The fact that an architecture/board has XHCI, OHCI or EHCI does not
depend on the fact that the kernel is configured with USB_SUPPORT.
Make the Kconfig reflect this fact thus avoiding ugly messages like:
warning: (MIPS_ALCHEMY && CAVIUM_OCTEON_REFERENCE_BOARD && SOC_AR71XX && SOC_AR724X && SOC_AR913X && SOC_AR933X) selects USB_ARCH_HAS_EHCI which has unmet direct dependencies (USB_SUPPORT)
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We actually clear LDO_ST_ON_BIT for standby mode in tps65910_set_mode.
Fix the logic in tps65910_get_mode.
Supply state (EEPROM bits):
ST[1:0] = 00 : Off
ST[1:0] = 01 : On high power (ACTIVE)
ST[1:0] = 10 : Off
ST[1:0] = 11 : On low power (SLEEP)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert mx27vis-aic32x4 to platform driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The below patch fixes some typos in drivers/staging/mei/* that I have found while
doing a little bit of reading.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because we don't have vblank hooked up via drm_irq (which is a bit
awkward due to separation between omapdss (which knows the irq #)
and omapdrm, for now use gettimeofday to have a semi-sane timestamp
in the page-flip event. Otherwise apps like weston drm compositor,
which use the timestamp in it's animations, get highly confused.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The endwin irq indicates that DSS has finished scanning out a buffer.
Use this to trigger page-flip event to userspace, so this happens
only *after* the previous buffer is finished.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Multiple video pipes on same output with same z-order is an undefined
behavior. Set a unique z-order value based on overlay number/id.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sh_mmcif call dev_pm_qos_expose_latency_limit() to expose
the PM QoS latency limit to user space and specify the initial
value of it as 100 microseconds.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Make tmio_mmc call dev_pm_qos_expose_latency_limit() to expose
the PM QoS latency limit to user space and specify the initial
value of it as 100 microseconds.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
A runtime suspend of a device (e.g. an MMC controller) belonging to
a power domain or, in a more complicated scenario, a runtime suspend
of another device in the same power domain, may cause power to be
removed from the entire domain. In that case, the amount of time
necessary to runtime-resume the given device (e.g. the MMC
controller) is often substantially greater than the time needed to
run its driver's runtime resume callback. That may hurt performance
in some situations, because user data may need to wait for the
device to become operational, so we should make it possible to
prevent that from happening.
For this reason, introduce a new sysfs attribute for devices,
power/pm_qos_resume_latency_us, allowing user space to specify the
upper bound of the time necessary to bring the (runtime-suspended)
device up after the resume of it has been requested. However, make
that attribute appear only for the devices whose drivers declare
support for it by calling the (new) dev_pm_qos_expose_latency_limit()
helper function with the appropriate initial value of the attribute.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
With the latest and greatest changes to the freezer, I started seeing
panics that were caused by jbd2 running post-process freezing and
hitting the canary BUG_ON for non-TuxOnIce I/O submission. I've traced
this back to a lack of set_freezable calls in both jbd and jbd2. Since
they're clearly meant to be frozen (there are tests for freezing()), I
submit the following patch to add the missing calls.
Signed-off-by: Nigel Cunningham <nigel@tuxonice.net>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add additional KVP (Key Value Pair) protocol messages to
enhance KVP functionality for Linux guests on Hyper-V. As part of this,
patch define an explicit version negoitiation message.
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When kernel reboot, tty circular buffer is reset before last TX DMA interrupt is called,
while the buffer tail is updated in TX DMA interrupt handler. So, don't update the buffer
tail if it is reset.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28824b18ac:
|Author: Michal Nazarewicz <m.nazarewicz@samsung.com>
|Date: Wed May 5 12:53:13 2010 +0200
|
| USB: gadget: __init and __exit tags removed
|
| __init, __initdata and __exit tags have have been removed from
| various files to make it possible for gadgets that do not use
| the __init/__exit tags to use those.
obviously missed (at least) this case leading to a section mismatch in
g_ffs.c when compiling with CONFIG_USB_FUNCTIONFS_ETH enabled.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the re-coded i2c_write function from the ohci-nxp driver
in favour of using just smbus functions.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the LPC32xx to ohci-nxp
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since this driver is compatible with several NXP devices, the driver was renamed
accordingly. This patch also changes the respective symbol names.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since this driver is compatible with several NXP devices, the driver is renamed
accordingly. Please combine with the following patch which also changes the
respective symbol names.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When applying commit 7d26b58 (fix failure path in
dwc3_pci_probe()), I mistakenly left out one of the
possible failures where we would return success even
on the error case.
This patch fixes that mistake.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Non-hub device has no child, and even a real USB hub has ports far
less than USB_MAXCHILDREN, so there is no need using a fix array for
child devices, just allocate it dynamically according real port
number.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's my final pull request for 3.4. All the patches have been under
review for some time (months in some cases). The ring expansion patches
in particular have been tested by both me and Paul Zimmerman from
Synopsis.
They add support for:
- Dynamic ring expansion
- New USB 2.1 link PM errata (BESL)
- xHCI host controller support for the Synopsis DesignWare 3 IP
The dynamic ring expansion patches finally make test 10 of the host-side
test pass, instead of failing due to no room on the endpoint ring for
the larger transfers. I would have hoped that the ring expansion
patchset would make the Point Grey USB 3.0 camera work, but sadly it
fails to respond to a control transfer on my test system. This doesn't
seem to be a driver bug, but it could be a device or host bug.
Felipe has tested the patches to add a platform device to the xHCI
driver on the Synopsis DesignWare 3 IP in the TI OMAP5 board.
Please pull.
Thanks,
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7MCs
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2012-03-13' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Hi Greg,
Here's my final pull request for 3.4. All the patches have been under
review for some time (months in some cases). The ring expansion patches
in particular have been tested by both me and Paul Zimmerman from
Synopsis.
They add support for:
- Dynamic ring expansion
- New USB 2.1 link PM errata (BESL)
- xHCI host controller support for the Synopsis DesignWare 3 IP
The dynamic ring expansion patches finally make test 10 of the host-side
test pass, instead of failing due to no room on the endpoint ring for
the larger transfers. I would have hoped that the ring expansion
patchset would make the Point Grey USB 3.0 camera work, but sadly it
fails to respond to a control transfer on my test system. This doesn't
seem to be a driver bug, but it could be a device or host bug.
Felipe has tested the patches to add a platform device to the xHCI
driver on the Synopsis DesignWare 3 IP in the TI OMAP5 board.
Please pull.
Thanks,
Sarah Sharp
As described in e6fa16ab ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block
is pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this
code wrong, so using this helper function should stop that from
happening again.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
When regulatory information changes our HT behavior (e.g,
when we get a country code from the AP we have just associated
with), we should use this information to change the power with
which we transmit, and what channels we transmit. Sometimes
the channel parameters we derive from regulatory information
contradicts the parameters we used in association. For example,
we could have associated specifying HT40, but the regulatory
rules we apply may forbid HT40 operation.
In the situation above, we should reconfigure ourselves to
transmit in HT20 only, however it makes no sense for us to
disable receive in HT40, since if we associated with these
parameters, the AP has every reason to expect we can and
will receive packets this way. The code in mac80211 does
not have the capability of sending the appropriate action
frames to signal a change in HT behaviour so the AP has
no clue we can no longer receive frames encoded this way.
In some broken AP implementations, this can leave us
effectively deaf if the AP never retries in lower HT rates.
This change breaks up the channel_type parameter in the
ieee80211_enable_ht function into a separate receive and
transmit part. It honors the channel flags set by regulatory
in order to configure the rate control algorithm, but uses
the capability flags to configure the channel on the radio,
since these were used in association to set the AP's transmit
rate.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Cc: Sam Leffler <sleffler@chromium.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R Rodriguez <mcgrof@frijolero.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This value is not really very useful by itself,
yet some drivers (including iwlwifi until I can
figure out what it should do) use it. At least
rename it to "last_tsf" to indicate the meaning
and add a note that it may be really old.
I suspect the value may become useful combined
with the rx_status->mactime, but we don't (yet)
store that value and pass it to the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is intended to be the timestamp sent by the
peer in the beacon/probe response, not any form
of host timestamp. Clarify the documentation and
variable names.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The cfg80211_inform_bss() timestamp argument is
intended to be the TSF, not any form of host
timestamp.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Renaming the long fuctions and variable names from 11n_rxreoder.c
file to shorter ones for better readability.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the delay of 10 uSec or more usleep_range is prefered.
Unlike udelay, sleep_range avoids large number of undesired
interrupts.
Ref Documentation/timers/timers-howto.txt
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There exist different functions with very long names
to derive the channel frequency and power tripplet
based on band and channel/freq.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This saves some space and adds better readability.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not linearizing every SKB will help actually pass
non-linear SKBs all the way up when on an encrypted
connection. For now, linearize TKIP completely as
it is lower performance and I don't quite grok all
the details.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is better done inside the WEP decrypt
function where it doesn't have to check all
the conditions any more since they've been
tested already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent changes in udev are causing problems for drivers that load firmware
from the probe routine. As b43 has such a structure, it must be changed.
As this driver loads more than 1 firmware file, changing to the asynchronous routine
request_firmware_nowait() would be complicated. In this implementation, the probe
routine starts a queue that calls the firmware loading routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent changes in udev are causing problems for drivers that load firmware
from the probe routine. As b43legacy has such a structure, it must be changed.
As this driver loads 3 or 4 firmware files, changing to the asynchronous routine
request_firmware_nowait() would be complicated. In this implementation, the probe
routine starts a work queue that calls the firmware loading routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a fairly simple xhci-platform driver support. Currently it is
used by the dwc3 driver for supporting host mode.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
A previous commit af65cbf296 (ALSA: hdmi: fix printout of SAD sampling
rates) fixed the sample rates shown in /proc/asound/cardX/eldY and
kernel log to not be entirely wrong. However, a missing rate from the
array added in the patch causes HDMI rates 88.2 kHz, 96 kHz, 176.4 kHz,
and 192 kHz to be shown as 96 kHz, 176.4 kHz, 192 kHz, and 384 kHz,
respectively.
Fix the reporting by adding the ALSA rate 64 kHz into the conversion
array between 48 kHz and 88.2 kHz.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update sg tablesize as we can expand the ring now.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
When a urb is submitted to xHCI driver, check if queueing the urb will make
the enqueue pointer advance into dequeue seg and expand the ring if it
occurs. This is to guarantee the safety of ring expansion.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Allocate 2 segments for transfer ring by default, so we can expand the ring
when the enqueue pointer and dequeue pointer are in different segments.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
If room_on_ring() check fails, try to expand the ring and check again.
When expand a ring, use a cached ring or allocate new segments, link
the original ring and the new ring or segments, update the original ring's
segment numbers and the last segment pointer.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
In the past all the rings were allocated with cycle state equal to 1.
Now the driver may expand an existing ring, and the new segments shall be
allocated with the same cycle state as the old one.
This affects ring allocation and cached ring re-initialization.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Factor out the segments allocation and free part from ring allocation
and free routines since driver may call them directly when try to expand
a ring.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
In the past, the room_on_ring() check was implemented by walking all over
the ring, which is wasteful and complicated.
Count the number of free TRBs instead. The free TRBs number should be
updated when enqueue/dequeue pointer is updated, or upon the completion
of a set dequeue pointer command.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Store the ring's last segment pointer and number of segments for ring
expansion usage.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
