This is preparatory work for removing the individual
function pointer assignments in eeprom.c
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Finally, merge these structures and have a single
HW specific data structure.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few variables (bssid, bssidmask, curaid) were duplicated in
struct ath_softc and in ath_hal, remove them.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves all the HW version/revision specific
information into a separate structure.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the useless sc_ prefixes for all variables.
Also, refer to interfaces as VIFs and not as VAPs anymore.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts the ANI channel reference to a pointer,
this facilitates moving struct ar5416AniState to ani.h
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split the core header files into manageable pieces.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* We call reset too often and this can result various PHY problems.
On config_interface we don't need to reset the whole device.
TODO: Create a function hw_fast_reset that only resets the PCU
(tx/rx stuff) and not the whole device so that we can use this for
stuck beacons etc.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Don't enable BMISS interrupts as we don't handle them yet
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update reset and sync with HALs
* Clean up eeprom settings and tweaking of initvals and
put them on separate functions
* Set/Restore 32KHz ref clk operation
* Add some more documentation
TODO: Spur mitigation, tpc, half/quarter rate, compression etc
v2: Address comments from Bob and Felix and fix RSSI threshold bug
introduced on the first version of the patch
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update initvals to match legacy and Sam's HAL
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Use the new way to modify rf buffer and put some rf buffer
documentation on rfbufer.h
* Merge all rf regs functions to one
* Sync with legacy HAL and Sam's HAL
* Set gain_F settings so that gain_F optimization engine works
on RF5111/RF5112 (note that both HALs only use step 0 for RF5111
and they don't use gain_F optimization for this chip, code is
there but is never used)
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update and cleanup rf gain optimization code
* Add comments and refferences to docs and use sane function names
* Use only step index on ath5k_gain, no need to have a pointer to
the current step since we can determine te step from it's index,
this also allows us to put all other structs on rfgain.h and cleanup
ath5k.h a little
* No need for ah_rfgain variable, we use ah_gain.g_state for everything
* Tested on RF2112B chip but gain_F calibration is not yet done
(we will finish this on the next patch where we'll rewrite rf-buffer
handling)
* Use initial rf gain settings for 2316 and 2317 SoCs introduced on a previous patch
It seems big but it's mostly cleanup, very few functional changes have been made on phy.c
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Clean up initial rf buffer settings (new file rfbufer.h) and introduce a
new way to access specific rf registers (will use it later)
* Clean up initial rf gain settings by moving them on a new file (rfgain.h)
so we can later work on gain optimization functions
* Update initial rf buffer settings and initial rf gain settings from HALs.
This breaks things for now because our current dumps come from pre-configured
rf buffer (regdumps already had the needed values set from binary HAL).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The atomic requirement for the TSF callbacks
is outdated. get_tsf() is only called by
ieee80211_rx_bss_info() which is indirectly
called by the work queue ieee80211_sta_work().
In the same context are called several other
non-atomic functions, too.
And the atomic requirement causes problems
for drivers of USB wifi cards.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This issue happens only when we are associated with a 11n AP and power save
is enabled. In the function 'ieee80211_master_start_xmit', ps_disable_work
is queued where wake_queues is called. But before this work is executed,
we check if the queues are stopped in _ieee80211_tx and return TX_AGAIN to
ieee8011_tx which leads to the warning message.
This patch fixes this erroneous case.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just compile it into the orinoco module. If we merge USB support, the
module can then be split as appropriate.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... when used by the WEXT ioctl functions. This will allow us to
separate the card specific stuff from the WEXT code.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: Only register AC97 bus if it's not done already
ALSA: hda - Add snd_hda_multi_out_dig_cleanup()
ALSA: hda - Add missing terminator in slave dig-out array
ALSA: hda - Change HP dv7 (103c:30f4) quirk from hp-m4 to hp-dv5 model
ALSA: hda - Register (new) devices at reconfig
ALSA: mtpav - Fix initial value for input hwport
ALSA: hda - add id for Intel IbexPeak integrated HDMI codec
ALSA: hda - compute checksum in HDMI audio infoframe
ALSA: hda - enable HDMI audio pin out at module loading time
ALSA: hda - allow multi-channel HDMI audio playback when ELD is not present
ASoC: Update SDP3430 machine driver for snd_soc_card
ALSA: hda - Add quirk for Asus z37e (1043:8284)
sound: Remove OSSlib stuff from linux/soundcard.h
ASoC: WM8990: Fix kcontrol's private value use in put callback
ASoC: TLV320AIC3X: Fix kcontrol's private value use in put callback
uids in namespaces other than init don't get a sysfs entry.
For those in the init namespace, while we're waiting to remove
the sysfs entry for the uid the uid is still hashed, and
alloc_uid() may re-grab that uid without getting a new
reference to the user_ns, which we've already put in free_user
before scheduling remove_user_sysfs_dir().
Reported-and-tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ASoC supports both explicit codec drivers for AC97 devices and a simple
driver which uses the standard ALSA AC97 framework for codec support.
When used with the generic AC97 codec support that will provide the
ad hoc AC97 device for drivers like touchscreens to attach to so the
core shouldn't do so.
Reported-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While reviewing the manpages, I noticed I'd missed some clock vs timer sites.
Make sure that all timer functions call cpu_timer_sample_group() and not
cpu_clock_sample_group(). This ensures that we enable the process wide timer
in time, and therefore pay the O(n) thread group cost from the syscall.
Not doing it here, will result in the first jiffy tick after setting the timer
doing this, resulting in a very expensive tick (but only once) and a delay in
actually starting the timer.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Added the helper function snd_hda_multi_out_dig_cleanup() to clean up
the digital outputs with multi setup. This call is needed in cases
the codec supports multiple digital outputs as slaves. Otherwise the
slave widgets aren't properly cleaned up.
For a single digital output (e.g. in patch_conexant.c), this call isn't
needed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Between 2.6.23 and 2.6.24-rc1 a change was made that broke IBM LS21
systems that had the HPET enabled in the BIOS, resulting in boot hangs
for x86_64.
Specifically commit b8ce335906, which
merges the i386 and x86_64 HPET code.
Prior to this commit, when we setup the HPET timers in x86_64, we did
the following:
hpet_writel(HPET_TN_ENABLE | HPET_TN_PERIODIC | HPET_TN_SETVAL |
HPET_TN_32BIT, HPET_T0_CFG);
However after the i386/x86_64 HPET merge, we do the following:
cfg = hpet_readl(HPET_Tn_CFG(timer));
cfg |= HPET_TN_ENABLE | HPET_TN_PERIODIC |
HPET_TN_SETVAL | HPET_TN_32BIT;
hpet_writel(cfg, HPET_Tn_CFG(timer));
However on LS21s with HPET enabled in the BIOS, the HPET_T0_CFG register
boots with Level triggered interrupts (HPET_TN_LEVEL) enabled. This
causes the periodic interrupt to be not so periodic, and that results in
the boot time hang I reported earlier in the delay calibration.
My fix: Always disable HPET_TN_LEVEL when setting up periodic mode.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Change HP dv7 quirk: although reported to work with hp-m4 model
(https://bugzilla.novell.com/show_bug.cgi?id=445321), the original
report doesn't contain info about testing of internal microphone.
Recently I received a report about internal mic not working
(https://qa.mandriva.com/show_bug.cgi?id=44855#c193), this must be
related with the forced line in on pin 0x0e done with hp-m4 model. Thus
change the current quirk from STAC_HP_M4 to STAC_HP_DV5, later reported
to be fixed on a provided kernel with this change
(https://qa.mandriva.com/show_bug.cgi?id=44855#c196).
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the VSX alignment handler for VSX registers > 32. 32-63 are stored
in the VMX part of the thread_struct not the FPR part.
Signed-off-by: Michael Neuling <mikey@neuling.org>
CC: stable@kernel.org (2.6.27 & .28 please)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change the PS3 hotplug memory routine ps3_mm_add_memory() from
a core_initcall to a device_initcall.
core_initcall routines run before the powerpc topology_init()
startup routine, which is a subsys_initcall, resulting in
failure of ps3_mm_add_memory() when CONFIG_NUMA=y. When
ps3_mm_add_memory() fails the system will boot with just the
128 MiB of boot memory
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix the powerpc NUMA reserve bootmem page selection logic.
commit 8f64e1f2d1 (powerpc: Reserve
in bootmem lmb reserved regions that cross NUMA nodes) changed
the logic for how the powerpc LMB reserved regions were converted
to bootmen reserved regions. As the folowing discussion reports,
the new logic was not correct.
mark_reserved_regions_for_nid() goes through each LMB on the
system that specifies a reserved area. It searches for
active regions that intersect with that LMB and are on the
specified node. It attempts to bootmem-reserve only the area
where the active region and the reserved LMB intersect. We
can not reserve things on other nodes as they may not have
bootmem structures allocated, yet.
We base the size of the bootmem reservation on two possible
things. Normally, we just make the reservation start and
stop exactly at the start and end of the LMB.
However, the LMB reservations are not aware of NUMA nodes and
on occasion a single LMB may cross into several adjacent
active regions. Those may even be on different NUMA nodes
and will require separate calls to the bootmem reserve
functions. So, the bootmem reservation must be trimmed to
fit inside the current active region.
That's all fine and dandy, but we trim the reservation
in a page-aligned fashion. That's bad because we start the
reservation at a non-page-aligned address: physbase.
The reservation may only span 2 bytes, but that those bytes
may span two pfns and cause a reserve_size of 2*PAGE_SIZE.
Take the case where you reserve 0x2 bytes at 0x0fff and
where the active region ends at 0x1000. You'll jump into
that if() statment, but node_ar.end_pfn=0x1 and
start_pfn=0x0. You'll end up with a reserve_size=0x1000,
and then call
reserve_bootmem_node(node, physbase=0xfff, size=0x1000);
0x1000 may not be on the same node as 0xfff. Oops.
In almost all the vm code, end_<anything> is not inclusive.
If you have an end_pfn of 0x1234, page 0x1234 is not
included in the range. Using PFN_UP instead of the
(>> >> PAGE_SHIFT) will make this consistent with the other VM
code.
We also need to do math for the reserved size with physbase
instead of start_pfn. node_ar.end_pfn << PAGE_SHIFT is
*precisely* the end of the node. However,
(start_pfn << PAGE_SHIFT) is *NOT* precisely the beginning
of the reserved area. That is, of course, physbase.
If we don't use physbase here, the reserve_size can be
made too large.
From: Dave Hansen <dave@linux.vnet.ibm.com>
Tested-by: Geoff Levand <geoffrey.levand@am.sony.com> Tested on PS3.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix _PAGE_CHG_MASK so that pte_modify() does not affect the _PAGE_SPECIAL bit.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
wimax: fix oops in wimax_dev_get_by_genl_info() when looking up non-wimax iface
net: 4 bytes kernel memory disclosure in SO_BSDCOMPAT gsopt try #2
netxen: fix compile waring "label ‘set_32_bit_mask’ defined but not used" on IA64 platform
bnx2: Update version to 1.9.2 and copyright.
bnx2: Fix jumbo frames error handling.
bnx2: Update 5709 firmware.
bnx2: Update 5706/5708 firmware.
3c505: do not set pcb->data.raw beyond its size
Documentation/connector/cn_test.c: don't use gfp_any()
net: don't use in_atomic() in gfp_any()
IRDA: cnt is off by 1
netxen: remove pcie workaround
sun3: print when lance_open() fails
qlge: bugfix: Add missing rx buf clean index on early exit.
qlge: bugfix: Fix RX scaling values.
qlge: bugfix: Fix TSO breakage.
qlge: bugfix: Add missing dev_kfree_skb_any() call.
qlge: bugfix: Add missing put_page() call.
qlge: bugfix: Fix fatal error recovery hang.
qlge: bugfix: Use netif_receive_skb() and vlan_hwaccel_receive_skb().
...
When a non-wimax interface is looked up by the stack, a bad pointer is
returned when the looked-up interface is not found in the list (of
registered WiMAX interfaces). This causes an oops in the caller when
trying to use the pointer.
Fix by properly setting the pointer to NULL if we don't exit from the
list_for_each() with a found entry.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function sock_getsockopt() located in net/core/sock.c, optval v.val
is not correctly initialized and directly returned in userland in case
we have SO_BSDCOMPAT option set.
This dummy code should trigger the bug:
int main(void)
{
unsigned char buf[4] = { 0, 0, 0, 0 };
int len;
int sock;
sock = socket(33, 2, 2);
getsockopt(sock, 1, SO_BSDCOMPAT, &buf, &len);
printf("%x%x%x%x\n", buf[0], buf[1], buf[2], buf[3]);
close(sock);
}
Here is a patch that fix this bug by initalizing v.val just after its
declaration.
Signed-off-by: Clément Lecigne <clement.lecigne@netasq.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compile the latest kernel on IA64 platform,I got a warning:
drivers/net/netxen/netxen_nic_main.c:203: warning: label ‘set_32_bit_mask’
defined but not used
We do not need label ‘set_32_bit_mask’ on IA64 platform,So move it to #else.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If errors are reported on a frame descriptor, we need to
account for the buffer pages that may have been used for this
error packet and recycle them. Otherwise, we may get the wrong
pages for the next packet.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers. In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers. In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we do not set pcb->data.raw beyond its size, print an error message
and return false if we attempt to. A timout message was printed one too early.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
