Previously, post-softreset readiness is waited as follows.
1. ata_sff_wait_after_reset() waits for 150ms and then for
ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.
2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff.
If not, continue to #3.
3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending
on devmask using ata_sff_wait_ready().
And for post-hardreset readiness,
1. ata_sff_wait_after_reset() waits for 150ms and then for
ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.
2. sata_sff_hardreset waits for device readiness using
ata_sff_wait_ready().
This patch merges and unifies post-reset readiness waits into
ata_sff_wait_ready() and ata_sff_wait_after_reset().
ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready(). If TF
status is 0xff, link status is unknown and the port is SATA, it will
continue polling till ATA_TMOUT_FF_WAIT.
ata_sff_wait_after_reset() is updated to perform the following steps.
1. waits for 150ms.
2. waits for dev0 readiness using ata_sff_wait_ready(). Note that
this is done regardless of devmask, as ata_sff_wait_ready() handles
0xff status correctly, this preserves the original behavior except
that it may wait longer after softreset if link is online but
status is 0xff. This behavior change is very unlikely to cause any
actual difference and is intended. It brings softreset behavior to
that of hardreset.
3. waits for dev1 readiness just the same way ata_bus_post_reset() did.
Now both soft and hard resets call ata_sff_wait_after_reset() after
reset to wait for readiness after resets. As
ata_sff_wait_after_reset() contains calls to ->sff_dev_select(),
explicit call near the end of sata_sff_hardreset() is removed.
This change makes reset implementation simpler and more consistent.
While at it, make the magical 150ms wait post-reset wait duration a
constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take
@link instead of @ap. This is to make them consistent with other
reset helpers and ease core changes.
pata_scc is updated accordingly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Separate out generic ATA portion from ata_sff_postreset() into
ata_std_postreset() and implement ata_sff_postreset() using the std
version.
ata_base_port_ops now has ata_std_postreset() for its postreset and
ata_sff_port_ops overrides it to ata_sff_postreset().
This change affects pdc_adma, ahci, sata_fsl and sata_sil24. pdc_adma
now specifies postreset to ata_sff_postreset() explicitly. sata_fsl
and sata_sil24 now use ata_std_postreset() which makes no difference
to them. ahci now calls ata_std_postreset() from its own postreset
method, which causes no behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Separate out generic ATA portion from ata_sff_prereset() into
ata_std_prereset() and implement ata_sff_prereset() using the std
version. Waiting for device readiness is the only SFF specific part.
ata_base_port_ops now has ata_std_prereset() for its prereset and
ata_sff_port_ops overrides it to ata_sff_prereset(). This change can
affect pdc_adma, ahci, sata_fsl and sata_sil24. pdc_adma implements
its own prereset using ata_sff_prereset() and the rest has hardreset
and thus are unaffected by this change.
This change reflects real world situation. There is no generic way to
wait for device readiness for non-SFF controllers and some of them
don't have any mechanism for that. Non-sff drivers which don't have
hardreset should wrap ata_std_prereset() and wait for device readiness
itself but there's no such driver now and isn't likely to be popular
in the future either.
Signed-off-by: Tejun Heo <htejun@gmail.com>
->sff_irq_clear() is called only from SFF interrupt handler, so there
is no reason to initialize it for non-SFF controllers. Also,
ata_sff_irq_clear() can handle both BMDMA and non-BMDMA SFF
controllers.
This patch kills ata_noop_irq_clear() and removes it from base
port_ops and sets ->sff_irq_clear to ata_sff_irq_clear() in sff
port_ops instead of bmdma port_ops.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Add sff_ prefix to SFF specific port ops.
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames ops and doesn't introduce any
behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
SFF functions have confusing names. Some have sff prefix, some have
bmdma, some std, some pci and some none. Unify the naming by...
* SFF functions which are common to both BMDMA and non-BMDMA are
prefixed with ata_sff_.
* SFF functions which are specific to BMDMA are prefixed with
ata_bmdma_.
* SFF functions which are specific to PCI but apply to both BMDMA and
non-BMDMA are prefixed with ata_pci_sff_.
* SFF functions which are specific to PCI and BMDMA are prefixed with
ata_pci_bmdma_.
* Drop generic prefixes from LLD specific routines. For example,
bfin_std_dev_select -> bfin_dev_select.
The following renames are noteworthy.
ata_qc_issue_prot() -> ata_sff_qc_issue()
ata_pci_default_filter() -> ata_bmdma_mode_filter()
ata_dev_try_classify() -> ata_sff_dev_classify()
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames functions and doesn't
introduce any behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Currently whether a command should be retried after failure is
determined inside ata_eh_finish(). Add ATA_QCFLAG_RETRY and move the
logic into ata_eh_autopsy(). This makes things clearer and helps
extending retry determination logic.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_chk_status() just calls ops->check_status and it only adds
confusion with other status functions. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_pci_default_filter() doesn't really have anything to do with PCI.
It's generally applicable to BMDMA controllers. Move it out of
CONFIG_PCI.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Move SFF related functions from libata-core.c to libata-sff.c.
ata_[bmdma_]sff_port_ops, ata_devchk(), ata_dev_try_classify(),
ata_std_dev_select(), ata_tf_to_host(), ata_busy_sleep(),
ata_wait_after_reset(), ata_wait_ready(), ata_bus_post_reset(),
ata_bus_softreset(), ata_bus_reset(), ata_std_softreset(),
sata_std_hardreset(), ata_fill_sg(), ata_fill_sg_dumb(),
ata_qc_prep(), ata_dump_qc_prep(), ata_data_xfer(),
ata_data_xfer_noirq(), ata_pio_sector(), ata_pio_sectors(),
atapi_send_cdb(), __atapi_pio_bytes(), atapi_pio_bytes(),
ata_hsm_ok_in_wq(), ata_hsm_qc_complete(), ata_hsm_move(),
ata_pio_task(), ata_qc_issue_prot(), ata_host_intr(),
ata_interrupt(), ata_std_ports()
* Make ata_pio_queue_task() global as it's now called from
libata-sff.c.
* Move SFF related stuff in include/linux/libata.h and
drivers/ata/libata.h into one place. While at it, move timing
constants into the global enum definition and fortify comments a
bit.
This patch strictly moves stuff around and as such doesn't cause any
functional difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently reset methods are not specified directly in the
ata_port_operations table. If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods. It's done this way for two reasons.
First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.
Second, as ->error_handler uses those reset methods, it can get
confusing. ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.
Now that ops table uses inheritance, the first problem doesn't exist
anymore. The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks. In fact, there currently is no driver which actually
modifies error handling behavior. Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH. I don't think making ops layering strict has
any noticeable benefit.
This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops. Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.
* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
aren't accessible. sata_promise doesn't need to use separate
error_handlers for PATA and SATA anymore.
* softreset is broken for sata_inic162x and sata_sx4. As libata now
always prefers hardreset, this doesn't really matter but the ops are
forced to NULL using ATA_OP_NULL for documentation purpose.
* pata_hpt374 needs to use different prereset for the first and second
PCI functions. This used to be done by branching from
hpt374_error_handler(). The proper way to do this is to use
separate ops and port_info tables for each function. Converted.
Signed-off-by: Tejun Heo <htejun@gmail.com>
libata core layer doesn't care about sht or ->irq_handler. Those are
only of interest to the LLD during initialization. This is confusing
and has caused several drivers to have duplicate unused initializers
for these fields.
Currently only sata_nv uses these fields. Make sata_nv use
->private_data, which is supposed to carry LLD-specific information,
instead and kill ->sht and ->irq_handler. nv_pi_priv structure is
defined and struct literals are used to initialize private_data.
Notational overhead is negligible.
Signed-off-by: Tejun Heo <htejun@gmail.com>
port_info->private_data is currently used for two purposes - to record
private data about the port_info or to specify host->private_data to
use when allocating ata_host.
This overloading is confusing and counter-intuitive in that
port_info->private_data becomes host->private_data instead of
port->private_data. In addition, port_info and host don't correspond
to each other 1-to-1. Currently, the first non-NULL
port_info->private_data is used.
This patch makes port_info->private_data just be what it is -
private_data for the port_info where LLD can jot down extra info.
libata no longer sets host->private_data to the first non-NULL
port_info->private_data, @host_priv argument is added to
ata_pci_init_one() instead. LLDs which use ata_pci_init_one() can use
this argument to pass in pointer to host private data. LLDs which
don't should use init-register model anyway and can initialize
host->private_data directly.
Adding @host_priv instead of using init-register model for LLDs which
use ata_pci_init_one() is suggested by Alan Cox.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
ata_pci_init_one() is the only function which uses ops->irq_handler
and pi->sht. Other initialization functions take the same information
as arguments. This causes confusion and duplicate unused entries in
structures.
Make ata_pci_init_one() take sht as an argument and use ata_interrupt
implicitly. All current users use ata_interrupt and if different irq
handler is necessary open coding ata_pci_init_one() using
ata_prepare_sff_host() and ata_activate_sff_host can be done under ten
lines including error handling and driver which requires custom
interrupt handler is likely to require custom initialization anyway.
As ata_pci_init_one() was the last user of ops->irq_handler, this
patch also kills the field.
Signed-off-by: Tejun Heo <htejun@gmail.com>
libata lets low level drivers build ata_port_operations table and
register it with libata core layer. This allows low level drivers
high level of flexibility but also burdens them with lots of
boilerplate entries.
This becomes worse for drivers which support related similar
controllers which differ slightly. They share most of the operations
except for a few. However, the driver still needs to list all
operations for each variant. This results in large number of
duplicate entries, which is not only inefficient but also error-prone
as it becomes very difficult to tell what the actual differences are.
This duplicate boilerplates all over the low level drivers also make
updating the core layer exteremely difficult and error-prone. When
compounded with multi-branched development model, it ends up
accumulating inconsistencies over time. Some of those inconsistencies
cause immediate problems and fixed. Others just remain there dormant
making maintenance increasingly difficult.
To rectify the problem, this patch implements ata_port_operations
inheritance. To allow LLDs to easily re-use their own ops tables
overriding only specific methods, this patch implements poor man's
class inheritance. An ops table has ->inherits field which can be set
to any ops table as long as it doesn't create a loop. When the host
is started, the inheritance chain is followed and any operation which
isn't specified is taken from the nearest ancestor which has it
specified. This operation is called finalization and done only once
per an ops table and the LLD doesn't have to do anything special about
it other than making the ops table non-const such that libata can
update it.
libata provides four base ops tables lower drivers can inherit from -
base, sata, pmp, sff and bmdma. To avoid overriding these ops
accidentaly, these ops are declared const and LLDs should always
inherit these instead of using them directly.
After finalization, all the ops table are identical before and after
the patch except for setting .irq_handler to ata_interrupt in drivers
which didn't use to. The .irq_handler doesn't have any actual effect
and the field will soon be removed by later patch.
* sata_sx4 is still using old style EH and currently doesn't take
advantage of ops inheritance.
Signed-off-by: Tejun Heo <htejun@gmail.com>
libata lets low level drivers build scsi_host_template and register it
to the SCSI layer. This allows low level drivers high level of
flexibility but also burdens them with lots of boilerplate entries.
This patch implements SHT initializers which can be used to initialize
all the boilerplate entries in a sht. Three variants of them are
implemented - BASE, BMDMA and NCQ - for different types of drivers.
Note that entries can be overriden by putting individual initializers
after the helper macro.
All sht tables are identical before and after this patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
->irq_clear() is used to clear IRQ bit of a SFF controller and isn't
useful for drivers which don't use libata SFF HSM implementation.
However, it's a required callback and many drivers implement their own
noop version as placeholder. This patch implements ata_noop_irq_clear
and use it to replace those custom placeholders.
Also, SFF drivers which don't support BMDMA don't need to use
ata_bmdma_irq_clear(). It becomes noop if BMDMA address isn't
initialized. Convert them to use ata_noop_irq_clear().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Over the time, ops in ata_port_operations has become a bit confusing.
Reorganize. SFF/BMDMA ops are separated into separate a group as they
will be taken out of ata_port_operations later.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_ehi_schedule_probe() was created to hide details of link-resuming
reset magic. Now that all the softreset workarounds are gone,
scheduling probe is very simple - set probe_mask and request RESET.
Kill ata_ehi_schedule_probe() and open code it. This also increases
consistency as ata_ehi_schedule_probe() couldn't cover individual
device probings so they were open-coded even when the helper existed.
While at it, define ATA_ALL_DEVICES as mask of all possible devices on
a link and always use it when requesting probe on link level for
simplicity and consistency. Setting extra bits in the probe_mask
doesn't hurt anybody.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Some controllers can't reliably record the initial D2H FIS after SATA
link is brought online for whatever reason. Advanced controllers
which don't have traditional TF register based interface often have
this problem as they don't really have the TF registers to update
while the controller and link are being initialized.
SKIP_D2H_BSY works around the problem by skipping the wait for device
readiness before issuing SRST, so for such controllers libata issues
SRST blindly and hopes for the best.
Now that libata defaults to hardreset, this workaround is no longer
necessary. For controllers which have support for hardreset, SRST is
never issued by itself. It is only issued as follow-up SRST for
device classification and PMP initialization, so there's no need to
wait for it from prereset.
Kill ATA_LFLAG_SKIP_D2H_BSY.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ATA_EHI_RESUME_LINK has two functions - promote reset to hardreset if
ATA_LFLAG_HRST_TO_RESUME is set and preventing EH from shortcutting
reset action when probing is requested. The former is gone now and
the latter can easily be achieved by making EH to perform at least one
reset if reset is requested, which also makes more sense than
depending on RESUME_LINK flag.
As ATA_EHI_RESUME_LINK was the only EHI reset modifier, this also
kills reset modifier handling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that hardreset is the preferred method of resetting, there's no
need for ATA_LFLAG_HRST_TO_RESUME flag. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
When both soft and hard resets are available, libata preferred
softreset till now. The logic behind it was to be softer to devices;
however, this doesn't really help much. Rationales for the change:
* BIOS may freeze lock certain things during boot and softreset can't
unlock those. This by itself is okay but during operation PHY event
or other error conditions can trigger hardreset and the device may
end up with different configuration.
For example, after a hardreset, previously unlockable HPA can be
unlocked resulting in different device size and thus revalidation
failure. Similar condition can occur during or after resume.
* Certain ATAPI devices require hardreset to recover after certain
error conditions. On PATA, this is done by issuing the DEVICE RESET
command. On SATA, COMRESET has equivalent effect. The problem is
that DEVICE RESET needs its own execution protocol.
For SFF controllers with bare TF access, it can be easily
implemented but more advanced controllers (e.g. ahci and sata_sil24)
require specialized implementations. Simply using hardreset solves
the problem nicely.
* COMRESET initialization sequence is the norm in SATA land and many
SATA devices don't work properly if only SRST is used. For example,
some PMPs behave this way and libata works around by always issuing
hardreset if the host supports PMP.
Like the above example, libata has developed a number of mechanisms
aiming to promote softreset to hardreset if softreset is not going
to work. This approach is time consuming and error prone.
Also, note that, dependingon how you read the specs, it could be
argued that PMP fan-out ports require COMRESET to start operation.
In fact, all the PMPs on the market except one don't work properly
if COMRESET is not issued to fan-out ports after PMP reset.
* COMRESET is an integral part of SATA connection and any working
device should be able to handle COMRESET properly. After all, it's
the way to signal hardreset during reboot. This is the most used
and recommended (at least by the ahci spec) method of resetting
devices.
So, this patch makes libata prefer hardreset over softreset by making
the following changes.
* Rename ATA_EH_RESET_MASK to ATA_EH_RESET and use it whereever
ATA_EH_{SOFT|HARD}RESET used to be used. ATA_EH_{SOFT|HARD}RESET is
now only used to tell prereset whether soft or hard reset will be
issued.
* Strip out now unneeded promote-to-hardreset logics from
ata_eh_reset(), ata_std_prereset(), sata_pmp_std_prereset() and
other places.
Signed-off-by: Tejun Heo <htejun@gmail.com>
We were already doing what amounts to a get_phy_id from within
get_phy_device, and rather than duplicate this for the TBIPA
probing, we might as well just factor it out and make it available
instead.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In order to not trip the clocksource watchdog, kgdb must touch the
clocksource watchdog on the return to normal system run state.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
polled console handling support, to access a console in an irq-less
way while in debug or irq context.
absolutely zero impact as long as CONFIG_CONSOLE_POLL is disabled.
(which is the default)
[ jan.kiszka@siemens.com: lots of cleanups ]
[ mingo@elte.hu: redesign, splitups, cleanups. ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
kgdb core code. Handles the protocol and the arch details.
[ mingo@elte.hu: heavily modified, simplified and cleaned up. ]
[ xemul@openvz.org: use find_task_by_pid_ns ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
add probe_kernel_read() and probe_kernel_write().
Uninlined and restricted to kernel range memory only, as suggested
by Linus.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Move documentation from semaphore.h to semaphore.c as requested by
Andrew Morton. Also reformat to kernel-doc style and add some more
notes about the implementation.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
By removing the negative values of 'count' and relying on the wait_list to
indicate whether we have any waiters, we can simplify the implementation
by removing the protection against an unlikely race condition. Thanks to
David Howells for his suggestions.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
ACPI currently emulates a timeout for semaphores with calls to
down_trylock and sleep. This produces horrible behaviour in terms of
fairness and excessive wakeups. Now that we have a unified semaphore
implementation, adding a real down_trylock is almost trivial.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Semaphores are no longer performance-critical, so a generic C
implementation is better for maintainability, debuggability and
extensibility. Thanks to Peter Zijlstra for fixing the lockdep
warning. Thanks to Harvey Harrison for pointing out that the
unlikely() was unnecessary.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
quota.h currently relies on asm/semaphore.h (through some chain; it
doesn't actually include semaphore.h itself) to include wait.h. As
well as being bad practice to rely on an implicit include, subsequent
patches will break this. While I'm in this file, add atomic.h and
list.h, and sort the list of includes.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
include/linux/ext4_fs_i.h is included in include/linux/ext_fs.h twice
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
I checked ext4_ioctl and it looked largely safe to not be used
without BKL. So convert it over to unlocked_ioctl.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Fail migrate if we allocated new blocks via mmap write.
If we write to holes in the file via mmap, we end up allocating
new blocks. This block allocation happens without taking inode->i_mutex.
Since migrate is protected by i_mutex and migrate expects that no
new blocks get allocated during migrate, fail migrate if new blocks
get allocated.
We can't take inode->i_mutex in the mmap write path because that
would result in a locking order violation between i_mutex and mmap_sem.
Also adding a separate rw_sempahore for protection is really high overhead
for a rare operation such as migrate.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] linux/libata.h: reorganize ata_device struct members a bit
ahci: SB600 ahci can't do MSI, blacklist that capability
libata: More TSSTcorp pain, keep in sync with legacy IDE
pata_via: Fix 6410 misdetect
[libata] pata_atiixp: fix PIO timing data misprogramming
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Convert most new-style drivers to use module aliasing
i2c: Add support for device alias names
i2c-amd756-s4882: Fix an error path
i2c: Drop unused RTC driver IDs
i2c/tps65010: Add missing intialization of client data
i2c-sis5595: Minor cleanups in sis5595_access
i2c-piix4: Minor cleanups
i2c: Spelling fix (successful)
i2c-stub: No newline in parameter description
Put the big stuff at the end, to prepare for upcoming changes (and
also hopefully achieve nicer packing of remaining members).
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Based on earlier work by Jon Smirl and Jochen Friedrich.
This patch allows new-style i2c chip drivers to have alias names using
the official kernel aliasing system and MODULE_DEVICE_TABLE(). At this
point, the old i2c driver binding scheme (driver_name/type) is still
supported.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jochen Friedrich <jochen@scram.de>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
The x1208, pcf8563 and isl1208 RTC drivers have been converted to
new-style i2c drivers, so they no longer use I2C driver IDs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Formatting cleanup
RDMA/nes: Add support for SFP+ PHY
RDMA/nes: Use LRO
IPoIB: Copy child MTU from parent
IB/mthca: Avoid changing userspace ABI to handle DMA write barrier attribute
IB/mthca: Avoid recycling old FMR R_Keys too soon
mlx4_core: Avoid recycling old FMR R_Keys too soon
IB/ehca: Allocate event queue size depending on max number of CQs and QPs
IPoIB: Use separate CQ for UD send completions
IB/iser: Count FMR alignment violations per session
IB/iser: Move high-volume debug output to higher debug level
IB/ehca: handle negative return value from ibmebus_request_irq() properly
RDMA/cxgb3: Support peer-2-peer connection setup
RDMA/cxgb3: Set the max_mr_size device attribute correctly
RDMA/cxgb3: Correctly serialize peer abort path
mlx4_core: Add a way to set the "collapsed" CQ flag
Extend the mlx4_cq_resize() API with a way to set the "collapsed" flag
for the CQ being created.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cast the CAP_*_SET macros to be of kernel_cap_t type to avoid compiler
warnings.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make secctx_to_secid() take constant secdata.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
spin_is_locked() doesn't work on UP without spinlock debugging. Make it
safer and just return 1 on UP, so we don't get false positives. The plan
is to kill this debug function during the -rc cycle.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
