Example scenario:
Parent snapshot:
. (ino 277)
|---- tmp/ (ino 278)
|---- pre/ (ino 280)
| |---- wait_dir/ (ino 281)
|
|---- desc/ (ino 282)
|---- ance/ (ino 283)
| |---- below_ance/ (ino 279)
|
|---- other_dir/ (ino 284)
Send snapshot:
. (ino 277)
|---- tmp/ (ino 278)
|---- other_dir/ (ino 284)
|---- below_ance/ (ino 279)
| |---- pre/ (ino 280)
|
|---- wait_dir/ (ino 281)
|---- desc/ (ino 282)
|---- ance/ (ino 283)
While computing the send stream the following steps happen:
1) While processing inode 279 we end up delaying its rename operation
because its new parent in the send snapshot, inode 284, was not
yet processed and therefore not yet renamed;
2) Later when processing inode 280 we end up renaming it immediately to
"ance/below_once/pre" and not delay its rename operation because its
new parent (inode 279 in the send snapshot) has its rename operation
delayed and inode 280 is not an encestor of inode 279 (its parent in
the send snapshot) in the parent snapshot;
3) When processing inode 281 we end up delaying its rename operation
because its new parent in the send snapshot, inode 284, was not yet
processed and therefore not yet renamed;
4) When processing inode 282 we do not delay its rename operation because
its parent in the send snapshot, inode 281, already has its own rename
operation delayed and our current inode (282) is not an ancestor of
inode 281 in the parent snapshot. Therefore inode 282 is renamed to
"ance/below_ance/pre/wait_dir";
5) When processing inode 283 we realize that we can rename it because one
of its ancestors in the send snapshot, inode 281, has its rename
operation delayed and inode 283 is not an ancestor of inode 281 in the
parent snapshot. So a rename operation to rename inode 283 to
"ance/below_ance/pre/wait_dir/desc/ance" is issued. This path is
invalid due to a missing path building loop that was undetected by
the incremental send implementation, as inode 283 ends up getting
included twice in the path (once with its path in the parent snapshot).
Therefore its rename operation must wait before the ancestor inode 284
is renamed.
Fix this by not terminating the rename dependency checks when we find an
ancestor, in the send snapshot, that has its rename operation delayed. So
that we continue doing the same checks if the current inode is not an
ancestor, in the parent snapshot, of an ancestor in the send snapshot we
are processing in the loop.
The problem and reproducer were reported by Robbie Ko, as part of a patch
titled "Btrfs: incremental send, avoid ancestor rename to descendant".
However the fix was unnecessarily complicated and can be addressed with
much less code and effort.
Reported-by: Robbie Ko <robbieko@synology.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
The function path_loop() can return a negative integer, signaling an
error, 0 if there's no path loop and 1 if there's a path loop. We were
treating any non zero values as meaning that a path loop exists. Fix
this by explicitly checking for errors and gracefully return them to
user space.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
When doing an incremental send we can end up not moving directories that
have the same name. This happens when the same parent directory has
different child directories with the same name in the parent and send
snapshots.
For example, consider the following scenario:
Parent snapshot:
. (ino 256)
|---- d/ (ino 257)
| |--- p1/ (ino 258)
|
|---- p1/ (ino 259)
Send snapshot:
. (ino 256)
|--- d/ (ino 257)
|--- p1/ (ino 259)
|--- p1/ (ino 258)
The directory named "d" (inode 257) has in both snapshots an entry with
the name "p1" but it refers to different inodes in both snapshots (inode
258 in the parent snapshot and inode 259 in the send snapshot). When
attempting to move inode 258, the operation is delayed because its new
parent, inode 259, was not yet moved/renamed (as the stream is currently
processing inode 258). Then when processing inode 259, we also end up
delaying its move/rename operation so that it happens after inode 258 is
moved/renamed. This decision to delay the move/rename rename operation
of inode 259 is due to the fact that the new parent inode (257) still
has inode 258 as its child, which has the same name has inode 259. So
we end up with inode 258 move/rename operation waiting for inode's 259
move/rename operation, which in turn it waiting for inode's 258
move/rename. This results in ending the send stream without issuing
move/rename operations for inodes 258 and 259 and generating the
following warnings in syslog/dmesg:
[148402.979747] ------------[ cut here ]------------
[148402.980588] WARNING: CPU: 14 PID: 4117 at fs/btrfs/send.c:6177 btrfs_ioctl_send+0xe03/0xe51 [btrfs]
[148402.981928] Modules linked in: btrfs crc32c_generic xor raid6_pq acpi_cpufreq tpm_tis ppdev tpm parport_pc psmouse parport sg pcspkr i2c_piix4 i2c_core evdev processor serio_raw button loop autofs4 ext4 crc16 jbd2 mbcache sr_mod cdrom sd_mod ata_generic virtio_scsi ata_piix libata virtio_pci virtio_ring virtio e1000 scsi_mod floppy [last unloaded: btrfs]
[148402.986999] CPU: 14 PID: 4117 Comm: btrfs Tainted: G W 4.6.0-rc7-btrfs-next-31+ #1
[148402.988136] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS by qemu-project.org 04/01/2014
[148402.988136] 0000000000000000 ffff88022139fca8 ffffffff8126b42c 0000000000000000
[148402.988136] 0000000000000000 ffff88022139fce8 ffffffff81052b14 000018212139fac8
[148402.988136] ffff88022b0db400 0000000000000000 0000000000000001 0000000000000000
[148402.988136] Call Trace:
[148402.988136] [<ffffffff8126b42c>] dump_stack+0x67/0x90
[148402.988136] [<ffffffff81052b14>] __warn+0xc2/0xdd
[148402.988136] [<ffffffff81052beb>] warn_slowpath_null+0x1d/0x1f
[148402.988136] [<ffffffffa04bc831>] btrfs_ioctl_send+0xe03/0xe51 [btrfs]
[148402.988136] [<ffffffffa048b358>] btrfs_ioctl+0x14f/0x1f81 [btrfs]
[148402.988136] [<ffffffff8108e456>] ? arch_local_irq_save+0x9/0xc
[148402.988136] [<ffffffff8108eb51>] ? __lock_is_held+0x3c/0x57
[148402.988136] [<ffffffff8118da05>] vfs_ioctl+0x18/0x34
[148402.988136] [<ffffffff8118e00c>] do_vfs_ioctl+0x550/0x5be
[148402.988136] [<ffffffff81196f0c>] ? __fget+0x6b/0x77
[148402.988136] [<ffffffff81196fa1>] ? __fget_light+0x62/0x71
[148402.988136] [<ffffffff8118e0d1>] SyS_ioctl+0x57/0x79
[148402.988136] [<ffffffff8149e025>] entry_SYSCALL_64_fastpath+0x18/0xa8
[148402.988136] [<ffffffff8108e89d>] ? trace_hardirqs_off_caller+0x3f/0xaa
[148403.011373] ---[ end trace a4539270c8056f8b ]---
[148403.012296] ------------[ cut here ]------------
[148403.013071] WARNING: CPU: 14 PID: 4117 at fs/btrfs/send.c:6194 btrfs_ioctl_send+0xe19/0xe51 [btrfs]
[148403.014447] Modules linked in: btrfs crc32c_generic xor raid6_pq acpi_cpufreq tpm_tis ppdev tpm parport_pc psmouse parport sg pcspkr i2c_piix4 i2c_core evdev processor serio_raw button loop autofs4 ext4 crc16 jbd2 mbcache sr_mod cdrom sd_mod ata_generic virtio_scsi ata_piix libata virtio_pci virtio_ring virtio e1000 scsi_mod floppy [last unloaded: btrfs]
[148403.019708] CPU: 14 PID: 4117 Comm: btrfs Tainted: G W 4.6.0-rc7-btrfs-next-31+ #1
[148403.020104] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS by qemu-project.org 04/01/2014
[148403.020104] 0000000000000000 ffff88022139fca8 ffffffff8126b42c 0000000000000000
[148403.020104] 0000000000000000 ffff88022139fce8 ffffffff81052b14 000018322139fac8
[148403.020104] ffff88022b0db400 0000000000000000 0000000000000001 0000000000000000
[148403.020104] Call Trace:
[148403.020104] [<ffffffff8126b42c>] dump_stack+0x67/0x90
[148403.020104] [<ffffffff81052b14>] __warn+0xc2/0xdd
[148403.020104] [<ffffffff81052beb>] warn_slowpath_null+0x1d/0x1f
[148403.020104] [<ffffffffa04bc847>] btrfs_ioctl_send+0xe19/0xe51 [btrfs]
[148403.020104] [<ffffffffa048b358>] btrfs_ioctl+0x14f/0x1f81 [btrfs]
[148403.020104] [<ffffffff8108e456>] ? arch_local_irq_save+0x9/0xc
[148403.020104] [<ffffffff8108eb51>] ? __lock_is_held+0x3c/0x57
[148403.020104] [<ffffffff8118da05>] vfs_ioctl+0x18/0x34
[148403.020104] [<ffffffff8118e00c>] do_vfs_ioctl+0x550/0x5be
[148403.020104] [<ffffffff81196f0c>] ? __fget+0x6b/0x77
[148403.020104] [<ffffffff81196fa1>] ? __fget_light+0x62/0x71
[148403.020104] [<ffffffff8118e0d1>] SyS_ioctl+0x57/0x79
[148403.020104] [<ffffffff8149e025>] entry_SYSCALL_64_fastpath+0x18/0xa8
[148403.020104] [<ffffffff8108e89d>] ? trace_hardirqs_off_caller+0x3f/0xaa
[148403.038981] ---[ end trace a4539270c8056f8c ]---
There's another issue caused by similar (but more complex) changes in the
directory hierarchy that makes move/rename operations fail, described with
the following example:
Parent snapshot:
.
|---- a/ (ino 262)
| |---- c/ (ino 268)
|
|---- d/ (ino 263)
|---- ance/ (ino 267)
|---- e/ (ino 264)
|---- f/ (ino 265)
|---- ance/ (ino 266)
Send snapshot:
.
|---- a/ (ino 262)
|---- c/ (ino 268)
| |---- ance/ (ino 267)
|
|---- d/ (ino 263)
| |---- ance/ (ino 266)
|
|---- f/ (ino 265)
|---- e/ (ino 264)
When the inode 265 is processed, the path for inode 267 is computed, which
at that time corresponds to "d/ance", and it's stored in the names cache.
Later on when processing inode 266, we end up orphanizing (renaming to a
name matching the pattern o<ino>-<gen>-<seq>) inode 267 because it has
the same name as inode 266 and it's currently a child of the new parent
directory (inode 263) for inode 266. After the orphanization and while we
are still processing inode 266, a rename operation for inode 266 is
generated. However the source path for that rename operation is incorrect
because it ends up using the old, pre-orphanization, name of inode 267.
The no longer valid name for inode 267 was previously cached when
processing inode 265 and it remains usable and considered valid until
the inode currently being processed has a number greater than 267.
This resulted in the receiving side failing with the following error:
ERROR: rename d/ance/ance -> d/ance failed: No such file or directory
So fix these issues by detecting such circular dependencies for rename
operations and by clearing the cached name of an inode once the inode
is orphanized.
A test case for fstests will follow soon.
Signed-off-by: Robbie Ko <robbieko@synology.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
[Rewrote change log to be more detailed and organized, and improved
comments]
Signed-off-by: Filipe Manana <fdmanana@suse.com>
When we start an fsync we start ordered extents for all delalloc ranges.
However before attempting to log the inode, we only wait for those ordered
extents if we are not doing a full sync (bit BTRFS_INODE_NEEDS_FULL_SYNC
is set in the inode's flags). This means that if an ordered extent
completes with an IO error before we check if we can skip logging the
inode, we will not catch and report the IO error to user space. This is
because on an IO error, when the ordered extent completes we do not
update the inode, so if the inode was not previously updated by the
current transaction we end up not logging it through calls to fsync and
therefore not check its mapping flags for the presence of IO errors.
Fix this by checking for errors in the flags of the inode's mapping when
we notice we can skip logging the inode.
This caused sporadic failures in the test generic/331 (which explicitly
tests for IO errors during an fsync call).
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
There are KSZ8721 PHYs with phy_id 0x00221619. In order to detect them
as PHY_ID_KSZ8001 compatible while staying different to PHY_ID_KSZ9021
ignore the last two bits when matching PHY_ID
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chunhao Lin says:
====================
r8169: fix 3 runtime pm related issues.
v2:
use "struct device *d = &tp->pci_dev->dev" instead of "struct pci_dev *pdev = tp->pci_dev"
v1:
This series of patches fix 3 runtime pm related issues that are listed below.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is no AC power, NIC may not work after changing mac address.
Please refer to following link.
http://www.spinics.net/lists/netdev/msg356572.html
This issue is caused by runtime power management. When there is no AC
power, if we put NIC down (ifconfig down), the driver will be in runtime
suspend state and hardware will be put into D3 state. During this time,
driver cannot access hardware regisers. So if you set new mac address
during this time, it will not be set to hardware. After resume, NIC will
keep using the old mac address and the network will not work normally.
In this patch I add detecting runtime pm status when setting mac address.
If driver is in runtime suspend state, it will skip setting mac address, keep
the new mac address, and set the new mac address during runtime resume.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not to call rtl8169_update_counters() to dump tally counter when driver
is in runtime suspend state.
Calling rtl8169_update_counters() in runtime suspend state will produce
warning message "rtl_counters_cond == 1 (loop: 1000, delay: 10)".
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC will be put into D3 state during runtime suspend state. When set or
get hardware wol setting, driver will write or read hardware registers.
If we set or get hardware wol setting in runtime suspend state, because
NIC will in D3 state, the hardware registers read by driver will return all
0xff. That will let driver thinking register flag is not toggled and
then prints the warning message "rtl_counters_cond == 1 (loop: 1000,
delay: 10)" to kernel log.
For fixing this issue, add checking driver's pm runtime status in
rtl8169_get_wol() and rtl8169_set_wol().
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- A couple of changes to improve the support for erase/discard/trim cmds
- Add eMMC HS400 enhanced strobe support
- Show OCR and DSR registers in SYSFS for MMC/SD cards
- Correct and improve busy detection logic for MMC switch (CMD6) cmds
- Disable HPI cmds for certain broken Hynix eMMC cards
- Allow MMC hosts to specify non-support for SD and MMC cmds
- Some minor additional fixes
MMC host:
- sdhci: Re-works, fixes and clean-ups
- sdhci: Add HW auto re-tuning support
- sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
- sdhci-esdhc-imx: Fixes and clean-ups
- sdhci-esdhc-imx: Update system PM support
- sdhci-esdhc-imx: Enable HW auto re-tuning
- sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
- sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
- sdhci-msm: Add support for UHS cards
- sdhci-tegra: Improve support for UHS cards
- sdhci-of-arasan: Update phy support for Rockchip SoCs
- sdhci-of-arasan: Deploy enhanced strobe support
- dw_mmc: Some fixes and clean-ups
- dw_mmc: Enable support for erase/discard/trim cmds
- dw_mmc: Enable CMD23 support
- mediatek: Some fixes related to the eMMC HS400 support
- sh_mmcif: Improve support for HW busy detection
- rtsx_pci: Enable support for erase/discard/trim cmds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wzSC
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- A couple of changes to improve the support for erase/discard/trim cmds
- Add eMMC HS400 enhanced strobe support
- Show OCR and DSR registers in SYSFS for MMC/SD cards
- Correct and improve busy detection logic for MMC switch (CMD6) cmds
- Disable HPI cmds for certain broken Hynix eMMC cards
- Allow MMC hosts to specify non-support for SD and MMC cmds
- Some minor additional fixes
MMC host:
- sdhci: Re-works, fixes and clean-ups
- sdhci: Add HW auto re-tuning support
- sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
- sdhci-esdhc-imx: Fixes and clean-ups
- sdhci-esdhc-imx: Update system PM support
- sdhci-esdhc-imx: Enable HW auto re-tuning
- sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
- sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
- sdhci-msm: Add support for UHS cards
- sdhci-tegra: Improve support for UHS cards
- sdhci-of-arasan: Update phy support for Rockchip SoCs
- sdhci-of-arasan: Deploy enhanced strobe support
- dw_mmc: Some fixes and clean-ups
- dw_mmc: Enable support for erase/discard/trim cmds
- dw_mmc: Enable CMD23 support
- mediatek: Some fixes related to the eMMC HS400 support
- sh_mmcif: Improve support for HW busy detection
- rtsx_pci: Enable support for erase/discard/trim cmds"
* tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc: (135 commits)
mmc: rtsx_pci: Remove deprecated create_singlethread_workqueue
mmc: rtsx_pci: Enable MMC_CAP_ERASE to allow erase/discard/trim requests
mmc: rtsx_pci: Use the provided busy timeout from the mmc core
mmc: sdhci-pltfm: Drop define for SDHCI_PLTFM_PMOPS
mmc: sdhci-pltfm: Convert to use the SET_SYSTEM_SLEEP_PM_OPS
mmc: sdhci-pltfm: Make sdhci_pltfm_suspend|resume() static
mmc: sdhci-esdhc-imx: Use common sdhci_suspend|resume_host()
mmc: sdhci-esdhc-imx: Assign system PM ops within #ifdef CONFIG_PM_SLEEP
mmc: sdhci-sirf: Remove non needed #ifdef CONFIG_PM* for dev_pm_ops
mmc: sdhci-s3c: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
mmc: sdhci-pxav3: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
mmc: sdhci-of-esdhc: Simplify code by using SIMPLE_DEV_PM_OPS
mmc: sdhci-acpi: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
mmc: sdhci-pci-core: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
mmc: Change the max discard sectors and erase response when HW busy detect
phy: rockchip-emmc: Wait even longer for the DLL to lock
phy: rockchip-emmc: Be tolerant to card clock of 0 in power on
mmc: sdhci-of-arasan: Revert: Always power the PHY off/on when clock changes
mmc: sdhci-msm: Add support for UHS cards
mmc: sdhci-msm: Add set_uhs_signaling() implementation
...
Pull watchdog updates from Wim Van Sebroeck:
"Core:
- min and max timeout improvements, WDOG_HW_RUNNING improvements,
status funtionality
- Add a device managed API for watchdog_register_device()
New watchdog drivers:
- Aspeed SoCs
- Maxim PMIC MAX77620
- Amlogic Meson GXBB SoC
Enhancements:
- support for the r8a7796 watchdog device
- support for F81866 watchdog device
- support for 5th variation of Apollo Lake
- support for MCP78S chipset
- clean-up of softdog.c watchdog device driver
- pic32-wdt and pic32-dmt fixes
- Documentation/watchdog: watchdog-test improvements
- several other fixes and improvements"
* git://www.linux-watchdog.org/linux-watchdog: (50 commits)
watchdog: gpio_wdt: Fix missing platform_set_drvdata() in gpio_wdt_probe()
watchdog: core: Clear WDOG_HW_RUNNING before calling the stop function
watchdog: core: Fix error handling of watchdog_dev_init()
watchdog: pic32-wdt: Fix return value check in pic32_wdt_drv_probe()
watchdog: pic32-dmt: Remove .owner field for driver
watchdog: pic32-wdt: Remove .owner field for driver
watchdog: renesas-wdt: Add support for the r8a7796 wdt
Documentation/watchdog: check return value for magic close
watchdog: sbsa: Drop status function
watchdog: Implement status function in watchdog core
watchdog: tangox: Set max_hw_heartbeat_ms instead of max_timeout
watchdog: change watchdog_need_worker logic
watchdog: add support for MCP78S chipset in nv_tco
watchdog: bcm2835_wdt: remove redundant ->set_timeout callback
watchdog: bcm2835_wdt: constify _ops and _info structures
dt-bindings: watchdog: Add Meson GXBB Watchdog bindings
watchdog: Add Meson GXBB Watchdog Driver
watchdog: qcom: configure BARK time in addition to BITE time
watchdog: qcom: add option for standalone watchdog not in timer block
watchdog: qcom: update device tree bindings
...
Pull btrfs updates from Chris Mason:
"This pull is dedicated to Josef's enospc rework, which we've been
testing for a few releases now. It fixes some early enospc problems
and is dramatically faster.
This also includes an updated fix for the delalloc accounting that
happens after a fault in copy_from_user. My patch in v4.7 was almost
but not quite enough"
* 'for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix delalloc accounting after copy_from_user faults
Btrfs: avoid deadlocks during reservations in btrfs_truncate_block
Btrfs: use FLUSH_LIMIT for relocation in reserve_metadata_bytes
Btrfs: fill relocation block rsv after allocation
Btrfs: always use trans->block_rsv for orphans
Btrfs: change how we calculate the global block rsv
Btrfs: use root when checking need_async_flush
Btrfs: don't bother kicking async if there's nothing to reclaim
Btrfs: fix release reserved extents trace points
Btrfs: add fsid to some tracepoints
Btrfs: add tracepoints for flush events
Btrfs: fix delalloc reservation amount tracepoint
Btrfs: trace pinned extents
Btrfs: introduce ticketed enospc infrastructure
Btrfs: add tracepoint for adding block groups
Btrfs: warn_on for unaccounted spaces
Btrfs: change delayed reservation fallback behavior
Btrfs: always reserve metadata for delalloc extents
Btrfs: fix callers of btrfs_block_rsv_migrate
Btrfs: add bytes_readonly to the spaceinfo at once
This patch enables support for Performance monitor registers related
ELF core note NT_PPC_PMU based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding one new register sets REGSET_PMU in powerpc
corresponding to the ELF core note sections added in this
regard. It also implements the get, set and active functions
for this new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for EBB state registers related
ELF core note NT_PPC_EBB based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding one new register sets REGSET_EBB in powerpc
corresponding to the ELF core note sections added in this
regard. It also implements the get, set and active functions
for this new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for running TAR, PPR, DSCR registers
related ELF core notes NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR based
ptrace requests through PTRACE_GETREGSET, PTRACE_SETREGSET calls.
This is achieved through adding three new register sets REGSET_TAR,
REGSET_PPR, REGSET_DSCR in powerpc corresponding to the ELF core
note sections added in this regad. It implements the get, set and
active functions for all these new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for all three TM checkpointed SPR
states related ELF core note NT_PPC_TM_CTAR, NT_PPC_TM_CPPR,
NT_PPC_TM_CDSCR based ptrace requests through PTRACE_GETREGSET,
PTRACE_SETREGSET calls. This is achieved through adding three
new register sets REGSET_TM_CTAR, REGSET_TM_CPPR and
REGSET_TM_CDSCR in powerpc corresponding to the ELF core note
sections added. It implements the get, set and active functions
for all these new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM SPR state related ELF core
note NT_PPC_TM_SPR based ptrace requests through PTRACE_GETREGSET,
PTRACE_SETREGSET calls. This is achieved through adding a register
set REGSET_TM_SPR in powerpc corresponding to the ELF core note
section added. It implements the get, set and active functions for
this new register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed VSX register
set ELF core note NT_PPC_CVSX based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CVSX in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed VMX register
set ELF core note NT_PPC_CVMX based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CVMX in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed FPR register
set ELF core note NT_PPC_CFPR based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CFPR in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed GPR register
set ELF core note NT_PPC_CGPR based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CGPR in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch splits gpr32_get, gpr32_set functions to accommodate
in transaction ptrace requests implemented in patches later in
the series.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables in transaction NT_PPC_VSX ptrace requests. The
function vsr_get which gets the running value of all VSX registers
and the function vsr_set which sets the running value of of all VSX
registers work on the running set of VMX registers whose location
will be different if transaction is active. This patch makes these
functions adapt to situations when the transaction is active.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables in transaction NT_PPC_VMX ptrace requests. The
function vr_get which gets the running value of all VMX registers
and the function vr_set which sets the running value of of all VMX
registers work on the running set of VMX registers whose location
will be different if transaction is active. This patch makes these
functions adapt to situations when the transaction is active.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables in transaction NT_PRFPREG ptrace requests.
The function fpr_get which gets the running value of all FPR
registers and the function fpr_set which sets the running
value of of all FPR registers work on the running set of FPR
registers whose location will be different if transaction is
active. This patch makes these functions adapt to situations
when the transaction is active.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch creates a function flush_tmregs_to_thread which
will then be used by subsequent patches in this series. The
function checks for self tracing ptrace interface attempts
while in the TM context and logs appropriate warning message.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds twelve ELF core note sections for powerpc
architecture for various registers and register sets which
need to be accessed from ptrace interface and then gdb.
These additions include special purpose registers like TAR,
PPR, DSCR, TM running and checkpointed state for various
register sets, EBB related register set, performance monitor
register set etc. Addition of these new ELF core note
sections extends the existing ELF ABI on powerpc arch without
affecting it in any manner.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This should be same as flush_tlb_page except for hash32. For hash32
I guess the existing code is wrong, because we don't seem to be
flushing tlb for Hash != 0 case at all. Fix this by switching to
calling flush_tlb_page() which does the right thing by flushing
tlb for both hash and nohash case with hash32
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some archs like ppc64 need to do special things when flushing tlb for
hugepage. Add a new helper to flush hugetlb tlb range. This helps us to
avoid flushing the entire tlb mapping for the pid.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use the helper instead of open coding the same at multiple place
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of flushing the entire mm, implement a flush_pmd_tlb_range
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use flush_hugetlb_page instead of flush_tlb_page when we clear flush the
pte.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Replace opencoding of the same at multiple places with the helper.
No functional change with this patch.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we track page size in mmu_gather, we can use address based
tlbie format when doing a tlb_flush(). We don't do this if we are
invalidating the full address space.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a comment to the generated assembler for jump labels. This makes it
easier to identify them in asm listings (generated with $ make foo.s).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This allows us to catch incorrect usage of cpu_has_feature() and
mmu_has_feature() prior to jump labels being initialised.
mpe: Use printk() and dump_stack() rather than WARN_ON(), because
WARN_ON() may not work this early in boot. Rename the Kconfig.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As we just did for CPU features.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We do binary patching of asm code using CPU features, which is a
one-time operation, done during early boot. However checks of CPU
features in C code are currently done at run time, even though the set
of CPU features can never change after boot.
We can optimise this by using jump labels to implement cpu_has_feature(),
meaning checks in C code are binary patched into a single nop or branch.
For a C sequence along the lines of:
if (cpu_has_feature(FOO))
return 2;
The generated code before is roughly:
ld r9,-27640(r2)
ld r9,0(r9)
lwz r9,32(r9)
cmpwi cr7,r9,0
bge cr7, 1f
li r3,2
blr
1: ...
After (true):
nop
li r3,2
blr
After (false):
b 1f
li r3,2
blr
1: ...
mpe: Rename MAX_CPU_FEATURES as we already have a #define with that
name, and define it simply as a constant, rather than doing tricks with
sizeof and NULL pointers. Rename the array to cpu_feature_keys. Use the
kconfig we added to guard it. Add BUILD_BUG_ON() if the feature is not a
compile time constant. Rewrite the change log.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a kconfig option to control whether we use jump label for the
cpu/mmu_has_feature() checks. Currently this does nothing, but we will
enabled it in the subsequent patches.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We plan to use jump label for cpu_has_feature(). In order to implement
this we need to include the linux/jump_label.h in asm/cputable.h.
Unfortunately if we do that it leads to an include loop. The root of the
problem seems to be that reg.h needs cputable.h (for CPU_FTRs), and then
cputable.h via jump_label.h eventually pulls in hw_irq.h which needs
reg.h (for MSR_EE).
So move cpu_has_feature() to a separate file on its own.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Rename to cpu_has_feature.h and flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This function is only used by get_vtb(). They are almost the same except
the reading from the real register. Move the mfspr() to get_vtb() and
kill the function mfvtb(). With this, we can eliminate the use of
cpu_has_feature() in very core header file like reg.h. This is a
preparation for the use of jump label for cpu_has_feature().
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Call jump_label_init() early so that we can use static keys for CPU and
MMU feature checks.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some arches (powerpc at least) would like to invoke jump_label_init()
much earlier in boot. So check static_key_initialized in order to make
sure this function runs only once.
LGTM-by: Ingo (http://marc.info/?l=linux-kernel&m=144049104329961&w=2)
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This switches early feature checks to use the non static key variant of
the function. In later patches we will be switching cpu_has_feature()
and mmu_has_feature() to use static keys and we can use them only after
static key/jump label is initialized. Any check for feature before jump
label init should be done using this new helper.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In later patches, we will be switching CPU and MMU feature checks to
use static keys.
For checks in early boot before jump label is initialized we need a
variant of [cpu|mmu]_has_feature() that doesn't use jump labels.
So create those called, unimaginatively, early_[cpu|mmu]_has_feature().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we have radix_enabled() three times, twice in asm/book3s/64/mmu.h
and then a fallback in asm/mmu.h.
Consolidate them in asm/mmu.h. While we're at it convert them to be
static inlines, and change the fallback case to returning a bool, like
mmu_has_feature().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The intention is that the result is only used as a boolean, so enforce
that by changing the return type to bool.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The intention is that the result is only used as a boolean, so enforce
that by changing the return type to bool.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
