and update pci_ids.h to include new PCI ID for StorageWorks 1210m variant.
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is done by adding support for the so-called "performant mode"
(that's really what they called it). Smart Array controllers
have a mode which enables multiple command completions to be
delivered with a single interrupt, "performant" mode. We want to use
that mode, as some newer controllers will be requiring this mode.
Signed-off-by: Don Brace <brace@beardog.cce.hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
That is, use u64, u32, u16 and u8 rather than __u64, __u32, __u16 and __u8.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
driver fixed the device update issue after get the AEN PD delete/ADD
and LD add/delete from FW.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver issue the get ld list to fw to get the logic drive list.
Driver will keep the logic drive list for the internal use after
driver load.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add the pad_0 in mfi frame structure to 0 to fix the context value
larger than 32bit value issue.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The check for a valid mux name should be performed regardless of whether
DEBUG_FS is enabled or not. Otherwise without DEBUG_FS, we get:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
last sysfs file:
Modules linked in:
CPU: 0 Not tainted (2.6.33-rc8 #10)
PC is at strcmp+0x18/0x40
LR is at omap_mux_init_signal+0x68/0x14c
...
This fixes the issue currently seen with boards not booting up
if DEBUG_FS is not enabled in defconfig.
Note that the earlier ifndef + ifdef now becomes simpler ifdef else:
If CONFIG_OMAP_MUX is selected, we use pin names. If it's not selected,
we only want the GPIO to mux register mapping.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently we're gracefully tearing down each active connection
when fcoe.ko is removed. We shouldn't allow the user to destroy
connections by removing the module. We should force the user to
destroy each connection and then the module can be removed.
This patch makes it so a refrerence count on the module is taken
each time a fcoe_interface is created. The reference count
is dropped when the fcoe_interface is destroyed. This makes it
so that module_exit() doesn't get called unless all fcoe_interfaces
have been destroyed.
This patch leaves the removal of interfaces in the module_exit
routine so that if the user does a 'rmmod -f' we'll clean everything
up before removing the module.
The module_put line was put before the out_putdev goto line because
we should only be decrementing the reference count if a
fcoe_interface is actually destroyed. If we can't find the netdev
or the fcoe_interface then it's assumed that something else has
destroyed the fcoe_interface and it would have decremented the
reference count at that time.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
libfcoe module doesnt send port keep alive every
FIP_VN_KA_PERIOD due to improper assignment of timeout value.
Update the port_ka_time appropriately by incrementing it by
FIP_VN_KA_PERIOD in fcoe_ctlr_timeout(), so that the link_work
is scheduled to send the port LKA.
Signed-off-by: Bhanu Gollapudi <bprakash@broadcom.com>
Acked-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix NULL pointer dereference crash occurs in fc_lport_bsg_request()
for bsg requests that do not contain a response request.
Specifically, FC_BSG_HST_ADD_RPORT and FC_BSG_HST_DEL_RPORT bsg
requests are not guaranteed to include a response request.
Signed-off-by: Hugh Daschbach <hdasch@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Both PLOGI and RTV response processing conditionally scale e_d_tov,
but use different scaling factors. The scaling factor is correct in
RTV response processing. Bring PLOGI e_d_tov scaling in line with RTV
common service parameter inspection.
Signed-off-by: Hugh Daschbach <hdasch@broadcom.com>
Acked-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adds check to call fc_fcp_ddp_setup for only FCP read cmds to avoid
accessing junk fsp pointer at least in ESX since non FCP frame had
junk fsp value, though fsp is implicitly initialized to null
by __alloc_skb but with this patch no more relying on fsp
initialized to null value and hitting junk fsp ptr access.
Removes fsp pointer checking in fc_fcp_ddp_setup as this is not
needed any more since its only caller for FCP read will always
have a valid fsp.
Reported by: Frank Zhang <frank_1.zhang@intel.com>
Reported by: Rob Love <robert.w.love@intel.com>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
An empty r2tqueue is a valid state. It just means that we have
processed all that there was to do. This patch removes the WARN_ON
that was added when the kfifo changes were merged.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the initialization of USB interface pointers from _start()
over to _probe() callback, which is where it belongs.
This fixes case where interface is NULL when parsing of report
descriptor fails.
LKML-Reference: <20100213135720.603e5f64@neptune.home>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This implements some locking for the PMB code. A high level rwlock is
added for dealing with rw accesses on the entry map while a per-entry
data structure spinlock is added to deal with the PMB entry changing out
from underneath us.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Write-through PMB mappings still require the cache bit to be set, even if
they're to be flagged with a different cache policy and bufferability
bit. To reduce some of the confusion surrounding the flag encoding we
centralize the cache mask based on the system cache policy while we're at
it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in entry sizing support for existing mappings and then builds
on top of that for linking together entries that are mapping contiguous
areas. This will ultimately permit us to coalesce mappings and promote
head pages while reclaiming PMB slots for dynamic remapping.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that joystick button usages can expand over 15 buttons, we
have to properly mask out the code from hid usage to cover the
whole 0xffff available space.
Reported-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds some helper routines for uncached mapping support. This
simplifies some of the cases where we need to check the uncached mapping
boundaries in addition to giving us a centralized location for building
more complex manipulation on top of.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some overdue cleanup of the PMB code, killing off unused functionality
and duplication sprinkled about the tree.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Both the store queue API and the PMB remapping take unsigned long for
their pgprot flags, which cuts off the extended protection bits. In the
case of the PMB this isn't really a problem since the cache attribute
bits that we care about are all in the lower 32-bits, but we do it just
to be safe. The store queue remapping on the other hand depends on the
extended prot bits for enabling userspace access to the mappings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7723 INTC tables with force_enable support
to mask out pending unsupported SDHI interrupt sources.
Without this patch the kernel locks up due to a pending
SDHI interrupt that the tmio_mmc driver cannot handle.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7722 INTC tables with force_enable support
to mask out pending unsupported SDHI interrupt sources.
Without this patch the kernel locks up due to a pending
SDHI interrupt that the tmio_mmc driver cannot handle.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently there's an ordering issue with the chained handler change
which places the set_irq_chip() after set_irq_chained_handler(). This
causes a warning to be emitted as the IRQ chip needs to be set first.
However, there is the caveat that redirect IRQs can't use the parent
IRQ's irq chip as they are just dummy redirects, resulting in
intc_enable() blowing up when set_irq_chained_handler() attempts to
start up the redirect IRQ. In these cases we can just use dummy_irq_chip
directly, as we already extract the parent IRQ and chip from the redirect
handler.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
vmemmap and the vmsplit code amongst others need to be able to take page
faults much earlier than trap_init() time, so move this in to the early
CPU initialization. VBR setup for secondary CPUs is already handled
through start_secondary(), so we only need to do this for the boot CPU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: gadget: fix EEM gadget CRC usage
USB: otg Kconfig: let USB_OTG_UTILS select USB_ULPI option
USB: g_multi: fix CONFIG_USB_G_MULTI_RNDIS usage
kfifo: Don't use integer as NULL pointer
USB: FHCI: Fix build after kfifo rework
kfifo: Make kfifo_initialized work after kfifo_free
USB: serial: add usbid for dell wwan card to sierra.c
USB: SIS USB2VGA DRIVER: support KAIREN's USB VGA adaptor USB20SVGA-MB-PLUS
USB: ehci: phy low power mode bug fixing
USB: s3c-hsotg: Export usb_gadget_register_driver()
USB: r8a66597-udc: Prototype IS_ERR() and PTR_ERR()
USB: ftdi_sio: add device IDs (several ELV, one Mindstorms NXT)
USB: storage: Remove unneeded SC/PR from unusual_devs.h
USB: ftdi_sio: new device id for papouch AD4USB
USB: usbfs: properly clean up the as structure on error paths
USB: usbfs: only copy the actual data received
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
class: Free the class private data in class_release
sysfs: sysfs_sd_setattr set iattrs unconditionally
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (22 commits)
be2net: set proper value to version field in req hdr
xfrm: Fix xfrm_state_clone leak
ipcomp: Avoid duplicate calls to ipcomp_destroy
ethtool: allow non-admin user to read GRO settings.
ixgbe: fix WOL register setup for 82599
ixgbe: Fix - Do not allow Rx FC on 82598 at 1G due to errata
sfc: Fix SFE4002 initialisation
mac80211: fix handling of null-rate control in rate_control_get_rate
inet: Remove bogus IGMPv3 report handling
iwlwifi: fix AMSDU Rx after paged Rx patch
tcp: fix ICMP-RTO war
via-velocity: Fix races on shared interrupts
via-velocity: Take spinlock on set coalesce
via-velocity: Remove unused IRQ status parameter from rx_srv and tx_srv
rtl8187: Add new device ID
iwmc3200wifi: Test of wrong pointer after kzalloc in iwm_mlme_update_bss_table()
ath9k: Fix sequence numbers for PAE frames
mac80211: fix deferred hardware scan requests
iwlwifi: Fix to set correct ht configuration
mac80211: Fix probe request filtering in IBSS mode
...
When controlling an industrial radio modem it can be necessary to
manipulate the handshake lines in order to control the radio modem's
transmitter, from userspace.
The transmitter should not be turned off before all characters have been
transmitted. serial8250_tx_empty() was reporting that all characters were
transmitted before they actually were.
===
Discovered in parallel with more testing and analysis by Kees Schoenmakers
as follows:
I ran into an NetMos 9835 serial pci board which behaves a little
different than the standard. This type of expansion board is very common.
"Standard" 8250 compatible devices clear the 'UART_LST_TEMT" bit together
with the "UART_LSR_THRE" bit when writing data to the device.
The NetMos device does it slightly different
I believe that the TEMT bit is coupled to the shift register. The problem
is that after writing data to the device and very quickly after that one
does call serial8250_tx_empty, it returns the wrong information.
My patch makes the test more robust (and solves the problem) and it does
not affect the already correct devices.
Alan:
We may yet need to quirk this but now we know which chips we have a
way to do that should we find this breaks some other 8250 clone with
dodgy THRE.
Signed-off-by: Dick Hollenbeck <dick@softplc.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Kees Schoenmakers <k.schoenmakers@sigmae.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a memory leak by freeing the memory allocated in __class_register
for the class private data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is currently a bug in sysfs_sd_setattr inherited from
sysfs_setattr in 2.6.32 where the first time we set the attributes
on a sysfs file we allocate backing store but do not set the
backing store attributes. Resulting in overly restrictive
permissions on sysfs files.
The fix is to simply modify the code so that it always executes
when we update the sysfs attributes, as we did in 2.6.31 and earlier.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Jean Delvare <khali@linux-fr.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
eem_wrap() is sending a sentinel CRC, but it didn't indicate that to
the host, it should zero bit 14 (bmCRC) in the EEM packet header,
instead of setting it.
Also remove a redundant crc calculation in eem_unwrap().
Signed-off-by: Steve Longerbeam <stevel@netspectrum.com>
Acked-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With CONFIG_USB_ULPI=y, CONFIG_USB<=m, CONFIG_PCI=n and
CONFIG_USB_OTG_UTILS=n, which is the default used for mx31moboard,
the build for all mx3 platforms fails because drivers/usb/otg/ulpi.c
where otg_ulpi_create is defined is not compiled.
Build error:
arch/arm/mach-mx3/built-in.o: In function `mxc_board_init':
kzmarm11.c:(.init.text+0x73c): undefined reference to `otg_ulpi_create'
kzmarm11.c:(.init.text+0x1020): undefined reference to `otg_ulpi_create'
This isn't a strong dependency as drivers/usb/otg/ulpi.c doesn't
use functions defined in drivers/usb/otg/otg.o and is only needed
to get ulpi.o linked into the kernel image.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
g_multi used CONFIG_USB_ETH_RNDIS to check if RNDIS option was requested
where it should check for CONFIG_USB_G_MULTI_RNDIS. As a result, RNDIS
was never present in g_multi regardless of configuration.
This fixes changes made in commit 396cda90d2.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
