schedule_delayed_work() takes the delay in jiffies, not msecs. Fix the
caller sites in musb. This bug caused regressions with the cleanups
that went in for 3.14 (8ed1fb790e: "usb: musb: finish suspend/reset
work independently from musb_hub_control()").
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_port_reset() is called from musb_hub_control() which in turn holds
a spinlock, so musb_port_reset() is not allowed to call msleep().
With the asynchronous work helpers in place, this is fortunately easy to
fix by rescheduling the reset deassertion function to after the time
when the wait period is finished.
Note, however, that the MUSB_POWER_RESUME bit is only set on AM33xx
processors under rare conditions such as when to another driver
reporting an error during suspend. Hence, this didn't hit me yet in
normal operation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This interface is to be handled by the qmi_wwan driver.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
High-speed USB connections revert back to full-speed signalling when
the device goes into suspend. This takes several milliseconds, and
during that time it's not possible to tell reliably whether the device
has been disconnected.
On some platforms, the Wake-On-Disconnect circuitry gets confused
during this intermediate state. It generates a false wakeup signal,
which can prevent the controller from going to sleep.
To avoid this problem, this patch adds a 5-ms delay to the
ehci_bus_suspend() routine if any ports have to switch over to
full-speed signalling. (Actually, the delay was already present for
devices using a particular kind of PHY power management; the patch
merely causes the delay to be used more widely.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Peter Chen <Peter.Chen@freescale.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add processing for normally encountered thumb relocation types so that
section mismatches will be detected.
Comment from Rusty Russell follows:
Happiest for this to go through an ARM tree, so:
Signed-off-by: David A. Long <dave.long@linaro.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On 2-level page table systems, the PMD has 2 section entries. Report
these, otherwise ARM_PTDUMP will miss reporting permission changes on
odd section boundaries.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CP semaphore queue on CIK has a bug that triggers if uncompleted
waits use the same address while a signal is still pending. Work around
this by using different addresses for each sync.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Static checkers complain that probably curly braces were intended here,
but actually it makes more sense to remove the extra tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Most laptops seems to have a vblank period of less than
300 and mclk switching works fine. Drop the quirk and
set the default threshold to 200.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=70701
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some hardware may not support standard 64x64 cursors. Add
a drm cap to query the cursor size from the kernel. Some examples
include radeon CIK parts (128x128 cursors) and armada (32x64 or 64x32).
This allows things like device specific ddxes to remove asics specific
logic and also allows xf86-video-modesetting to work properly with hw
cursors on this hardware. Default to 64 if the driver doesn't specify
a size.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
We were already storing the bpc (bits per color) information
in radeon_crtc, so just use that everywhere rather than
calculating it everywhere we use it. This also allows us
to change it in one place if we ever want to override it.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XNON
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Miscellaneous ext4 bug fixes for v3.14"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
jbd2: fix use after free in jbd2_journal_start_reserved()
ext4: don't leave i_crtime.tv_sec uninitialized
ext4: fix online resize with a non-standard blocks per group setting
ext4: fix online resize with very large inode tables
ext4: don't try to modify s_flags if the the file system is read-only
ext4: fix error paths in swap_inode_boot_loader()
ext4: fix xfstest generic/299 block validity failures
Check always when we calculate the free dw, not just the first time.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The reason for the false positives was fixed quite some time ago and since
most engines can still execute NOPs while being locked up it leads to false
negatives.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
In all cases where it really matters we are using the read functions anyway.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Commit 3dc6475 ("bcm63xx_enet: add support Broadcom BCM6345 Ethernet")
changed the ENETDMA[CS] macros such that they are no longer macros, but
actual register offset definitions. The bcm63xx_udc driver was not
updated, and as a result, causes the following build error to pop up:
CC drivers/usb/gadget/u_ether.o
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_write':
drivers/usb/gadget/bcm63xx_udc.c:642:24: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_reset_channel':
drivers/usb/gadget/bcm63xx_udc.c:698:46: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c:700:49: error: called object '0' is not
a function
Fix this by updating usb_dmac_{read,write}l and usb_dmas_{read,write}l to
take an extra channel argument, and use the channel width
(ENETDMA_CHAN_WIDTH) to offset the register we want to access, hence
doing again what the macro implicitely did for us.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb_port_reset() is called from musb_hub_control() which in turn holds
a spinlock, so musb_port_reset() is not allowed to call msleep().
With the asynchronous work helpers in place, this is fortunately easy to
fix by rescheduling the reset deassertion function to after the time
when the wait period is finished.
Note, however, that the MUSB_POWER_RESUME bit is only set on AM33xx
processors under rare conditions such as when to another driver
reporting an error during suspend. Hence, this didn't hit me yet in
normal operation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pass value instead of address as expected by 'usb_ep_set_maxpacket_limit'.
Fixes the following compilation error introduced by commit e117e742d3
("usb: gadget: add "maxpacket_limit" field to struct usb_ep"):
drivers/usb/gadget/s3c2410_udc.c: In function ‘s3c2410_udc_reinit’:
drivers/usb/gadget/s3c2410_udc.c:1632:3: error:
cannot take address of bit-field ‘maxpacket’
usb_ep_set_maxpacket_limit(&ep->ep, &ep->ep.maxpacket);
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During resume don't touch SUSPENDM/RESUME bits of POWER register
while restoring controller context. These bits might be changed
by the controller during resume operation and so will be different
than what they were during suspend.
e.g. SUSPENDM bit is set by software during USB global suspend but
automatically cleared by the controller during remote wakeup or
during resume. Setting this bit back while restoring context
causes undesired behaviour. i.e. Babble interrupt is generated
and USB is broken.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Disables PING on status phase of control transfer.
PING token is not mandatory in status phase of control transfer
and so some high speed USB devices don't support it. If such devices
are connected to MUSB then they would not respond to PING token
causing delayed or failed enumeration.
[Roger Q] Fixes enumeration issues with some Super-Speed USB hubs
e.g. Dlink DUB-1340
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The corresponding driver didn't make it into v3.14, so we need to remove
the node. Dove systems fail to boot with the node present and no
driver.
This node will be re-added when the driver makes it to mainline.
Reported-by: Jean-Francois Moine <moinejf@free.fr>
Tested-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When restoring bi_end_io, increase bi_remaining before retrying the bio
to avoid BUG_ON(atomic_read(&bio->bi_remaining) <= 0) in bio_endio().
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Samsung's pci-e SSDs with device ID 0x1600 which are found on some
macbooks time out on NCQ commands. Blacklist NCQ on the device so
that the affected machines can at least boot.
Original-patch-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60731
Cc: stable@vger.kernel.org
Some of the vce clocks are automatic, others need to
be manually enabled. For ease, just disable cg when
vce is active.
v2: rebased
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The adds the appropriate function calls to properly re-init
vce before it's used after it has been power gated.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
enable vce states when vce is active. When vce is active,
it adjusts the currently selected state (performance, battery,
uvd, etc.)
v2: add code comments
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Only VCE 2.0 support so far.
v2: squashing multiple patches into this one
v3: add IRQ support for CIK, major cleanups,
basic code documentation
v4: remove HAINAN from chipset list
Signed-off-by: Christian König <christian.koenig@amd.com>
acpi_pci_link_allocate_irq() can return negative gsi even if
entry != NULL. For that case we have a memory leak, so free
entry before returning from acpi_pci_irq_enable() for gsi < 0.
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fix a memory leak found by cppcheck.
[drivers/gpu/drm/ttm/ttm_agp_backend.c:129]:
(error) Memory leak: agp_be
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Declare 'struct device' explicitly in ttm_page_alloc.h as this file
does not include any file declaring it. This removes the following
warning:
warning: 'struct device' declared inside parameter list
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
imx25 did not work without a firmware previously.
This patch adds a DT compatible to pass the correct data with the
default script addresses for imx25.
Add imx25 compatible to the list of compatibles in the binding
documentation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The CP semaphore queue on CIK has a bug that triggers if uncompleted
waits use the same address while a signal is still pending. Work around
this by using different addresses for each sync.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
