clock offset may be set and read in decimal parts per billion
attribute is /sys/class/rtc/rtcN/offset
The attribute is only visible for rtcs that have set_offset implemented.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
A number of rtc devices, such as the NXP pcf2123 include a facility
to adjust the clock in order to compensate for temperature or a
crystal, capacitor, etc, that results in the rtc clock not running
at exactly 32.768 kHz.
Data sheets I have seen refer to this as a clock offset, and measure it
in parts per million, however they often reference ppm to 2 digits of
precision, which makes integer ppm less than ideal.
We use parts per billion, which more than covers the precision needed
and works nicely within 32 bits
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix a scheduling while atomic issue caused by rv8803_set_time()
holding a spinlock during the call to i2c_smbus_read_byte_data().
Signed-off-by: Oleksij Rempel <fixed-term.Oleksij.Rempel@de.bosch.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add support for RTC controller found on Alphascale asm9260
SoC.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
DS3231 has programmable square-wave output signal.
This enables to use this feature as a clock provider of
common clock framework.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
To make RTC block of MAX77686/MAX77802 as independent driver,
move the registration of i2c device, regmap for register access
and irq_chip for interrupt support inside the RTC driver.
Removed the same initialisation from MFD driver.
Having this change will allow to reuse this driver for different
PMIC/devices from Maxim Semiconductor if they kept same RTC IP on
different PMIC. Some of examples as PMIC MAX77620, MAX20024 where
same RTC IP used and hence driver for these chips will use this
driver only for RTC support.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There is different RTC I2C address for RTC block in MAX77686.
Driver is creating dummy i2c client for this address to access
the register of this IP block.
As there is no call to i2c_get_clientdata() for rtc_i2c client,
there is no need to store pointer and hence removing the call
to set client data for rtc i2c client.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Get rid of referring parent device info for register access
all the places by making regmap as part of max77686 rtc
device info. This will also remove the need of storing parent
device info in max77686 rtc device info as this is no more required.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc_regmap should be used to access all RTC registers instead
of parent regmap regardless of what chip or property have it.
This makes the register access uniform and extendible for other
chips.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix following check patch error in rtc-max77686 driver:
- Alignment should match open parenthesis.
- braces {} should be used on all arms of this statement.
- Prefer using the BIT macro
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
At the moment the "sun6i" RTC drivers depends on having two specific
SoC families selected.
The Allwinner A64 SoC has the same RTC, so extend the Kconfig option
to allow inclusion of the driver for all Allwinner SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RX6110 comes in two different variants: SPI and I2C.
This driver only supports the SPI variant.
If the need ever arises to also support the I2C variant, this driver
could easily be refactored to support both cases.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add the binding documentation for the Epson RX6110 RTC.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf2123 data sheet recommends a software reset when the chip
is first powered on. This change avoids resetting the chip
every time the driver is loaded, which has some negative effects.
There are several registers including a clock rate adjustment that really
should survive a reload of the driver (or reboot).
In addition, stopping and restarting the clock to verify the chip is
there is not a good thing once the time is set.
According to the data sheet, the seconds register has a 1 in
the high bit when the voltage has gotten low. We check for this
condition, as well as whether the time retrieved from the chip is
valid. We reset the rtc only if the time is not reliable and valid.
This is sufficient for checking for the presence of the chip,
as either all zeros or all 0xff will result in an invalid time/date
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Refactor chip reset items into its own function, isolating it from
the rest of the device probe.
Subsequent commits will avoid calling this code.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add new functions pcf2123_write(), and pcf2123_write_reg().
Use named defines for the values being written.
This improves modularity and readability, and reduces lines of code.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Put read operations into a function.
This improves modularity and readability.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add defines for all 16 registers in the pcf2123.
Add defines for useful bits from several registers
I've tried to document all the registers, and
as best as possible, all the special bits they employ
Use BIT() wherever possible in the bit definitions
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The function measurement block must not cross a page boundary. Ensure
that by raising the alignment requirement to the smallest power of 2
larger than the size of the fmb.
Fixes: d0b088531 ("s390/pci: performance statistics and debug infrastructure")
Cc: stable@vger.kernel.org # v3.8+
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We disabled the ability to enable this driver back in October of 2013,
we should be able to safely remove it at this point. The initial goal
was to remove it in 3.15, so now is the time.
Signed-off-by: Jens Axboe <axboe@fb.com>
We use bio chaining during most I/Os these days due to the delayed
bio splitting. Additionally XFS will start using it, and there is
a pending direct I/O rewrite also making heavy use for it. Don't
pretend it's always unlikely, and let the branch predictor do it's
job instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Replace the while loop that unecessarily checks for a NULL bio in the fast
path with a simple goto loop.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Factor common code between bio_chain_endio and bio_endio into a common
helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Only overwrite the parents bi_error if it was zero. That way a successful
bio completion doesn't reset the error pointer.
Reported-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The iBFT table only specifies a prefix length, not a netmask.
And the netmask is pretty much pointless for IPv6.
So introduce a new attribute 'prefix-len'.
Some older user-space code might rely on the netmask attribute
being present, so we should always display it.
Changes from v1:
- Combined two patches into one
Changes from v2:
- Cleaned up/corrected wording for patch description
v3: [Put Hannes back as author]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
* pm-cpufreq: (94 commits)
intel_pstate: Do not skip samples partially
intel_pstate: Remove freq calculation from intel_pstate_calc_busy()
intel_pstate: Move intel_pstate_calc_busy() into get_target_pstate_use_performance()
intel_pstate: Optimize calculation for max/min_perf_adj
intel_pstate: Remove extra conversions in pid calculation
cpufreq: Move scheduler-related code to the sched directory
Revert "cpufreq: postfix policy directory with the first CPU in related_cpus"
cpufreq: Reduce cpufreq_update_util() overhead a bit
cpufreq: Select IRQ_WORK if CPU_FREQ_GOV_COMMON is set
cpufreq: Remove 'policy->governor_enabled'
cpufreq: Rename __cpufreq_governor() to cpufreq_governor()
cpufreq: Relocate handle_update() to kill its declaration
cpufreq: governor: Drop unnecessary checks from show() and store()
cpufreq: governor: Fix race in dbs_update_util_handler()
cpufreq: governor: Make gov_set_update_util() static
cpufreq: governor: Narrow down the dbs_data_mutex coverage
cpufreq: governor: Make dbs_data_mutex static
cpufreq: governor: Relocate definitions of tuners structures
cpufreq: governor: Move per-CPU data to the common code
cpufreq: governor: Make governor private data per-policy
...
* acpi-pci:
x86/ACPI/PCI: Recognize that Interrupt Line 255 means "not connected"
* acpi-soc:
i2c: designware: Add device HID for future AMD I2C controller
* pnp:
PNP / ACPI: add ACPI_RESOURCE_TYPE_SERIAL_BUS as a valid type
* acpi-processor:
ACPI / sleep: move acpi_processor_sleep to sleep.c
ACPI / processor : add support for ACPI0010 processor container
ACPI / processor_idle: replace PREFIX with pr_fmt
* acpi-cppc:
ACPI / CPPC: use MRTT/MPAR to decide if/when a req can be sent
ACPI / CPPC: replace writeX/readX to PCC with relaxed version
mailbox: pcc: optimized pcc_send_data
ACPI / CPPC: optimized cpc_read and cpc_write
ACPI / CPPC: Optimize PCC Read Write operations
* acpi-scan:
ACPI / scan: AMBA bus probing support
ACPI: introduce a function to find the first physical device
* acpi-osl:
ACPI / OSL: Add support to install tables via initrd
ACPI / OSL: Clean up initrd table override code
* acpi-apei:
ACPI / APEI: ERST: Fixed leaked resources in erst_init
ACPI / APEI: Fix leaked resources
* acpica:
ACPICA / Interpreter: Fix a regression triggered because of wrong Linux ECDT support
ACPICA: Utilities: Update trace mechinism for acquire_object
ACPICA: Namespace: Rename acpi_gbl_reg_methods_enabled to acpi_gbl_namespace_initialized
ACPICA: Namespace: Ensure \_SB._INI executed before any _REG
ACPICA: ACPICA: Tune _REG evaluations order in the initialization steps
ACPICA: Tables: make default region accessible during the table load
ACPICA: ACPI 6.0/iASL: Add support for the External AML opcode
ACPICA: Remove unnecessary arguments to ACPI_INFO
ACPICA: debugger: dbconvert: free pld_info on error return path
ACPICA: iASL: Update to use internal acpi_ut_strtoul64 function
ACPICA: iASL: Fix some typos with the name strtoul64
ACPICA: Remove incorrect "static" from a global structure
ACPICA: aclocal: Put parens around some definitions.
The main thing in terms of the core this time around has been some
additional framework work for dynamic topologies (though we *still*
don't appear to have a stable ABI for the topology code, it's probably
worth considering if this will ever happen...). Otherwise the work has
almost all been in the drivers:
- HDMI support for Sky Lake, along with other fixes and enhancements
for the Intel drivers.
- Lots of improvements to the Renesas drivers.
- Capture support for Qualcomm drivers.
- Support for TI DaVinci DRA7xxx devices.
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs.
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW5qP+AAoJECTWi3JdVIfQJhAH/RKv268gjE07uJ8jeGAT7uY4
XM19VmUl7ZOlphctfr/I+1hRwo+mgGN4LSfKnXxsPk9Uq/WJUok4D7MjDN33jeX/
heK9WAO8zXkgi9n2lhGI/z9uE76kPA/Qw0aEYcbmA6bDc4GF3AKphnByh6kDShtE
BfblofsFaDywA09XQ2lh3wW0rZtJ51tQUeOi35UADyEPzQetzN+xiY85Bkia5BEt
Yjp37nLJET8Gk0r9snE2MpACUkEyw7CiPXCjkK47npia41LVnTarZAq5+JmfKygg
YV2EnC3AFYthhjZPfmO1usI2vJVwkN40nGrKipH2QX08TanK8r2qiTsmGADNX4E=
=0/1R
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.6
The main thing in terms of the core this time around has been some
additional framework work for dynamic topologies (though we *still*
don't appear to have a stable ABI for the topology code, it's probably
worth considering if this will ever happen...). Otherwise the work has
almost all been in the drivers:
- HDMI support for Sky Lake, along with other fixes and enhancements
for the Intel drivers.
- Lots of improvements to the Renesas drivers.
- Capture support for Qualcomm drivers.
- Support for TI DaVinci DRA7xxx devices.
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs.
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514.
If the 'old' operand to cmpxchg() is a constant wider than 21 bits,
linking fails with a "relocation truncated to fit: R_AVR32_21S" error.
Fix this by replacing the "i" constraint with "Ks21" which makes the
compiler use a temporary register for out of range constants.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
This patch wires up the new copy_file_range syscall on AVR32.
On AVR32, all parameters beyond the 5th are passed on the stack. System
calls don't use the stack -- they borrow a callee-saved register
instead. This means that syscalls that take 6 parameters must be called
through a stub that pushes the last parameter on the stack.
Signed-off-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Freescale updates from Scott:
"Highlights include 8xx optimizations, 32-bit checksum optimizations,
86xx consolidation, e5500/e6500 cpu hotplug, more fman and other dt
bits, and minor fixes/cleanup."
When resetting a device (especially after power loss) it is unlikely
that the firmware will keep the contact tracking data for the previous
touches and will be able to reconcile it with the new contacts, so
let's release all slots on reset resume as start anew.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
led_trigger_store can be significantly simplified by using sysfs_streq().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata in probe function and the remove
function, max8997_led_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata in probe function and the remove
function, da903x_led_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove unnecessary function pdev_to_gpio, platform_set_drvdata
in the probe function and the remove function, s3c24xx_led_remove as
it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata from probe function and the remove
function, wm831x_status_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata in probe function and the remove
function, lp8788_led_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata in probe function and the remove
function, pm860x_led_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Si-En Technology was acquired by ISSI in 2011, and it appears that
the IS31FL3218/IS31FL3216 are just rebranded SN3218/SN3216 devices.
Add the "si-en,sn3218" and "si-en,sn3216" compatible strings into the
IS31FL32XX driver as aliases for the issi equivalents, and update
binding documentation.
Datasheets:
IS31FL3218: http://www.issi.com/WW/pdf/31FL3218.pdf
SN3218: http://www.si-en.com/uploadpdf/s2011517171720.pdf
IS31FL3216: http://www.issi.com/WW/pdf/31FL3216.pdf
SN3216: http://www.si-en.com/uploadpdf/SN3216201152410148.pdf
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
