* 'sched-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix fallback sched_clock()'s offset when using jiffies
* 'core-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: increase MAX_LOCKDEP_ENTRIES and MAX_LOCKDEP_CHAINS
Remove the __initdata annotation for the clock lookups, since they
will be needed when loading modules which use clk_get().
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the __initdata annotation for the clock lookups, since they
will be needed when loading modules which use clk_get().
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Append prompt in /debug/tracing/README file
x86/function-graph: fix constraint for recording old return value
Commit c45d6320 ("fix reference counting of ftdi_private") stopped
ftdi_sio_port_remove() from directly freeing the port-private data, with
the intention if the port was still open, it would be freed when
ftdi_close() is eventually called and releases the last refcount on the
structure.
That's all very well, but ftdi_sio_port_remove() still contains a call
to usb_set_serial_port_data(port, NULL) -- so by the time we get to
ftdi_close() for the port which was unplugged, it _still_ oopses on
dereferencing that NULL pointer, as it did before (and does in 2.6.29).
The fix is just not to clear the private data in ftdi_sio_port_remove().
Then the refcount is properly reduced to zero when the final kref_put()
happens in ftdi_close().
Remove a bogus comment too, while we're at it. And stop doing things
inside "if (priv)" -- it must _always_ be there.
Based loosely on an earlier patch by Daniel Mack, and suggestions by
Alan Stern.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5b7f3a50 (fix dataflash 64-bit divisions) unfortunately
introduced a typo. Erase addr and len were swapped in the pageaddr
calculation, causing the wrong sectors to get erased.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
`local_add_unless(x, y, z)' will be expanded to `(&(x)->y, (y), (x))', but
`&(x)->y' should be `&(x)->a'
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently spitz_ohci_init() that requests GPIO doesn't have
corresponding spitz_ohci_exit() which will gpio_free(). This causes
minor problems e.g. during resume when the OHCI device can't be resumed.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
'mach-pxa' platforms currently rely on a bootloader to setup GPIO pins
and clear RDH (to enable inputs).
A kernel loaded by a 'minimal' bootloader, that doesn't touch any pins,
will not function correctly; inputs will remain disabled, even after the
pins are configured. The following change fixes the issue and has been
verified on Gumstix Verdex XL6P and a custom PXA270 platform.
Signed-off-by: Timothy Clacy <tcl@phaseone.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
I want to reuse tosa/spitz gpio_reset code, but my board needs the reset
gpio to be driven high during normal operation.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add support for SG_IO passthru to virtio_blk. We add the scsi command
block after the normal outhdr, and the scsi inhdr with full status
information aswell as the sense buffer before the regular inhdr.
[hch: forward ported, added the VIRTIO_BLK_F_SCSI flags, some comments
and tested the whole beast]
[axboe: updated to use ->resid and not dual-path the byte count]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (+ checkpatch.pl tweak)
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
request->rq_disk is only set for FS requests or BLOCK_PC requests
originating from the generic block layer scsi ioctls. It's not set
for requests origination from other soures or internal cache flush
commands implemented by the patch I'll send after this.
So instead of using it to get at the private data in do_virtblk_request
setup queue->queuedata and use it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pfn_valid() is meant to be able to tell if a given PFN has valid memmap
associated with it or not. In FLATMEM, it is expected that holes always
have valid memmap as long as there is valid PFNs either side of the hole.
In SPARSEMEM, it is assumed that a valid section has a memmap for the
entire section.
However, ARM and maybe other embedded architectures in the future free
memmap backing holes to save memory on the assumption the memmap is never
used. The page_zone linkages are then broken even though pfn_valid()
returns true. A walker of the full memmap must then do this additional
check to ensure the memmap they are looking at is sane by making sure the
zone and PFN linkages are still valid. This is expensive, but walkers of
the full memmap are extremely rare.
This was caught before for FLATMEM and hacked around but it hits again for
SPARSEMEM because the page_zone linkages can look ok where the PFN linkages
are totally screwed. This looks like a hatchet job but the reality is that
any clean solution would end up consumning all the memory saved by punching
these unexpected holes in the memmap. For example, we tried marking the
memmap within the section invalid but the section size exceeds the size of
the hole in most cases so pfn_valid() starts returning false where valid
memmap exists. Shrinking the size of the section would increase memory
consumption offsetting the gains.
This patch identifies when an architecture is punching unexpected holes
in the memmap that the memory model cannot automatically detect and sets
ARCH_HAS_HOLES_MEMORYMODEL. At the moment, this is restricted to EP93xx
which is the model sub-architecture this has been reported on but may expand
later. When set, walkers of the full memmap must call memmap_valid_within()
for each PFN and passing in what it expects the page and zone to be for
that PFN. If it finds the linkages to be broken, it assumes the memmap is
invalid for that PFN.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Liam Girdwood <lrg@slimlogic.co.uk>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Eric Miao <eric.miao@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
return zero should be correct, so fix it.
[ Impact: eliminate incorrect syslog message ]
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: rostedt@goodmis.org
LKML-Reference: <1242545498-7285-1-git-send-email-tom.leiming@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We have to set up the LVT entry only at counter init time, not at
every switch-in time.
There's friction between NMI and non-NMI use here - we'll probably
remove the per counter configurability of it - but until then, dont
slow down things ...
[ Impact: micro-optimization ]
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Srivatsa Vaddagiri <vatsa@in.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Len expressed concern that the update_mptable feature has
side-effects on the ACPI code.
Make it sure explicitly that the code only ever gets called if
the (default disabled) update_mptable boot quirk option is
disabled.
[ Impact: isolate the update_mptable feature from ACPI code more ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A0DC832.5090200@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To get all device irq routing and to save them.
This is basically an implicit pci=routeirq enablement if (and on if)
the update_mptable boot option (which is off by default) has been
specified.
[ Impact: extend the update_mptable boot opion's scope ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <4A0DB7B4.4060702@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jack found a boot crash on a system which doesn't have memory on node0.
It turns out with recent per_cpu changes, node_number for BSP will always
be 0, and it is not consistent to cpu_to_node() that might set it to a
different (nearer) node already.
aka when numa_set_node() for node0 is called early before per_cpu area is
setup:
two places touched that per_cpu(node_number,):
1. in cpu/common.c::cpu_init() and it is not for BP
| #ifdef CONFIG_NUMA
| if (cpu != 0 && percpu_read(node_number) == 0 &&
| cpu_to_node(cpu) != NUMA_NO_NODE)
| percpu_write(node_number, cpu_to_node(cpu));
| #endif
for BP: traps_init ==> cpu_init
for AP: start_secondary ==> cpu_init
2. cpu/intel.c or amd.c::srat_detect_node via numa_set_node()
for BP: check_bugs ==> identify_boot_cpu ==> identify_cpu()
that is rather later before numa_node_id() is used for BP...
for AP: start_secondary => smp_callin => smp_store_cpu_info() =>
=> identify_secondary_cpu => identify_cpu()
so try to set that for BP earlier in setup_per_cpu_areas(), and
don't bother to set that for APs there (it will be updated later
and will be used later)
(and don't mess the 0 before the copying BP per_cpu data to APs)
[ Impact: fix boot crash on memoryless node-0 ]
Reported-and-tested-by: Jack Steiner <steiner@sgi.com>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4A0C4A02.7050401@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Recently there were some changes to the meaning of node_possible_map,
and it is quite strange:
- the node without memory would be set in node_possible_map
- but some node with less NODE_MIN_SIZE will be kicked out of node_possible_map.
fix it by adding strict_setup_node_bootmem().
Also, remove unparse_node().
so result will be:
1. cpu_to_node() will return online node only (nearest one)
2. apicid_to_node() still returns the node that could be not online but is set
in node_possible_map.
3. node_possible_map will include nodes that mem on it are less NODE_MIN_SIZE
v2: after move_cpus_to_node change.
[ Impact: get node_possible_map right ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <4A0C49BE.6080800@kernel.org>
[ v3: various small cleanups and comment clarifications ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
after:
| commit b263295dbf
| Author: Christoph Lameter <clameter@sgi.com>
| Date: Wed Jan 30 13:30:47 2008 +0100
|
| x86: 64-bit, make sparsemem vmemmap the only memory model
we don't have MEMORY_HOTPLUG_RESERVE anymore.
Historically, x86-64 had an architecture-specific method for memory hotplug
whereby it scanned the SRAT for physical memory ranges that could be
potentially used for memory hot-add later. By reserving those ranges
without physical memory, the memmap would be allocated and left dormant
until needed. This depended on the DISCONTIG memory model which has been
removed so the code implementing HOTPLUG_RESERVE is now dead.
This patch removes the dead code used by MEMORY_HOTPLUG_RESERVE.
(Changelog authored by Mel.)
v2: updated changelog, and remove hotadd= in doc
[ Impact: remove dead code ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Reviewed-by: Mel Gorman <mel@csn.ul.ie>
Workflow-found-OK-by: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A0C4910.7090508@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge reason: sync up to -rc6 which has changes to mm/ which we are
going to touch in the commits to follow as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
should not call that if apic is disabled.
[ Impact: fix crash on certain UP configs ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
LKML-Reference: <4A09CCBB.2000306@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
according to Ingo, io_apic irq-setup related functions have too many
parameters with a repetitive signature.
So reduce related funcs to get less params by passing a pointer
to a newly defined io_apic_irq_attr structure.
v2: io_apic_irq ==> irq_attr
triggering ==> trigger
v3: add set_io_apic_irq_attr
[ Impact: cleanup ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Len Brown <lenb@kernel.org>
LKML-Reference: <4A08ACD3.2070401@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 9e35ad38 ("perf_counter: Rework the perf counter
disable/enable") added code to the powerpc hw_perf_enable (renamed
from hw_perf_restore) to test cpuhw->disabled and return immediately
if it is not set (i.e. if the PMU is already enabled).
Unfortunately the test got added before cpuhw was initialized,
resulting in an oops the first time hw_perf_enable got called.
This fixes it by moving the initialization of cpuhw to before
cpuhw->disabled is tested.
[ Impact: fix oops-causing bug on powerpc ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <18960.56772.869734.304631@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I don't think anything guarantees that the objects in data.page_aligned
are a multiple of PAGE_SIZE, thus the section may end on any boundary.
So the following section, .data.cacheline_aligned needs an explicit
alignment.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Refresh and set these options:
CONFIG_SYSFS_DEPRECATED_V2: y -> n
CONFIG_INPUT_JOYSTICK: y -> n
CONFIG_HID_SONY: n -> m
CONFIG_RTC_DRV_PS3: - -> m
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After upgrading my distcc boxes from gcc 4.2.2 to 4.4.0, the function
graph tracer broke. This was discovered on my x86 boxes.
The issue is that gcc used the same register for an output as it did for
an input in an asm statement. I first thought this was a bug in gcc and
reported it. I was notified that gcc was correct and that the output had
to be flagged as an "early clobber".
I noticed that powerpc had the same issue and this patch fixes it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when #DEBUG
is not defined. That's not really desirable in the ftrace code
which we want to be snappy.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
3334 672 4 4010 faa arch/powerpc/kernel/ftrace.o
size after:
text data bss dec hex filename
2616 360 4 2980 ba4 arch/powerpc/kernel/ftrace.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
FIFO1_DMA_ERR is set twice, the second should be FIFO2_DMA_ERR.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Ram Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 2.6.29, PPC no more admits passing NULL to the dev parameter of
the DMA API. The result is a BUG followed by solid lock-up when the
mv643xx_eth driver brings an interface up. The following patch makes
the driver work on my Pegasos again; it is mostly a search and replace
of NULL by mp->dev->dev.parent in dma allocation/freeing/mapping/unmapping
functions.
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the purposes of bonding is to allow for redundant links, and failover
correctly if the cable is pulled. If all the members of a bonded device have
no carrier present, the bonded device itself needs to report no carrier present
to user space so management tools (like routing daemons) can respond.
Bonding in 802.3ad mode does not work correctly for this because it incorrectly
chooses a link that is down as a possible aggregator.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bridge is configured with no STP and forwarding delay of 0 (which
is typical for virtualization) then when link starts it will flood all
packets for the first 20 seconds.
This bug was introduced by a combination of earlier changes:
* forwarding database uses hold time of zero to indicate
user wants to always flood packets
* optimzation of the case of forwarding delay of 0 avoids the initial
timer tick
The fix is to just skip all the topology change detection code if
kernel STP is not being used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bridge catches all STP packets; even if STP is turned
off. This prevents other systems (which do have STP turned on)
from being able to detect loops in the network.
With this patch, if STP is off, then any packet sent to the STP
multicast group address is forwarded to all ports.
Based on earlier patch by Joakim Tjernlund with changes
to go through forwarding (not local chain), and optimization
that only last octet needs to be checked.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Napi structures are being created each time we open a port, but when
the port is closed the napi structure is only disabled but not removed.
This bug caused hang while removing the driver.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
