This patch optimizes the timer load and start sequence. By combining the
load and start a needless posted wait can be removed from the system timer
execution path.
* Before patch register writes are taking up .078% @ 500MHz during idle.
Address |total |min |max |avr |count|ratio%
old\process\default_idle|7.369s |0.0us|999.902ms|14.477ms|509. |62.661%
ld\Global\cpu_v7_do_idle|4.265s |0.0us|375.786ms|24.374ms|175. |36.270%
(UNKNOWN)|17.503ms|0.us|531.080us|5.119us|3419. |0.148%
r\omap_dm_timer_set_load|8.135ms|0.0us|79.887us|15.065us|540. |0.069% <--
\vmlinux-old\Global\_end|2.023ms|0.0us|4.000us|0.560us|3613. |0.017%
-old\Global\__raw_readsw|1.962ms|0.0us|108.610us|9.167us|214. |0.016%
old\smc91x\smc_interrupt|1.353ms|0.0us|10.212us|2.348us|576. |0.011%
s/namei\__link_path_walk|1.161ms|0.0us|4.310us|0.762us| 1524. |0.009%
\omap_dm_timer_write_reg|1.085ms|0.0us|126.150us|2.153us|504. |0.009% <--
* After patch timer functions do not show up in top listings for long captures.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the use of write posting for the timer. Previously, every
write could lock the requestor for almost 3x32KHz cycles. This patch only
synchronizes before writes and reads instead of after them and it does
it on per register basis. Doing it this way there is some chance to hide
some of the sync latency. It also removes some needless reads when
non-posted mode is there. With out this fix the read/writes take almost
2% CPU load @500MHz just waiting on tick timer registers.
Also define new 34xx only registers.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Channel should be marked active only when DMA is really started. Otherwise
just omap_request_dma, omap_dma_link_lch and omap_dma_unlink_lch will cause
incorrect dump_stack().
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GFS2 calls permission() to verify permissions after locks on the files
have been taken.
For this it's sufficient to call gfs2_permission() instead. This
results in the following changes:
- IS_RDONLY() check is not performed
- IS_IMMUTABLE() check is not performed
- devcgroup_inode_permission() is not called
- security_inode_permission() is not called
IS_RDONLY() should be unnecessary anyway, as the per-mount read-only
flag should provide protection against read-only remounts during
operations. do_gfs2_set_flags() has been fixed to perform
mnt_want_write()/mnt_drop_write() to protect against remounting
read-only.
IS_IMMUTABLE has been added to gfs2_permission()
Repeating the security checks seems to be pointless, as they don't
normally change, and if they do, it's independent of the filesystem
state.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
fix this warning:
arch/x86/mm/init_64.c: In function 'early_memtest':
arch/x86/mm/init_64.c:524: warning: passing argument 2 of 'find_e820_area_size' from incompatible pointer type
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Today's linux-next build (powerpc ppc64_defconfig) failed like this:
arch/powerpc/mm/tlb_64.c: In function 'pgtable_free_now':
arch/powerpc/mm/tlb_64.c:66: error: too many arguments to function 'smp_call_function'
arch/powerpc/kernel/machine_kexec_64.c: In function 'kexec_prepare_cpus':
arch/powerpc/kernel/machine_kexec_64.c:175: error: too many arguments to function 'smp_call_function'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: <linuxppc-dev@ozlabs.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andrew Morton reported this against linux-next:
ERROR: ".save_stack_trace" [tests/backtracetest.ko] undefined!
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Update the association of a memory section with a numa node that
occurs during hotplug add of a memory section. This adds a check in
the hot_add_scn_to_nid() routine for the
ibm,dynamic-reconfiguration-memory node in the device tree. If
present the new hot_add_drconf_scn_to_nid() routine is invoked, which
can properly parse the ibm,dynamic-reconfiguration-memory node of the
device tree and make the proper numa node associations.
This also introduces the valid_hot_add_scn() routine as a helper
function for code that is common to the hot_add_scn_to_nid() and
hot_add_drconf_scn_to_nid() routines.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This splits off several pieces of code that parse the
ibm,dynamic-reconfiguration-memory node of the device tree into separate
helper routines. This is in preparation for the next commit that will
use these helper routines. There are no functional changes in this patch.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates the device tree manipulation routines so that memory
add/remove of lmbs represented under the
ibm,dynamic-reconfiguration-memory node of the device tree invokes the
hotplug notifier chain.
This change is needed because of the change in the way memory is
represented under the ibm,dynamic-reconfiguration-memory node. All lmbs
are described in the ibm,dynamic-memory property instead of having a
separate node for each lmb as in previous device tree layouts. This
requires the update_node() routine to check for updates to the
ibm,dynamic-memory property and invoke the hotplug notifier chain.
This also updates the pseries hotplug notifier to be able to gather information
for lmbs represented under the ibm,dynamic-reconfiguration-memory node and
have the lmbs added/removed.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use the base address of the lmb to derive the starting page frame number
instead of trying to extract it from the drc index of the lmb. The drc
index should not be used for this as it will, and did, break.
Until this point, systems that have had memory represented in the device
tree with a node for each lmb the drc index would (luckily) closely
track the base address of the lmb. For example a lmb with a drc index
of 8000000a would have a base address of a0000000. This correlation
allowed the current code to derive the starting page frame number from
the drc inddex
Device tree layouts where lmbs are represented under the
ibm,dynamic-reconfiguration-memory node in the ibm,dynamic-memory
property do not have this correlation between the drc index and base
address of the lmb.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Allow the phandle passed to the /proc/ppc64/ofdt file to be specified
in formats other than decimal. This allows us to easily specify phandle
values in hex that would otherwise appear as negative integers.
This is an issue on systems where the value of
/proc/device-tree/ibm,dynamic-reconfiguration-memory.ibm,phandle is
fffffff9. Having to pass this to the ofdt file as a string results in
a large negative number, and simple_strtoul() does not handle negative
numbers.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since Roland's ptrace cleanup starting with commit
f65255e8d5 ("[POWERPC] Use user_regset
accessors for FP regs"), the dump_task_* functions are no longer being
used.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merges and cleans up some of the ugly copy/to from user code
which is required for the new fpr and vsx layout in the thread_struct.
Also fixes some hard coded buffer sizes and removes a redundant
fpr_flush_to_thread.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To allow for a single kernel image on e500 v1/v2/mc we need to fixup lwsync
at runtime. On e500v1/v2 lwsync causes an illop so we need to patch up
the code. We default to 'sync' since that is always safe and if the cpu
is capable we will replace 'sync' with 'lwsync'.
We introduce CPU_FTR_LWSYNC as a way to determine at runtime if this is
needed. This flag could be moved elsewhere since we dont really use it
for the normal CPU_FTR purpose.
Finally we only store the relative offset in the fixup section to keep it
as small as possible rather than using a full fixup_entry.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to use PPC_LCMPI otherwise we get compile errors like:
arch/powerpc/lib/feature-fixups-test.S: Assembler messages:
arch/powerpc/lib/feature-fixups-test.S:142: Error: Unrecognized opcode: `cmpdi'
arch/powerpc/lib/feature-fixups-test.S:149: Error: Unrecognized opcode: `cmpdi'
arch/powerpc/lib/feature-fixups-test.S:164: Error: Unrecognized opcode: `cmpdi'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we get this warning:
arch/powerpc/kernel/init_task.c:33: warning: missing braces around initializer
arch/powerpc/kernel/init_task.c:33: warning: (near initialization for 'init_task.thread.fpr[0]')
This fixes it.
Noticed by Stephen Rothwell.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the kernel fails to build with the above config options with:
CC arch/powerpc/mm/mem.o
arch/powerpc/mm/mem.c: In function 'arch_add_memory':
arch/powerpc/mm/mem.c:130: error: implicit declaration of function 'create_section_mapping'
This explicitly includes asm/sparsemem.h in arch/powerpc/mm/mem.c and
moves the guards in include/asm-powerpc/sparsemem.h to protect the
SPARSEMEM specific portions only.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fedora reports that mem_init()'s zap_low_mappings(), extended to SMP in
61165d7a03 x86: fix app crashes after SMP
resume causes 32-bit Intel Mac machines to reboot very early when
booting with EFI.
The EFI code appears to manage low mappings for itself when needed; but
like many before it, confuses PSE with PAE. So it has only been mapping
half the space it needed when PSE but not PAE. This remained unnoticed
until we moved the SMP zap_low_mappings() before
efi_enter_virtual_mode(). Presumably could have been noticed years ago
if anyone ran a UP kernel on such machines?
Reported-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Glauber Costa <gcosta@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Peter Jones <pjones@redhat.com>
* 'i2c-fix' of git://aeryn.fluff.org.uk/bjdooks/linux:
I2C: S3C2410: Add MODULE_ALIAS() for s3c2440 device.
I2C: S3C2410: Fixup error codes returned rom a transfer.
I2C: S3C2410: Check ACK on byte transmission
* 'for-2.6.26' of git://git.kernel.dk/linux-2.6-block:
Properly notify block layer of sync writes
block: Fix the starving writes bug in the anticipatory IO scheduler
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (8178): uvc: Fix compilation breakage for the other drivers, if uvc is selected
V4L/DVB (8145a): USB Video Class driver
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5131/1: Annotate platform_secondary_init with trace_hardirqs_off
[ARM] 5117/1: pxafb: fix __devinit/exit annotations
[ARM] Export dma_sync_sg_for_device()
[ARM] 5109/1: Mark rtc sa1100 driver as wakeup source before registering it
[ARM] 5116/1: pxafb: cleanup and fix order of failure handling
[ARM] 5115/1: pxafb: fix ifdef for command line option handling
ARM: OMAP: Correcting the gpmc prefetch control register address
ARM: OMAP: DMA: Don't mark channel active in omap_enable_channel_irq
Not sure how this came to get inverted but it appears to have been my
mess up.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix divide error when trying to configure rt_period to zero
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Fix bad hint about irqs in i2c.h
i2c: Documentation: fix device matching description
* 'for-2.6.26' of git://neil.brown.name/md:
Fix error paths if md_probe fails.
Don't acknowlege that stripe-expand is complete until it really is.
Ensure interrupted recovery completed properly (v1 metadata plus bitmap)
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc/mpc5200: Fix lite5200b suspend/resume
powerpc/legacy_serial: Bail if reg-offset/shift properties are present
powerpc/bootwrapper: update for initrd with simpleImage
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (55 commits)
net: fib_rules: fix error code for unsupported families
netdevice: Fix wrong string handle in kernel command line parsing
net: Tyop of sk_filter() comment
netlink: Unneeded local variable
net-sched: fix filter destruction in atm/hfsc qdisc destruction
net-sched: change tcf_destroy_chain() to clear start of filter list
ipv4: fix sysctl documentation of time related values
mac80211: don't accept WEP keys other than WEP40 and WEP104
hostap: fix sparse warnings
hostap: don't report useless WDS frames by default
textsearch: fix Boyer-Moore text search bug
netfilter: nf_conntrack_tcp: fixing to check the lower bound of valid ACK
ipv6 route: Convert rt6_device_match() to use RT6_LOOKUP_F_xxx flags.
netlabel: Fix a problem when dumping the default IPv6 static labels
net/inet_lro: remove setting skb->ip_summed when not LRO-able
inet fragments: fix race between inet_frag_find and inet_frag_secret_rebuild
CONNECTOR: add a proc entry to list connectors
netlink: Fix some doc comments in net/netlink/attr.c
tcp: /proc/net/tcp rto,ato values not scaled properly (v2)
include/linux/netdevice.h: don't export MAX_HEADER to userspace
...
When scheduled swaps occur, we need to blit between front & back
buffers. If the buffers are tiled, we need to set the appropriate
XY_SRC_COPY tile bit, but only on 965 chips, since it will cause
corruption on pre-965 (e.g. 945).
Bug reported by and fix tested by Tomas Janousek <tomi@nomi.cz>.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 656acd2bbc ("Input: fix locking in
force-feedback core") causes the following regression on m68k:
| linux/drivers/input/ff-core.c: In function 'input_ff_upload':
| linux/drivers/input/ff-core.c:172: error: dereferencing pointer to incomplete type
| linux/drivers/input/ff-core.c: In function 'erase_effect':
| linux/drivers/input/ff-core.c:197: error: dereferencing pointer to incomplete type
| linux/drivers/input/ff-core.c:204: error: dereferencing pointer to incomplete type
| make[4]: *** [drivers/input/ff-core.o] Error 1
As the incomplete type is `struct task_struct', including <linux/sched.h> fixes
it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lock_kernel() calls have been pushed down into code which needs it, so
there is no need to take the BKL at this level anymore.
This work inspired and aided by Andi Kleen's unlocked_fasync() patches.
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
