This does a bit of refactoring of the FPGA management code. The primary
FPGA initialization is moved out to its own file in preparation for
implementing some of the more complex capabilities, a complete set of
register definitions is provided, and all of the existing users in the
board code are moved over to use the new interface instead of setting up
overlapping mappings. This also corrects the FPGA size, which previously
was chomped off at the SDIF control register.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
no functional change -- cleanup only.
acpi_processor_power_verify_c2() was nearly empty due to a previous patch,
so expand its remains into its one caller and delete it.
Signed-off-by: Len Brown <len.brown@intel.com>
Do for C3 what the previous patch did for C2.
The C2 patch was in response to a highly visible
and multiply reported C-state/turbo failure,
while this change has no bug report in-hand.
This will enable C3 in Linux on systems where BIOS
overstates C3 latency in _CST. It will also enable
future systems which may actually have C3 > 1000usec.
Linux has always ignored ACPI BIOS C3 with exit latency > 1000 usec,
and the ACPI spec is clear that is correct FADT-supplied C3.
However, the ACPI spec explicitly states that _CST-supplied C-states
have no latency limits.
So move the 1000usec C3 test out of the code shared
by FADT and _CST code-paths, and into the FADT-specific path.
Signed-off-by: Len Brown <len.brown@intel.com>
Linux has always ignored ACPI BIOS C2 with exit latency > 100 usec,
and the ACPI spec is clear that is correct FADT-supplied C2.
However, the ACPI spec explicitly states that _CST-supplied C-states
have no latency limits.
So move the 100usec C2 test out of the code shared
by FADT and _CST code-paths, and into the FADT-specific path.
This bug has not been visible until Nehalem, which advertises
a CPU-C2 worst case exit latency on servers of 205usec.
That (incorrect) figure is being used by BIOS writers
on mobile Nehalem systems for the AC configuration.
Thus, Linux ignores C2 leaving just C1, which is
saves less power, and also impacts performance
by preventing the use of turbo mode.
http://bugzilla.kernel.org/show_bug.cgi?id=15064
Tested-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
resource->domain_devices can be double kfree()'d in a couple of places.
Fix this by setting num_domain_devices = 0 after the kfree().
Coverity CID: 13356, 13355, 13354
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 78f1699 (ACPI: processor: call _PDC early) blindly walks
the namespace and calls _PDC on every processor object it finds.
This change may cause issues on platforms that declare dummy
values for SSDTs on non-present processors (disabled in MADT).
When we call _PDC and dynamically attempt to execute the AML
Load() op on these dummy SSDTs, there's no telling what might
happen.
Rather than finding every platform that has bogus SSDTs, restrict
early _PDC calls to platforms that are known to need early
evaluation of _PDC.
This is a minimal, temporary fix (given the context of the
current release cycle). A real solution of checking the MADT for
non-present processors will be written for the next merge window.
References:
http://bugzilla.kernel.org/show_bug.cgi?id=14710http://bugzilla.kernel.org/show_bug.cgi?id=14954
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The "full_alg_name" variable is used on a couple error paths, so we
shouldn't free it until the end.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
The variable lower_dentry is initialized twice to the same (side effect-free)
expression. Drop one initialization.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@forall@
idexpression *x;
identifier f!=ERR_PTR;
@@
x = f(...)
... when != x
(
x = f(...,<+...x...+>,...)
|
* x = f(...)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
ecryptfs_interpose checks if one of the flags passed is
ECRYPTFS_INTERPOSE_FLAG_D_ADD, defined as 0x00000001 in ecryptfs_kernel.h.
But the only user of ecryptfs_interpose to pass a non-zero flag to it, has
hard-coded the value as "1". This could spell trouble if any of these values
changes in the future.
Signed-off-by: Erez Zadok <ezk@cs.sunysb.edu>
Cc: Dustin Kirkland <kirkland@canonical.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Unnecessary because it would unhash perfectly valid dentries, causing them
to have to be re-looked up the next time they're needed, which presumably is
right after.
Signed-off-by: Aseem Rastogi <arastogi@cs.sunysb.edu>
Signed-off-by: Shrikar archak <shrikar84@gmail.com>
Signed-off-by: Erez Zadok <ezk@cs.sunysb.edu>
Cc: Saumitra Bhanage <sbhanage@cs.sunysb.edu>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Ecryptfs_open dereferences a pointer to the private lower file (the one
stored in the ecryptfs inode), without checking if the pointer is NULL.
Right afterward, it initializes that pointer if it is NULL. Swap order of
statements to first initialize. Bug discovered by Duckjin Kang.
Signed-off-by: Duckjin Kang <fromdj2k@gmail.com>
Signed-off-by: Erez Zadok <ezk@cs.sunysb.edu>
Cc: Dustin Kirkland <kirkland@canonical.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Adrian reported that mkfontscale didn't work inside of eCryptfs mounts.
Strace revealed the following:
open("./", O_RDONLY|O_NONBLOCK|O_LARGEFILE|O_DIRECTORY|O_CLOEXEC) = 3
fcntl64(3, F_GETFD) = 0x1 (flags FD_CLOEXEC)
open("./fonts.scale", O_WRONLY|O_CREAT|O_TRUNC, 0666) = 4
getdents(3, /* 80 entries */, 32768) = 2304
open("./.", O_RDONLY) = 5
fcntl64(5, F_SETFD, FD_CLOEXEC) = 0
fstat64(5, {st_mode=S_IFDIR|0755, st_size=16384, ...}) = 0
mmap2(NULL, 16384, PROT_READ, MAP_PRIVATE, 5, 0) = 0xb7fcf000
close(5) = 0
--- SIGBUS (Bus error) @ 0 (0) ---
+++ killed by SIGBUS +++
The mmap2() on a directory was successful, resulting in a SIGBUS
signal later. This patch removes mmap() from the list of possible
ecryptfs_dir_fops so that mmap() isn't possible on eCryptfs directory
files.
https://bugs.launchpad.net/ecryptfs/+bug/400443
Reported-by: Adrian C. <anrxc@sysphere.org>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
The i_blocks field of an eCryptfs inode cannot be trusted, but
generic_fillattr() uses it to instantiate the blocks field of a stat()
syscall when a filesystem doesn't implement its own getattr(). Users
have noticed that the output of du is incorrect on newly created files.
This patch creates ecryptfs_getattr() which calls into the lower
filesystem's getattr() so that eCryptfs can use its kstat.blocks value
after calling generic_fillattr(). It is important to note that the
block count includes the eCryptfs metadata stored in the beginning of
the lower file plus any padding used to fill an extent before
encryption.
https://bugs.launchpad.net/ecryptfs/+bug/390833
Reported-by: Dominic Sacré <dominic.sacre@gmx.de>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
When truncating inodes in the lower filesystem, eCryptfs directly
invoked vmtruncate(). As Christoph Hellwig pointed out, vmtruncate() is
a filesystem helper function, but filesystems may need to do more than
just a call to vmtruncate().
This patch moves the lower inode truncation out of ecryptfs_truncate()
and renames the function to truncate_upper(). truncate_upper() updates
an iattr for the lower inode to indicate if the lower inode needs to be
truncated upon return. ecryptfs_setattr() then calls notify_change(),
using the updated iattr for the lower inode, to complete the truncation.
For eCryptfs functions needing to truncate, ecryptfs_truncate() is
reintroduced as a simple way to truncate the upper inode to a specified
size and then truncate the lower inode accordingly.
https://bugs.launchpad.net/bugs/451368
Reported-by: Christoph Hellwig <hch@lst.de>
Acked-by: Dustin Kirkland <kirkland@canonical.com>
Cc: ecryptfs-devel@lists.launchpad.net
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
We need to set the omap_chip.oc carefully for the clocks to work.
To fix this, set the omap_chip.oc in omap3_check_features() based
on the CONTROL_IDCODE and silicon revision registers.
Also add handling for 34xx es3.1.2 as es3.1 for now.
Fixes booting on at least overo board.
Based on an earlier patch by Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make the omap_mux_read and write available for board code,
and rename omap_mux_set_board_signals into omap_mux_write_array.
Also add the related prototypes and comments into mux.h.
In some cases we want to change the signals dynamically,
mostly for power management.
Note that we cannot use the signal names as they are set
__init to save memory.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like cmdline muxing got broken at some point when we
decided to limit muxing to __init code. Currently omap_mux_entry
list is not yet initialized when we try to initialize cmdline
muxing.
Fix this by calling omap_mux_init_list() before calling
omap_mux_set_cmdline_signals().
Reported-by: Philip Balister <philip@balister.org>
Tested-by: Philip Balister <philip@balister.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
gcc warns of an array subscript out of bounds in xfs_mod_sb().
The code is written in such a way that if the array subscript is
out of bounds, then it will assert fail. Rearrange the code to
avoid the bounds check warning.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The first thing that omap2_init_clksel_parent() does is check for
a non-zero .clksel field in the struct clk. Therefore, it is
pointless calling this function on clocks where the clksel field
is unset.
Remove init calls to omap2_init_clksel_parent() on clocks without
a clksel field.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In the current implementation the sysconfig value is read into
_sysc_cache once and an actual update to the sysconfig register
happens only if the new value paased is differnt from the one in _sysc_cache.
_sysc_cache is updated only if _HWMOD_SYSCONFIG_LOADED is not set.
This can lead to the follwing issue if off mode is enabled in modules
which employs "always-retore" mechanism of context save and restore.
a. The module sets the sysconfig register through omap_device_enable.
Here _sysc_cache is updated with the value written to the sysconfig
register and left.
b. The power domain containig the module enters off mode and the
module context is lost.
c. The module in use becomes active and calls omap_device_enable to
enable itself. Here a read of sysconfig register does not happen
as _HWMOD_SYSCONFIG_LOADED flag is set. The value to be written
to the sysconfig register will be same as the one written in step a.
Since _sysc_cache reflects the previous written value an update
of the sysconfig register does not happen.
This means in modules which employs "always-restore" mechanism
after off , the sysconfig regsiters will never get updated.
This patch introduces a flag SYSC_NO_CACHE which if set ensures that the
sysconfig register is always read into _sysc_cache before an update is
attempted.
This flags need to be set only by modules which does not do a context save
but re-initializes the registers every time the module is accessed. This
includes modules like i2c, smartreflex etc.
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: tweaked to apply on a different head, added flag comment]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Initialise the xfs_bmalloca_t structure to zero to avoid uninitialised
variable warnings. This is done by zeroing the arg structure rather than
using the uninitialised_var() trick so we know for certain that the
structure is correctly initialised as xfs_bmapi is a very complex
function and it is difficult to prove warnings are spurious.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The -fno-unsigned-char directive has no effect anymore as the
XFs build is clean. However, the kernel build hides pointer sign
differences so turn that back on so that we can clean up all the
mismatches prior to a userspace code resync.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
We are now consistently using unsigned char strings for names
so fix up the remaining warnings in the dir2 code to complete
the cleanup.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
To be consistent with the directory code, the attr code should use
unsigned names. Convert the names from the vfs at the highest level
to unsigned, and ænsure they are consistenly used as unsigned down
to disk.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
xfs_buf_iomove() uses xfs_caddr_t as it's parameter types, but it doesn't
care about the signedness of the variables as it is just copying the
data. Change the prototype to use void * so that we don't get sign
warnings at call sites.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
To be consistent across the codebase, convert the dirnameops to pass
the directory names by unsigned char strings.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
dmops uses a signed char for it's namespace event. To be consistent
with the rest of the code, convert them to unsigned char for the
namespace string.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Convert the struct xfs_name to use unsigned chars for the name
strings to match both what is stored on disk (__uint8_t) and what
the VFS expects (unsigned char).
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The comments in cacheflush.h should follow what's in
struct cpu_cache_fns. The comments for V6 and V7 are
unnecessary.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When cleaning up beacon buffers and slots, ath9k currently checks if
sc->ah->opmode is set to a beacon related mode before cleaning up
buffers.
An unfortunate ordering of interface up/down commands can lead to
sc->ah->opmode being set to monitor mode, while there are AP interfaces
present on the same wiphy.
Always cleaning up beacon buffers if present fixes this issue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix check to verify if a register bit is set. We have not hit this bug because
wait_for_cmd_complete() is always called with S2IO_BIT_RESET.
Reported by Roel Kluin <roel.kluin@gmail.com>.
Signed-off-by: Ram Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments in arm_machine_restart() suggest that cpu_proc_fin()
will clean and disable cache and turn off interrupts. This does
not seem to be implemented for proc-v7.S, implement it the same
way as for proc-v6.S.
This also makes kexec work for v7. Note that a related TLB and
branch traget flush patch is also needed to avoid kexec
"crc error".
Note that there are still some issues that seem to be related
to L2 cache being on and causing occasional uncompress "crc error"
with kexec. Anyways, this gets kexec mostly working on V7 for now.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to do that if we tinker with the MMU entries.
This fixes the occasional bug with kexec where the new
fails to uncompress with "crc error". Most likely at
least kexec on v6 and v7 need this fix.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Without this patch arch/arm/compressed/head.S defaults to generic
DCC code that does not work for v7.
For more information on the v7 DCC, see Cortex-A8 TRM
"12.11.1 Debug communications channel".
To use it with post 2.6.33-rc1 or later, you need to have:
CONFIG_DEBUG_LL=y
ONFIG_DEBUG_ICEDCC=y
CONFIG_EARLY_PRINTK=y
Earlier kernels need commit 93fd03a8c6
backported.
Tested on omap3430.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Usually we can look to the CVR to work out whether we have an FPU or not.
Unfortunately not all parts comply with this, so just set the flag
manually for all SH-4 parts and clear it on the only SH-4 that doesn't
have one (SH4-501).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In a string like "v:SIP/2.0..." it was checking for !isalpha('S') when it
meant to be inspecting the ':'.
Patch by Greg Alexander <greqcs@galexander.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch updates the PFC code with some clarifying
comments together with a functional change. The change
allows function type of GPIO to select any type of enum
in their MARK lists. Without this patch only function
type of enums are allowed in MARK lists.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some codecs disable widgets used for output pins and reserve as vendor-
spec widgets. Thus we need to check the widget type and pin cap before
actually sending SET_EAPD verbs in the auto-configuration mode.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC259 has a widget NID 0x21 for the output pin, but it wasn't handled
properly in alc268_new_analog_output().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
