kernel would enable the FPU, restore the task's FP context into
FPU registers and then save them into the sigcontext. This seems
inefficient, and if the signal handler doesn't use FP then enabling the
FPU & the extra memory accesses are entirely wasted work.
This patch modifies the sigcontext setup & restore code to copy directly
between the tasks saved FP context & the sigcontext for any tasks which
have used FP in the past but are not currently the FPU owner (ie. have
not used FP in this timeslice).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6423/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These functions aren't directly related to the FPU emulator at all, they
simply copy between a thread's saved context & a sigcontext. Thus move
them to the appropriate signal files & rename them accordingly. This
makes it clearer that the functions don't require the FPU emulator in
any way.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6422/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The hard-coded offsets mentioned in this comment seem to not exist
anymore, so remove mention of them from the comment.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6421/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch replaces the fpureg_t typedef with a "union fpureg" enabling
easier access to 32 & 64 bit values. This allows the access macros used
in cp1emu.c to be simplified somewhat. It will also make it easier to
expand the width of the FP registers as will be done in a future
patch in order to support the 128 bit registers introduced with MSA.
No behavioural change is intended by this patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6532/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When userland uses syscall() to perform an indirect system call
the actually system call that needs to be checked by the filter
is on the first argument. The kernel code needs to handle this case
by looking at the original syscall number in v0 and if it's
NR_syscall, then it needs to examine the first argument to
identify the real system call that will be executed.
Similarly, we need to 'virtually' shift the syscall() arguments
so the syscall_get_arguments() function can fetch the correct
arguments for the indirect system call.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6404/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS now has the infrastructure for dynamic seccomp-bpf
filtering
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6400/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add _TIF_SECCOMP flag to _TIF_WORK_SYSCALL_ENTRY to indicate
that the system call needs to be checked against a seccomp filter.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6405/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This effectively renames __syscall_get_arch to syscall_get_arch
and implements a compatible interface for the seccomp API.
The seccomp code (kernel/seccomp.c) expects a syscall_get_arch
function to be defined for every architecture, so we drop
the leading underscores from the existing function.
This also makes use of the 'task' argument to determine the type
the process instead of assuming the process has the same
characteristics as the kernel it's running on.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6398/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The syscall_rollback function is used by seccomp-bpf but it was never
added for MIPS. It doesn't need to do anything as none of the registers
are clobbered if the system call has been denied by the seccomp filter.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6403/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CONFIG_MIPS_CPS is a better option for systems where it is supported,
which as far as I am aware should be all systems where CONFIG_MIPS_CMP
could provide any value (ie. where there are multiple cores for YAMON to
bring up). This option is therefore deprecated, and marked as such. It
is left intact for the time being in order to provide a fallback should
someone find a system where CONFIG_MIPS_CPS will not function (ie. where
the reset vector cannot be moved), and should be removed entirely in the
future assuming that does not happen.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6369/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit f55afb0969cc "MIPS: Clean up MIPS MT and CMP configuration
options." introduced a dependency upon MIPS_MT_SMP (ie. SMVP) for the
MIPS_CMP (ie. CMP framework support) Kconfig option. It did not specify
why, and that dependency is bogus. It is perfectly valid to have a
multi-core system with the YAMON bootloader but without MT support -
an example of this would be any multi-core proAptiv bitstream running on
a Malta. Forcing MT support to be enabled in a kernel for such a system
is incorrect. I suspect that the dependency was actually meant to
reflect the fact that YAMON will only bind 1 TC per VPE on an MT system,
and only describe those 1:1 TC:VPE pairs as CPUs through the AMON
interface. Thus an SMTC kernel makes little sense on a system using
MIPS_CMP, and the Kconfig dependencies should reflect that rather than
introducing the bogus SMVP dependency.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6368/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The prior help text introduced in commit f55afb0969cc "MIPS: Clean up
MIPS MT and CMP configuration options." reads as though this option
enables the kernel to make use of the CM hardware, which is not true.
What it actually does is allow the kernel to interact with the YAMON
bootloader which actually interacts with the CM hardware to bring up
secondary cores. Re-introduce the word "framework" which that commit
removed to avoid misleading people.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6367/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This header was used only by Malta but is used no longer. Remove it. It
was also included unnecessarily in irq-gic.c, so that include is also
removed.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6366/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch simply attempts to register the MIPS Coherent Processing
System SMP implementation when it is enabled. If registering that fails
for some reason (like the Kconfig option being disabled or a lack of
hardware support) then we fall back to the same SMP implementations as
before.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6365/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When CPC support is compiled into the kernel (ie. CONFIG_MIPS_CPC=y),
probe the CPC on boot for Malta in order to allow any users of the CPC
to detect its presence & function correctly.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the Malta-specific CM probe code and instead make use of the
newly added generic CM code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6364/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now, devices will have 32-bit default DMA masks (0xFFFFFFFF) as per DMA API.
Fixes:
$ ifconfig eth0 up
net eth0: coherent DMA mask is unset
$ ifconfig hdlc0 up
net hdlc0: coherent DMA mask is unset
Also fixes a cosmetic off-by-one bug which caused DMA transfers ending exactly
on the 64 MiB boundary to go through dmabounce unnecessarily.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Tested-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This reverts commit bfdad565ae.
The patch turned out to be incorrect, and will be replaced
with a correct patch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 098e30f655 "ARM: ixp4xx: stop broadcasting the custom GPIO API"
changed the internal gpio code of ixp4xx to be accessible only from
common.c, but unfortunately that broke the Goramo MultiLink code, which
uses this API.
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'set_scl':
arch/arm/mach-ixp4xx/goramo_mlr.c:82: error: implicit declaration of function 'gpio_line_set'
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'output_control':
arch/arm/mach-ixp4xx/goramo_mlr.c:111: error: implicit declaration of function 'gpio_line_config'
arch/arm/mach-ixp4xx/goramo_mlr.c:111: error: 'IXP4XX_GPIO_OUT' undeclared
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'hss_dcd_irq':
arch/arm/mach-ixp4xx/goramo_mlr.c:155: error: implicit declaration of function 'gpio_line_get'
arch/arm/mach-ixp4xx/goramo_mlr.c: In function 'gmlr_init':
arch/arm/mach-ixp4xx/goramo_mlr.c:416: error: 'IXP4XX_GPIO_OUT' undeclared
arch/arm/mach-ixp4xx/goramo_mlr.c:421: error: 'IXP4XX_GPIO_IN' undeclared
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The vpe_id field of struct cpuinfo_mips is only present when one of
CONFIG_MIPS_MT_{SMP,SMTC} is enabled. That means that any code accessing
which may compile without MT is currently forced to use an #ifdef.
Instead this patch provides an accessor macro, #ifdef'd appropriately
to prevent further #ifdef's elsewhere.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6646/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some applications didn't expect recvmsg() on a non blocking socket
could return -EINTR. This possibility was added as a side effect
of commit b3ca9b02b0 ("net: fix multithreaded signal handling in
unix recv routines").
To hit this bug, you need to be a bit unlucky, as the u->readlock
mutex is usually held for very small periods.
Fixes: b3ca9b02b0 ("net: fix multithreaded signal handling in unix recv routines")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Petazzoni says:
====================
net: mvneta: fix usage as a module
The following set of two patches fix the usage of the mvneta driver
when built as a module, and used in RGMII configurations. It is
somewhat similar to a previous fix that was made by Arnaud Patard, but
which was limited to SGMII configurations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver currently uses of_iomap(), which has two drawbacks:
it doesn't request the resource, and it isn't devm-style so some error
handling is needed.
This commit switches to use devm_ioremap_resource() instead, which
automatically requests the resource (so the I/O registers region shows
up properly in /proc/iomem), and also is devm-style, which allows to
get rid of some error handling to unmap the I/O registers region.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5445eaf309 ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.
However, it turns out that the Armada XP GP, which uses RGMII, is
affected by a similar problem: its SERDES configuration is lost when
mvneta is loaded as a module, because this configuration is set by the
bootloader, and then lost because the clock is gated by the clock
framework until the mvneta driver is loaded again and the clock is
re-enabled.
However, it turns out that for the RGMII case, setting the SERDES
configuration is not sufficient: the PCS enable bit in the
MVNETA_GMAC_CTRL_2 register must also be set, like in the SGMII
configuration.
Therefore, this commit reworks the SGMII/RGMII initialization: the
only difference between the two now is a different SERDES
configuration, all the rest is identical.
In detail, to achieve this, the commit:
* Renames MVNETA_SGMII_SERDES_CFG to MVNETA_SERDES_CFG because it is
not specific to SGMII, but also used on RGMII configurations.
* Adds a MVNETA_RGMII_SERDES_PROTO definition, that must be used as
the MVNETA_SERDES_CFG value in RGMII configurations.
* Removes the mvneta_gmac_rgmii_set() and mvneta_port_sgmii_config()
functions, and instead directly do the SGMII/RGMII configuration in
mvneta_port_up(), from where those functions where called. It is
worth mentioning that mvneta_gmac_rgmii_set() had an 'enable'
parameter that was always passed as '1', so it was pretty useless.
* Reworks the mvneta_port_up() function to set the MVNETA_SERDES_CFG
register to the appropriate value depending on the RGMII vs. SGMII
configuration. It also unconditionally set the PCS_ENABLE bit (was
already done for SGMII, but is now also needed for RGMII), and sets
the PORT_RGMII bit (which was already done for both SGMII and
RGMII).
This commit was successfully tested with mvneta compiled as a module,
on both the OpenBlocks AX3 (SGMII configuration) and the Armada XP GP
(RGMII configuration).
Reported-by: Steve McIntyre <steve@einval.com>
Cc: stable@vger.kernel.org # 3.11.x: 5445eaf309 mvneta: Try to fix mvneta when compiled as module
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit 3 of the MVNETA_GMAC_CTRL_2 is actually used to enable the PCS,
not the PSC: there was a typo in the name of the define, which this
commit fixes.
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ethtool related functions.
Signed-off-by: Vipul Pandya <vipul.pandya@samsung.com>
Neatening-by: Joe Perches <joe@perches.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds TX and RX checksum offload support.
Signed-off-by: Vipul Pandya <vipul.pandya@samsung.com>
Neatening-by: Joe Perches <joe@perches.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable TSO during initialization for each DMA channels
Signed-off-by: Vipul Pandya <vipul.pandya@samsung.com>
Neatening-by: Joe Perches <joe@perches.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for the EEE(Energy Efficient Ethernet) in 10G ethernet driver.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Neatening-by: Joe Perches <joe@perches.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Samsung 10Gb ethernet driver(sxgbe).
- sxgbe core initialization
- Tx and Rx support
- MDIO support
- ISRs for Tx and Rx
- ifconfig support to driver
Signed-off-by: Siva Reddy Kallam <siva.kallam@samsung.com>
Signed-off-by: Vipul Pandya <vipul.pandya@samsung.com>
Signed-off-by: Girish K S <ks.giri@samsung.com>
Neatening-by: Joe Perches <joe@perches.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds binding document for SXGBE ethernet driver via device-tree.
Signed-off-by: Siva Reddy Kallam <siva.kallam@samsung.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Dong Zhu <bluezhudong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ding Tianhong says:
====================
bonding: support QinQ for bond arp interval
v1->v2: remvoe the comment "TODO: QinQ?".
convert pr_xxx() to pr_xxx_ratelimited() for arp interval.
v2->v3: remove the unnecessary log for arp interval and add net ratelimit to
avoid spam log.
v3->v4: Add ratelimit for debugging is not a good idea, it will miss some message
if the user turns the debugging on, so don't add ratelimited on debugging.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the unnecessary log and add net_ratelimit to the others, in order to
avoid spam the log.
Cc: Joe Perches <joe@perches.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond send arp request to indicate that the slave is active, and if the bond dev
is a vlan dev, it will set the vlan tag in skb to notice the vlan group, but the
bond could only send a skb with 802.1q proto, not support for QinQ.
So add outer tag for lower vlan tag and inner tag for upper vlan tag to support QinQ,
The new skb will be consist of two vlan tag just like this:
dst mac | src mac | outer vlan tag | inner vlan tag | data | .....
If We don't need QinQ, the inner vlan tag could be set to 0 and use outer vlan tag
as a normal vlan group.
Using "ip link" to configure the bond for QinQ and add test log:
ip link add link bond0 bond0.20 type vlan proto 802.1ad id 20
ip link add link bond0.20 bond0.20.200 type vlan proto 802.1q id 200
ifconfig bond0.20 11.11.20.36/24
ifconfig bond0.20.200 11.11.200.36/24
echo +11.11.200.37 > /sys/class/net/bond0/bonding/arp_ip_target
90:e2:ba:07:4a:5c (oui Unknown) > Broadcast, ethertype 802.1Q-QinQ (0x88a8),length 50: vlan 20, p 0,ethertype 802.1Q, vlan 200, p 0, ethertype ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 11.11.200.37 tell 11.11.200.36, length 28
90:e2:ba:06:f9:86 (oui Unknown) > 90:e2:ba:07:4a:5c (oui Unknown), ethertype 802.1Q-QinQ (0x88a8), length 50: vlan 20, p 0, ethertype 802.1Q, vlan 200, p 0, ethertype ARP, Ethernet (len 6), IPv4 (len 4), Reply 11.11.200.37 is-at 90:e2:ba:06:f9:86 (oui Unknown), length 28
v1->v2: remove the comment "TODO: QinQ?".
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan support 2 proto: 802.1q and 802.1ad, so make a new function
called vlan_dev_vlan_proto() which could return the vlan proto for
input dev.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ding Tianhong says:
====================
bonding: slight optimization and avoid spam for bond xmit path
v1->v2: Add ratelimit for debugging is not a good idea, it will miss some message
if the user turns the debugging on, so remove the patch 3.
use net_err_ratelimited instead of pr_err_ratelimited and use __func__ instead of
bond_xmit_broadcast().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
