This reverts commit 5ed3bc7288.
It turns-out that not all drivers are calling ieee80211_tx_status from a
compatible context. Revert this for now and try again later...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to update the issue_seq on any grant operation, be it via an MDS
reply or a separate grant message. The update in the grant path was
missing. This broke cap release for inodes in which the MDS sent an
explicit grant message that was not soon after followed by a successful
MDS reply on the same inode.
Also fix the signedness on seq locals.
Signed-off-by: Sage Weil <sage@newdream.net>
If an MDS tries to revoke caps that we don't have, we want to send
releases early since they probably contain the caps message the MDS
is looking for.
Previously, we only sent the messages if we didn't have the inode either. But
in a multi-mds system we can retain the inode after dropping all caps for
a single MDS.
Signed-off-by: Greg Farnum <gregf@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
encode_fh on error should update max_len with minimum required
size, so that caller can redo the call with the reallocated buffer.
This is required with open by handle patch series
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Sage Weil <sage@newdream.net>
encode_fh function should return 255 on error as done by other file
system to indicate EOVERFLOW. Also max_len is in sizeof(u32) units
and not in bytes.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Sage Weil <sage@newdream.net>
If we interrupt an osd request, we call __cancel_request, but it wasn't
verifying that req->r_osd was non-NULL before dereferencing it. This could
cause a crash if osds were flapping and we aborted a request on said osd.
Reported-by: Henry C Chang <henry_c_chang@tcloudcomputing.com>
Signed-off-by: Sage Weil <sage@newdream.net>
Fix the IRQ flag handling naming. In linux/irqflags.h under one configuration,
it maps:
local_irq_enable() -> raw_local_irq_enable()
local_irq_disable() -> raw_local_irq_disable()
local_irq_save() -> raw_local_irq_save()
...
and under the other configuration, it maps:
raw_local_irq_enable() -> local_irq_enable()
raw_local_irq_disable() -> local_irq_disable()
raw_local_irq_save() -> local_irq_save()
...
This is quite confusing. There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.
Change this to have the arch provide:
flags = arch_local_save_flags()
flags = arch_local_irq_save()
arch_local_irq_restore(flags)
arch_local_irq_disable()
arch_local_irq_enable()
arch_irqs_disabled_flags(flags)
arch_irqs_disabled()
arch_safe_halt()
Then linux/irqflags.h wraps these to provide:
raw_local_save_flags(flags)
raw_local_irq_save(flags)
raw_local_irq_restore(flags)
raw_local_irq_disable()
raw_local_irq_enable()
raw_irqs_disabled_flags(flags)
raw_irqs_disabled()
raw_safe_halt()
with type checking on the flags 'arguments', and then wraps those to provide:
local_save_flags(flags)
local_irq_save(flags)
local_irq_restore(flags)
local_irq_disable()
local_irq_enable()
irqs_disabled_flags(flags)
irqs_disabled()
safe_halt()
with tracing included if enabled.
The arch functions can now all be inline functions rather than some of them
having to be macros.
Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
Add missing #inclusions of <linux/irq.h> to a whole bunch of files that should
really include it. Note that this can replace #inclusions of <asm/irq.h>.
This is required for the patch to sort out irqflags handling function naming to
compile on MIPS.
The problem is that these files require access to things like setup_irq() -
which isn't available by #including <linux/interrupt.h>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Add missing #inclusion of <linux/irq.h>. Without it, the following error can
occur with the irqflags fixup patches applied:
drivers/net/smc91x.c: In function 'smc_probe':
drivers/net/smc91x.c:1987:2: error: implicit declaration of function 'irq_canonicalize'
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Drop inclusions of asm/system.h from linux/hardirq.h and linux/list.h as
they're no longer required and prevent the M68K arch's IRQ flag handling macros
from being made into inlined functions due to circular dependencies.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add missing consts to the sys_execve() declaration which result in the
following error:
arch/sh/kernel/process_32.c:303: error: conflicting types for 'sys_execve'
/warthog/nfs/linux-2.6-fscache/arch/sh/include/asm/syscalls_32.h:24: error: previous declaration of 'sys_execve' was here
Signed-off-by: David Howells <dhowells@redhat.com>
Rename h/w IRQ flags handling functions to be in line with what is expected for
the irq renaming patch. This renames local_*_hw() to hard_local_*() using the
following perl command:
perl -pi -e 's/local_irq_(restore|enable|disable)_hw/hard_local_irq_\1/ or s/local_irq_save_hw([_a-z]*)[(]flags[)]/flags = hard_local_irq_save\1()/' `find arch/blackfin/ -name "*.[ch]"`
and then fixing up asm/irqflags.h manually.
Additionally, arch/hard_local_save_flags() and arch/hard_local_irq_save() both
return the flags rather than passing it through the argument list.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a missing dependency (mach/blackfin.h) to asm/irqflags.h so that
bfin_read_IMASK() can be used by inline functions.
Signed-off-by: David Howells <dhowells@redhat.com>
Rename the PC2() symbol in the generic DES crypto module to be prefixed with
DES_ to avoid collision with arch code (Blackfin in this case).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Split the BF532 machine type BFIN_*_FIO_FLAG() functions to their own header
file to avoid circular #include problems as these functions require IRQ flag
handling, which requires asm/blackfin.h, which otherwise requires the header
file that defines these functions.
For good measure, also get rid of the inclusion of asm/blackfin.h from
mach/cdefBF532.h (which is circular) and defBF532.h (which is included by
asm/blackfin.h before including this header).
Signed-off-by: David Howells <dhowells@redhat.com>
Split the PLL control code from the Blackfin machine-specific cdef headers so
that the irqflags functions can be renamed without incurring a header loop.
Signed-off-by: David Howells <dhowells@redhat.com>
When we call the slab shrinker to free a page we need to stop at
page count one because the caller always holds a single reference, not zero.
This avoids useless looping over slab shrinkers and freeing too much
memory.
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
The SIGBUS user space signalling is supposed to report the
address granuality of a corruption. Pass this information correctly
for huge pages by querying the hpage order.
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
The original hwpoison code added a new siginfo field si_addr_lsb to
pass the granuality of the fault address to user space. Unfortunately
this field was never copied to user space. Fix this here.
I added explicit checks for the MCEERR codes to avoid having
to patch all potential callers to initialize the field.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
The page-types utility still uses an out of date name for the
unpoison interface: debugfs:hwpoison/renew-pfn
This patch renames and fixes it.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
2.6.36 introduces an API for drivers to switch the IO scheduler
instead of manually calling the elevator exit and init functions.
This API was added since q->elevator must be cleared in between
those two calls. And since we already have this functionality
directly from use by the sysfs interface to switch schedulers
online, it was prudent to reuse it internally too.
But this API needs the queue to be in a fully initialized state
before it is called, or it will attempt to unregister elevator
kobjects before they have been added. This results in an oops
like this:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000051
IP: [<ffffffff8116f15e>] sysfs_create_dir+0x2e/0xc0
PGD 47ddfc067 PUD 47c6a1067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:02.0/0000:04:00.1/irq
CPU 2
Modules linked in: t(+) loop hid_apple usbhid ahci ehci_hcd uhci_hcd libahci usbcore nls_base igb
Pid: 7319, comm: modprobe Not tainted 2.6.36-rc6+ #132 QSSC-S4R/QSSC-S4R
RIP: 0010:[<ffffffff8116f15e>] [<ffffffff8116f15e>] sysfs_create_dir+0x2e/0xc0
RSP: 0018:ffff88027da25d08 EFLAGS: 00010246
RAX: ffff88047c68c528 RBX: 00000000fffffffe RCX: 0000000000000000
RDX: 000000000000002f RSI: 000000000000002f RDI: ffff88047e196c88
RBP: ffff88027da25d38 R08: 0000000000000000 R09: d84156c5635688c0
R10: d84156c5635688c0 R11: 0000000000000000 R12: ffff88047e196c88
R13: 0000000000000000 R14: 0000000000000000 R15: ffff88047c68c528
FS: 00007fcb0b26f6e0(0000) GS:ffff880287400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000051 CR3: 000000047e76e000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process modprobe (pid: 7319, threadinfo ffff88027da24000, task ffff88027d377090)
Stack:
ffff88027da25d58 ffff88047c68c528 00000000fffffffe ffff88047e196c88
<0> ffff88047c68c528 ffff88047e05bd90 ffff88027da25d78 ffffffff8123fb77
<0> ffff88047e05bd90 0000000000000000 ffff88047e196c88 ffff88047c68c528
Call Trace:
[<ffffffff8123fb77>] kobject_add_internal+0xe7/0x1f0
[<ffffffff8123fd98>] kobject_add_varg+0x38/0x60
[<ffffffff8123feb9>] kobject_add+0x69/0x90
[<ffffffff8116efe0>] ? sysfs_remove_dir+0x20/0xa0
[<ffffffff8103d48d>] ? sub_preempt_count+0x9d/0xe0
[<ffffffff8143de20>] ? _raw_spin_unlock+0x30/0x50
[<ffffffff8116efe0>] ? sysfs_remove_dir+0x20/0xa0
[<ffffffff8116eff4>] ? sysfs_remove_dir+0x34/0xa0
[<ffffffff81224204>] elv_register_queue+0x34/0xa0
[<ffffffff81224aad>] elevator_change+0xfd/0x250
[<ffffffffa007e000>] ? t_init+0x0/0x361 [t]
[<ffffffffa007e000>] ? t_init+0x0/0x361 [t]
[<ffffffffa007e0a8>] t_init+0xa8/0x361 [t]
[<ffffffff810001de>] do_one_initcall+0x3e/0x170
[<ffffffff8108c3fd>] sys_init_module+0xbd/0x220
[<ffffffff81002f2b>] system_call_fastpath+0x16/0x1b
Code: e5 41 56 41 55 41 54 49 89 fc 53 48 83 ec 10 48 85 ff 74 52 48 8b 47 18 49 c7 c5 00 46 61 81 48 85 c0 74 04 4c 8b 68 30 45 31 f6 <41> 80 7d 51 00 74 0e 49 8b 44 24 28 4c 89 e7 ff 50 20 49 89 c6
RIP [<ffffffff8116f15e>] sysfs_create_dir+0x2e/0xc0
RSP <ffff88027da25d08>
CR2: 0000000000000051
---[ end trace a6541d3bf07945df ]---
Fix this by adding a registered bit to the elevator queue, which is
set when the sysfs kobjects have been registered.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
since the handle references are all tied to a file_priv, and when it disappears
all the handle refs go with it.
The fbcon ones we'd only notice on unload, but the nouveau notifier one
would would happen on reboot.
nouveau: Reported-by: Marc Dionne <marc.c.dionne@gmail.com>
nouveau: Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
i915 unload: Reported-by: Keith Packard <keithp@keithp.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When marking an inode reclaimable, a per-AG counter is increased, the
inode is tagged reclaimable in its per-AG tree, and, when this is the
first reclaimable inode in the AG, the AG entry in the per-mount tree
is also tagged.
When an inode is finally reclaimed, however, it is only deleted from
the per-AG tree. Neither the counter is decreased, nor is the parent
tree's AG entry untagged properly.
Since the tags in the per-mount tree are not cleared, the inode
shrinker iterates over all AGs that have had reclaimable inodes at one
point in time.
The counters on the other hand signal an increasing amount of slab
objects to reclaim. Since "70e60ce xfs: convert inode shrinker to
per-filesystem context" this is not a real issue anymore because the
shrinker bails out after one iteration.
But the problem was observable on a machine running v2.6.34, where the
reclaimable work increased and each process going into direct reclaim
eventually got stuck on the xfs inode shrinking path, trying to scan
several million objects.
Fix this by properly unwinding the reclaimable-state tracking of an
inode when it is reclaimed.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: stable@kernel.org
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Function read_sb_page may return ERR_PTR(...). Check for it.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NeilBrown <neilb@suse.de>
When performing a resync we pre-allocate some bios and repeatedly use
them. This requires us to re-initialise them each time.
One field (bi_comp_cpu) and some flags weren't being initiaised
reliably.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch adds a per region debugfs file that shows the elapsed time
since the time the o2hb timer was last armed.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
This patch creates debugfs directory for each o2hb region and creates
files to expose the region number and the per region live node bitmap.
This information will be useful in debugging cluster issues.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
This patch prints the bitmaps of live, quorum and failed regions. This
information will be useful in debugging cluster issues.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
In global heartbeat mode, we track the bitmap of regions that have seen
heartbeat timeouts. We fence if the number of such regions is greater than
or equal to half the number of quorum regions.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
o2hb allows online adding of regions. However, a newly added region is not
used in quorum calculations unless it has been added on all nodes. This patch
tracks a bitmap of such quorum regions.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
In global heartbeat mode, we have a upper limit for the number of active regions.
This patch adds the facility to track the number of active global heartbeat
regions and fails to start heartbeat if the number exceeds the maximum.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Currently we track a global livenode bitmap that keeps track of all nodes
that are heartbeating in all regions.
This patch adds the ability to track the livenode bitmap on a per region basis.
We will use this facility in a later patch to allow us to withstand the loss of
a minority number of regions.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
o2hb currently checks slots for configured nodes only. This patch makes
it check the slots for the live nodes too to take care of a race in which
a node is removed from the configuration but not from the live map.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Prints messages when the user adds or removes heartbeat regions in global
heartbeat mode. These messages are useful when debugging cluster related issues.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Adds new dlm message DLM_QUERY_NODEINFO that sends the attributes of all
registered nodes. This message is sent if the negotiated dlm protocol is
1.1 or higher. If the information of the joining node does not match
that of any existing nodes, the join domain request is rejected.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
In global heartbeat mode, the heartbeat is started by the user. This patch
prints an error if the user attempts to mount a volume without starting the
heartbeat.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Adds new dlm message DLM_QUERY_REGION that sends the names of all active
heartbeat regions. This message is only sent in the global heartbeat
mode. If the regions in the joining node do not fully match the ones in
the active nodes, the join domain request is rejected.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Export function in o2hb to get a list of heartbeat regions. It also adds an
upper limit to the length of the heartbeat region name.
o2hb_global_heartbeat_active() currently disables global heartbeat. It will
be enabled in a later patch after all the code is added.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Adds support for heartbeat=global mount option. It ensures that the heartbeat
mode passed matches the one enabled on disk.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
OCFS2_FEATURE_INCOMPAT_CLUSTERINFO allows us to use sb->s_cluster_info for
both userspace and o2cb cluster stacks. It also allows us to extend cluster
info to include stack flags.
This patch also adds stackflags to sb->s_clusterinfo. It also introduces a
clusterinfo flag OCFS2_CLUSTER_O2CB_GLOBAL_HEARTBEAT to denote the enabled
global heartbeat mode.
This incompat flag can be set/cleared using tunefs.ocfs2 --fs-features. The
clusterinfo flag is set/cleared using tunefs.ocfs2 --update-cluster-stack.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
