drivers/irqchip/irq-gic.c:53:23: warning: duplicate [noderef]
drivers/irqchip/irq-gic.c:651:6: warning: symbol 'gic_raise_softirq' was not declared. Should it be static?
drivers/irqchip/irq-gic.c:872:29: warning: symbol 'gic_irq_domain_ops' was not declared. Should it be static?
drivers/irqchip/irq-gic.c:977:12: warning: symbol 'gic_of_init' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1393981321-25721-1-git-send-email-sboyd@codeaurora.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Skip the futex_atomic_cmpxchg_inatomic() test in futex_init(). It causes a
fatal exception on 68030 (and presumably 68020 also).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: http://lkml.kernel.org/r/alpine.LNX.2.00.1403061006440.5525@nippy.intranet
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In some cases, we need regmap's format parse_val function
to do be/le translation according to the bus configuration.
For example, snd_soc_bytes_put() uses regmap to write/read values,
and use cpu_to_be() directly to covert MASK into big endian. This
is a defect, and should use regmap's format function to do it according
to bus configuration.
Signed-off-by: Nenghua Cao <nhcao@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch extends the regulator helpers to account for device that use
multiple bits for control when using regmap enable/disable/bypass ops.
The actual regulator helpers wrongly assume that the regulator control
is always performed using single bits, using in the regulator_desc
struct only two parameters *_reg and *_mask defining register and mask
for control.
This patch extends this struct and introduces the helpers to take into
account devices where control is performed using multiple bits and
specific multi-bit values are used for enabling/disabling/bypassing the
regulator.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a stub for kvm_vgic_addr when compiling without
CONFIG_KVM_ARM_VGIC. The usefulness of this configurarion is extremely
doubtful, but let's fix it anyway (until we decide that we'll always
support a VGIC).
Reported-by: Michele Paolino <m.paolino@virtualopensystems.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Z clock frequency change is effective only after setting the kick
bit located in the FRQCRB register.
Without that, the CA15 CPUs clock rate will never change.
Fix that by checking if the kick bit is cleared and enable it to make
the clock rate change effective. The bit is cleared automatically upon
completion.
Signed-off-by: Benoit Cousson <bcousson+renesas@baylibre.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
LTC2974 datasheet revision C lists the chip ID for LTC2974 as 0x0213.
Reviewed-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Previously only the resources controlled by the driver were put into
low power state at system suspend. Both the amba bus and a potential
power domain were ignored.
Moreover, while putting the device into low power state we first
brought it back to full power, but for no particular reason.
To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert to the SET_PM_RUNTIME_PM macro while defining the runtime PM
callbacks. This means the callbacks becomes available for both
CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME, which is needed to handle the
combinations of these scenarios.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
It moves the state setting for query into rndis_filter_receive_response().
All callbacks including query-complete and status-callback are synchronized
by channel->inbound_lock. This prevents pentential race between them.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating RX buffers a fixed size is used, while freeing is based
on actually received bytes, resulting in the following kernel warning
when CONFIG_DMA_API_DEBUG is enabled:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:1051 check_unmap+0x258/0x894()
macb e000b000.ethernet: DMA-API: device driver frees DMA memory with different size [device address=0x000000002d170040] [map size=1536 bytes] [unmap size=60 bytes]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.0-rc3-xilinx-00220-g49f84081ce4f #65
[<c001516c>] (unwind_backtrace) from [<c0011df8>] (show_stack+0x10/0x14)
[<c0011df8>] (show_stack) from [<c03c775c>] (dump_stack+0x7c/0xc8)
[<c03c775c>] (dump_stack) from [<c00245cc>] (warn_slowpath_common+0x60/0x84)
[<c00245cc>] (warn_slowpath_common) from [<c0024670>] (warn_slowpath_fmt+0x2c/0x3c)
[<c0024670>] (warn_slowpath_fmt) from [<c0227d44>] (check_unmap+0x258/0x894)
[<c0227d44>] (check_unmap) from [<c0228588>] (debug_dma_unmap_page+0x64/0x70)
[<c0228588>] (debug_dma_unmap_page) from [<c02ab78c>] (gem_rx+0x118/0x170)
[<c02ab78c>] (gem_rx) from [<c02ac4d4>] (macb_poll+0x24/0x94)
[<c02ac4d4>] (macb_poll) from [<c031222c>] (net_rx_action+0x6c/0x188)
[<c031222c>] (net_rx_action) from [<c0028a28>] (__do_softirq+0x108/0x280)
[<c0028a28>] (__do_softirq) from [<c0028e8c>] (irq_exit+0x84/0xf8)
[<c0028e8c>] (irq_exit) from [<c000f360>] (handle_IRQ+0x68/0x8c)
[<c000f360>] (handle_IRQ) from [<c0008528>] (gic_handle_irq+0x3c/0x60)
[<c0008528>] (gic_handle_irq) from [<c0012904>] (__irq_svc+0x44/0x78)
Exception stack(0xc056df20 to 0xc056df68)
df20: 00000001 c0577430 00000000 c0577430 04ce8e0d 00000002 edfce238 00000000
df40: 04e20f78 00000002 c05981f4 00000000 00000008 c056df68 c0064008 c02d7658
df60: 20000013 ffffffff
[<c0012904>] (__irq_svc) from [<c02d7658>] (cpuidle_enter_state+0x54/0xf8)
[<c02d7658>] (cpuidle_enter_state) from [<c02d77dc>] (cpuidle_idle_call+0xe0/0x138)
[<c02d77dc>] (cpuidle_idle_call) from [<c000f660>] (arch_cpu_idle+0x8/0x3c)
[<c000f660>] (arch_cpu_idle) from [<c006bec4>] (cpu_startup_entry+0xbc/0x124)
[<c006bec4>] (cpu_startup_entry) from [<c053daec>] (start_kernel+0x350/0x3b0)
---[ end trace d5fdc38641bd3a11 ]---
Mapped at:
[<c0227184>] debug_dma_map_page+0x48/0x11c
[<c02ab32c>] gem_rx_refill+0x154/0x1f8
[<c02ac7b4>] macb_open+0x270/0x3e0
[<c03152e0>] __dev_open+0x7c/0xfc
[<c031554c>] __dev_change_flags+0x8c/0x140
Fixing this by passing the same size which is passed during mapping the
memory to the unmap function as well.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on ec0223ec48 ("net: sctp: fix sctp_sf_do_5_1D_ce to
verify if we/peer is AUTH capable"), we noticed that there's a skb
memory leakage in the error path.
Running the same reproducer as in ec0223ec48 and by unconditionally
jumping to the error label (to simulate an error condition) in
sctp_sf_do_5_1D_ce() receive path lets kmemleak detector bark about
the unfreed chunk->auth_chunk skb clone:
Unreferenced object 0xffff8800b8f3a000 (size 256):
comm "softirq", pid 0, jiffies 4294769856 (age 110.757s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
89 ab 75 5e d4 01 58 13 00 00 00 00 00 00 00 00 ..u^..X.........
backtrace:
[<ffffffff816660be>] kmemleak_alloc+0x4e/0xb0
[<ffffffff8119f328>] kmem_cache_alloc+0xc8/0x210
[<ffffffff81566929>] skb_clone+0x49/0xb0
[<ffffffffa0467459>] sctp_endpoint_bh_rcv+0x1d9/0x230 [sctp]
[<ffffffffa046fdbc>] sctp_inq_push+0x4c/0x70 [sctp]
[<ffffffffa047e8de>] sctp_rcv+0x82e/0x9a0 [sctp]
[<ffffffff815abd38>] ip_local_deliver_finish+0xa8/0x210
[<ffffffff815a64af>] nf_reinject+0xbf/0x180
[<ffffffffa04b4762>] nfqnl_recv_verdict+0x1d2/0x2b0 [nfnetlink_queue]
[<ffffffffa04aa40b>] nfnetlink_rcv_msg+0x14b/0x250 [nfnetlink]
[<ffffffff815a3269>] netlink_rcv_skb+0xa9/0xc0
[<ffffffffa04aa7cf>] nfnetlink_rcv+0x23f/0x408 [nfnetlink]
[<ffffffff815a2bd8>] netlink_unicast+0x168/0x250
[<ffffffff815a2fa1>] netlink_sendmsg+0x2e1/0x3f0
[<ffffffff8155cc6b>] sock_sendmsg+0x8b/0xc0
[<ffffffff8155d449>] ___sys_sendmsg+0x369/0x380
What happens is that commit bbd0d59809 clones the skb containing
the AUTH chunk in sctp_endpoint_bh_rcv() when having the edge case
that an endpoint requires COOKIE-ECHO chunks to be authenticated:
---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ---------->
<------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] ---------
------------------ AUTH; COOKIE-ECHO ---------------->
<-------------------- COOKIE-ACK ---------------------
When we enter sctp_sf_do_5_1D_ce() and before we actually get to
the point where we process (and subsequently free) a non-NULL
chunk->auth_chunk, we could hit the "goto nomem_init" path from
an error condition and thus leave the cloned skb around w/o
freeing it.
The fix is to centrally free such clones in sctp_chunk_destroy()
handler that is invoked from sctp_chunk_free() after all refs have
dropped; and also move both kfree_skb(chunk->auth_chunk) there,
so that chunk->auth_chunk is either NULL (since sctp_chunkify()
allocs new chunks through kmem_cache_zalloc()) or non-NULL with
a valid skb pointer. chunk->skb and chunk->auth_chunk are the
only skbs in the sctp_chunk structure that need to be handeled.
While at it, we should use consume_skb() for both. It is the same
as dev_kfree_skb() but more appropriately named as we are not
a device but a protocol. Also, this effectively replaces the
kfree_skb() from both invocations into consume_skb(). Functions
are the same only that kfree_skb() assumes that the frame was
being dropped after a failure (e.g. for tools like drop monitor),
usage of consume_skb() seems more appropriate in function
sctp_chunk_destroy() though.
Fixes: bbd0d59809 ("[SCTP]: Implement the receive and verification of AUTH chunk")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Vlad Yasevich <yasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are known issues for switching the drivers between ECM mode and
vendor mode. The interrup transfer may become abnormal. The hardware
may have the opportunity to die if you change the configuration without
unloading the current driver first, because all the control transfers
of the current driver would fail after the command of switching the
configuration.
Although to use the ecm driver and vendor driver independently is fine,
it may have problems to change the driver from one to the other by
switching the configuration. Additionally, now the vendor mode driver
is more powerful than the ECM driver. Thus, disable the ECM mode driver,
and let r8152 to set the configuration to vendor mode and reset the
device automatically.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kexec scenario, we failed to load the mlx4 driver in the
second kernel because the ownership bit was hold by the first
kernel without release correctly.
The patch adds shutdown() interface so that the ownership can
be released correctly in the first kernel. It also helps avoiding
EEH error happened during boot stage of the second kernel because
of undesired traffic, which can't be handled by hardware during
that stage on Power platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Tested-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MLD queries are supposed to have an IPv6 link-local source address
according to RFC2710, section 4 and RFC3810, section 5.1.14. This patch
adds a sanity check to ignore such broken MLD queries.
Without this check, such malformed MLD queries can result in a
denial of service: The queries are ignored by any MLD listener
therefore they will not respond with an MLD report. However,
without this patch these malformed MLD queries would enable the
snooping part in the bridge code, potentially shutting down the
according ports towards these hosts for multicast traffic as the
bridge did not learn about these listeners.
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I stumbled upon this very serious bug while hunting for another one,
it's a very subtle race condition between inet_frag_evictor,
inet_frag_intern and the IPv4/6 frag_queue and expire functions
(basically the users of inet_frag_kill/inet_frag_put).
What happens is that after a fragment has been added to the hash chain
but before it's been added to the lru_list (inet_frag_lru_add) in
inet_frag_intern, it may get deleted (either by an expired timer if
the system load is high or the timer sufficiently low, or by the
fraq_queue function for different reasons) before it's added to the
lru_list, then after it gets added it's a matter of time for the
evictor to get to a piece of memory which has been freed leading to a
number of different bugs depending on what's left there.
I've been able to trigger this on both IPv4 and IPv6 (which is normal
as the frag code is the same), but it's been much more difficult to
trigger on IPv4 due to the protocol differences about how fragments
are treated.
The setup I used to reproduce this is: 2 machines with 4 x 10G bonded
in a RR bond, so the same flow can be seen on multiple cards at the
same time. Then I used multiple instances of ping/ping6 to generate
fragmented packets and flood the machines with them while running
other processes to load the attacked machine.
*It is very important to have the _same flow_ coming in on multiple CPUs
concurrently. Usually the attacked machine would die in less than 30
minutes, if configured properly to have many evictor calls and timeouts
it could happen in 10 minutes or so.
An important point to make is that any caller (frag_queue or timer) of
inet_frag_kill will remove both the timer refcount and the
original/guarding refcount thus removing everything that's keeping the
frag from being freed at the next inet_frag_put. All of this could
happen before the frag was ever added to the LRU list, then it gets
added and the evictor uses a freed fragment.
An example for IPv6 would be if a fragment is being added and is at
the stage of being inserted in the hash after the hash lock is
released, but before inet_frag_lru_add executes (or is able to obtain
the lru lock) another overlapping fragment for the same flow arrives
at a different CPU which finds it in the hash, but since it's
overlapping it drops it invoking inet_frag_kill and thus removing all
guarding refcounts, and afterwards freeing it by invoking
inet_frag_put which removes the last refcount added previously by
inet_frag_find, then inet_frag_lru_add gets executed by
inet_frag_intern and we have a freed fragment in the lru_list.
The fix is simple, just move the lru_add under the hash chain locked
region so when a removing function is called it'll have to wait for
the fragment to be added to the lru_list, and then it'll remove it (it
works because the hash chain removal is done before the lru_list one
and there's no window between the two list adds when the frag can get
dropped). With this fix applied I couldn't kill the same machine in 24
hours with the same setup.
Fixes: 3ef0eb0db4 ("net: frag, move LRU list maintenance outside of
rwlock")
CC: Florian Westphal <fw@strlen.de>
CC: Jesper Dangaard Brouer <brouer@redhat.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The menu governor performance multiplier defines a minimum predicted
idle duration to latency ratio. Instead of checking this separately
in every iteration of the state selection loop, adjust the overall
latency restriction for the whole loop if this restriction is tighter
than what is set by the QoS subsystem.
The original test
s->exit_latency * multiplier > data->predicted_us
becomes
s->exit_latency > data->predicted_us / multiplier
by dividing both sides of the comparison by "multiplier".
While division is likely to be several times slower than multiplication,
the minor performance hit allows making a generic sleep state selection
function based on (sleep duration, maximum latency) tuple.
Signed-off-by: Tuukka Tikkanen <tuukka.tikkanen@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The menu governor statistics update function tries to determine the
amount of time between entry to low power state and the occurrence
of the wakeup event. However, the time measured by the framework
includes exit latency on top of the desired value. This exit latency
is substracted from the measured value to obtain the desired value.
When measured value is not available, the menu governor assumes
the wakeup was caused by the timer and the time is equal to remaining
timer length. No exit latency should be substracted from this value.
This patch prevents the erroneous substraction and clarifies the
associated comment. It also removes one intermediate variable that
serves no purpose.
Signed-off-by: Tuukka Tikkanen <tuukka.tikkanen@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The menu governor uses coefficients as one method of actual idle
period length estimation. The coefficients are, as detailed below,
multipliers giving expected idle period length from time until next
timer expiry. The multipliers are supposed to have domain of (0..1].
The coefficients are fractions where only the numerators are stored
and denominators are a shared constant RESOLUTION*DECAY. Since the
value of the coefficient should always be greater than 0 and less
than or equal to 1, the numerator must have a value greater than
0 and less than or equal to RESOLUTION*DECAY.
If the coefficients are updated with measured idle durations exceeding
timer length, the multiplier may reach values exceeding unity (i.e.
the stored numerator exceeds RESOLUTION*DECAY). This patch ensures that
the multipliers are updated with durations capped to timer length.
Signed-off-by: Tuukka Tikkanen <tuukka.tikkanen@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently menu governor records the exit latency of the state it has
chosen for the idle period. The stored latency value is then later
used to calculate the actual length of the idle period. This value
may however be incorrect, as the entered state may not be the one
chosen by the governor. The entered state information is available,
so we can use that to obtain the real exit latency.
Signed-off-by: Tuukka Tikkanen <tuukka.tikkanen@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The field expected_us is used to store the time remaining until next
timer expiry. The name is inaccurate, as we really do not expect all
wakeups to be caused by timers. In addition, another field with a very
similar name (predicted_us) is used to store the predicted time
remaining until any wakeup source being active.
This patch renames expected_us to next_timer_us in order to better
reflect the contained information.
Signed-off-by: Tuukka Tikkanen <tuukka.tikkanen@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Only CF9_COND is appropriate for inclusion in the default chain, not
CF9; the latter will poke that register unconditionally, whereas
CF9_COND will at least look for PCI configuration method #1 or #2
first (a weak check, but better than nothing.)
CF9 should be used for explicit system configuration (command line or
DMI) only.
Cc: Aubrey Li <aubrey.li@intel.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Link: http://lkml.kernel.org/r/53130A46.1010801@linux.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Reboot is the last service linux OS provides to the end user. We are
supposed to make this function more robust than today. This patch adds
all of the known reboot methods into the default attempt list. The
machines requiring reboot=efi or reboot=p or reboot=bios get a chance
to reboot automatically now.
If there is a new reboot method emerged, we are supposed to add it to
the default list as well, instead of adding the endless dmidecode entry.
If one method required is in the default list in this patch but the
machine reboot still hangs, that means some methods ahead of the
required method cause the system hangs, then reboot the machine by
passing reboot= arguments and submit the reboot dmidecode table quirk.
We are supposed to remove the reboot dmidecode table from the kernel,
but to be safe, we keep it. This patch prevents us from adding more.
If you happened to have a machine listed in the reboot dmidecode
table and this patch makes reboot work on your machine, please submit
a patch to remove the quirk.
The default reboot order with this patch is now:
ACPI > KBD > ACPI > KBD > EFI > CF9_COND > BIOS
Because BIOS and TRIPLE are mutually exclusive (either will either
work or hang the machine) that method is not included.
[ hpa: as with any changes to the reboot order, this patch will have
to be monitored carefully for regressions. ]
Signed-off-by: Aubrey Li <aubrey.li@intel.com>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Link: http://lkml.kernel.org/r/53130A46.1010801@linux.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
i) by the time DM core calls the postsuspend hook the dm_noflush flag
has been cleared. So the old thin_postsuspend did nothing. We need to
use the presuspend hook instead.
ii) There was a race between bios leaving DM core and arriving in the
deferred queue.
thin_presuspend now sets a 'requeue' flag causing all bios destined for
that thin to be requeued back to DM core. Then it requeues all held IO,
and all IO on the deferred queue (destined for that thin). Finally
postsuspend clears the 'requeue' flag.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The spin lock in requeue_io() was held for too long, allowing deadlock.
Don't worry, due to other issues addressed in the following "dm thin:
fix noflush suspend IO queueing" commit, this code was never called.
Fix this by taking the spin lock for a much shorter period of time.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Ideally a thin pool would never run out of data space; the low water
mark would trigger userland to extend the pool before we completely run
out of space. However, many small random IOs to unprovisioned space can
consume data space at an alarming rate. Adjust your low water mark if
you're frequently seeing "out-of-data-space" mode.
Before this fix, if data space ran out the pool would be put in
PM_READ_ONLY mode which also aborted the pool's current metadata
transaction (data loss for any changes in the transaction). This had a
side-effect of needlessly compromising data consistency. And retry of
queued unserviceable bios, once the data pool was resized, could
initiate changes to potentially inconsistent pool metadata.
Now when the pool's data space is exhausted transition to a new pool
mode (PM_OUT_OF_DATA_SPACE) that allows metadata to be changed but data
may not be allocated. This allows users to remove thin volumes or
discard data to recover data space.
The pool is no longer put in PM_READ_ONLY mode in response to the pool
running out of data space. And PM_READ_ONLY mode no longer aborts the
pool's current metadata transaction. Also, set_pool_mode() will now
notify userspace when the pool mode is changed.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If a thin metadata operation fails the current transaction will abort,
whereby causing potential for IO layers up the stack (e.g. filesystems)
to have data loss. As such, set THIN_METADATA_NEEDS_CHECK_FLAG in the
thin metadata's superblock which:
1) requires the user verify the thin metadata is consistent (e.g. use
thin_check, etc)
2) suggests the user verify the thin data is consistent (e.g. use fsck)
The only way to clear the superblock's THIN_METADATA_NEEDS_CHECK_FLAG is
to run thin_repair.
On metadata operation failure: abort current metadata transaction, set
pool in read-only mode, and now set the needs_check flag.
As part of this change, constraints are introduced or relaxed:
* don't allow a pool to transition to write mode if needs_check is set
* don't allow data or metadata space to be resized if needs_check is set
* if a thin pool's metadata space is exhausted: the kernel will now
force the user to take the pool offline for repair before the kernel
will allow the metadata space to be extended.
Also, update Documentation to include information about when the thin
provisioning target commits metadata, how it handles metadata failures
and running out of space.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
If the open stateid could not be recovered, or the file locks were lost,
then we should fail the truncate() operation altogether.
Reported-by: Andy Adamson <andros@netapp.com>
Link: http://lkml.kernel.org/r/1393954269-3974-1-git-send-email-andros@netapp.com
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
In commit 5521abfdcf (NFSv4: Resend the READ/WRITE RPC call
if a stateid change causes an error), we overloaded the return value of
nfs4_select_rw_stateid() to cause it to return -EWOULDBLOCK if an RPC
call is outstanding that would cause the NFSv4 lock or open stateid
to change.
That is all redundant when we actually copy the stateid used in the
read/write RPC call that failed, and check that against the current
stateid. It is doubly so, when we consider that in the NFSv4.1 case,
we also set the stateid's seqid to the special value '0', which means
'match the current valid stateid'.
Reported-by: Andy Adamson <andros@netapp.com>
Link: http://lkml.kernel.org/r/1393954269-3974-1-git-send-email-andros@netapp.com
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
When nfs4_set_rw_stateid() can fails by returning EIO to indicate that
the stateid is completely invalid, then it makes no sense to have it
trigger a retry of the READ or WRITE operation. Instead, we should just
have it fall through and attempt a recovery.
This fixes an infinite loop in which the client keeps replaying the same
bad stateid back to the server.
Reported-by: Andy Adamson <andros@netapp.com>
Link: http://lkml.kernel.org/r/1393954269-3974-1-git-send-email-andros@netapp.com
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Avoid leaking data by sending uninitialized memory and setting an
invalid (non-zero) fragment number (the sequence number is ignored
anyway) by setting the seq_ctrl field to zero.
Cc: stable@vger.kernel.org
Fixes: 3f52b7e328 ("mac80211: mesh power save basics")
Fixes: ce662b44ce ("mac80211: send (QoS) Null if no buffered frames")
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Compiling last minute changes without setting the proper config
options is not really clever.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
commit: 8f945a33 (genirq: Move kstat_incr_irqs_this_cpu() to core)
unearthed the following:
arch/m68k/kernel/ints.c:34:15: error: variable 'auto_irq_chip' has initializer but incomplete type
arch/m68k/kernel/ints.c:35:2: error: unknown field 'name' specified in initializer
arch/m68k/kernel/ints.c:35:2: warning: excess elements in struct initializer [enabled by default]
The reason is that this file requires linux/irq.h and magically
pulled that in via linux/kernel_stat.h
The commit above got rid of the pointless include of linux/irq.h in
linux/kernel_stat.h and therefor broke the build.
Include linux/irq.h
Reported-by: fengguang.wu@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Logitech C500 (046d:0807) needs the same workaround like other
Logitech Webcams.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For making the driver behavior compatible with the earlier kernels,
use the analog beep in the loopback path instead of the digital beep.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mixer widget (NID 0x20) of AD1884 and AD1984 codecs isn't
connected directly to the actual I/O paths but only via another mixer
widget (NID 0x21). We need a similar fix as we did for AD1882.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kbuild test robot reported the following errors, introduced with
commit 54b52d8726 ("x86/efi: Build our own EFI services pointer
table"),
arch/x86/boot/compressed/head_32.o: In function `efi32_config':
>> (.data+0x58): undefined reference to `efi_call_phys'
arch/x86/boot/compressed/head_64.o: In function `efi64_config':
>> (.data+0x90): undefined reference to `efi_call6'
Wrap the efi*_config structures in #ifdef CONFIG_EFI_STUB so that we
don't make references to EFI functions if they're not compiled in.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The kbuild test robot reported the following errors that were introduced
with commit 993c30a04e ("x86, tools: Consolidate #ifdef code"),
arch/x86/boot/tools/build.c: In function 'update_pecoff_setup_and_reloc':
>> arch/x86/boot/tools/build.c:252:1: error: parameter name omitted
static inline void update_pecoff_setup_and_reloc(unsigned int) {}
^
arch/x86/boot/tools/build.c: In function 'update_pecoff_text':
>> arch/x86/boot/tools/build.c:253:1: error: parameter name omitted
static inline void update_pecoff_text(unsigned int, unsigned int) {}
^
>> arch/x86/boot/tools/build.c:253:1: error: parameter name omitted
arch/x86/boot/tools/build.c: In function 'main':
>> arch/x86/boot/tools/build.c:372:2: warning: implicit declaration of function 'efi_stub_entry_update' [-Wimplicit-function-declaration]
efi_stub_entry_update();
^
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
