Kay says i2c adapters shouldn't be class devices but bus devices.
Convert them that way, using a device type.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Make the I/O faster, mainly by using combined SMBus transactions when
possible. While the TSL2550 datasheet doesn't say the device supports
them, they seem to work just fine in practice, and a combined
transaction is faster than two simple transactions in many cases and
always more reliable.
A side effect is to suppress the delays between SMBus writes and
reads. The datasheet doesn't say they are needed and things work just
fine for me without them.
I also couldn't see any reason for the delay between reading the two
channels. Nor for the loop to get a reading in the first place. The
400 ms delay between samples only matters at chip power-up, after that
the chip always hold the previously sampled value so we never get to
wait.
All these changes make reading the lux value much faster and cheaper.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michele De Candia <michele.decandia@valueteam.com>
Cc: Rodolfo Giometti <giometti@linux.it>
When echo is on, we waste time reading back our orders. Switching echo
off makes performance much better: SMBus byte data transactions are 47%
faster and byte transactions are 24% faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The allocator has some nice knobs for sending hints about where
to try and allocate new blocks, but when we're doing file allocations
we're not sending any hint at all.
This commit adds a simple extent map search to see if we can
quickly and easily find a hint for the allocator.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When btrfs fills a delayed allocation, it tries to increase
the wbc nr_to_write to cover a big part of allocation. The
theory is that we're doing contiguous IO and writing a few
more blocks will save seeks overall at a very low cost.
The problem is that extent_write_cache_pages could ignore
the new higher nr_to_write if nr_to_write had already gone
down to zero. We fix that by rechecking the nr_to_write
for every page that is processed in the pagevec.
This updates the math around bumping the nr_to_write value
to make sure we don't leave a tiny amount of IO hanging
around for the very end of a new extent.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Now that the last users of markers have migrated to the event
tracer we can kill off the (now orphan) support code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <20090917173527.GA1699@lst.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Arjan complained about the suckyness of TSC on modern machines, and
asked if we could do something about that for PERF_SAMPLE_TIME.
Make cpu_clock() NMI safe by removing the spinlock and using
cmpxchg. This also makes it smaller and more robust.
Affects architectures that use HAVE_UNSTABLE_SCHED_CLOCK, i.e. IA64
and x86.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
/me dons the brown paper bag.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Draining the BTS buffer on a buffer overflow interrupt takes too
long resulting in a kernel lockup when tracing the kernel.
Restructure perf_counter sampling into sample creation and sample
output.
Prepare a single reference sample for BTS sampling and update the
from and to address fields when draining the BTS buffer. Drain the
entire BTS buffer between a single perf_output_begin() /
perf_output_end() pair.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090915130023.A16204@sedona.ch.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (64 commits)
ext4: Update documentation about quota mount options
ext4: replace MAX_DEFRAG_SIZE with EXT_MAX_BLOCK
ext4: Fix the alloc on close after a truncate hueristic
ext4: Add a tracepoint for ext4_alloc_da_blocks()
ext4: store EXT4_EXT_MIGRATE in i_state instead of i_flags
ext4: limit block allocations for indirect-block files to < 2^32
ext4: Fix different block exchange issue in EXT4_IOC_MOVE_EXT
ext4: Add null extent check to ext_get_path
ext4: Replace BUG_ON() with ext4_error() in move_extents.c
ext4: Replace get_ext_path macro with an inline funciton
ext4: Fix include/trace/events/ext4.h to work with Systemtap
ext4: Fix initalization of s_flex_groups
ext4: Always set dx_node's fake_dirent explicitly.
ext4: Fix async commit mode to be safe by using a barrier
ext4: Don't update superblock write time when filesystem is read-only
ext4: Clarify the locking details in mballoc
ext4: check for need init flag in ext4_mb_load_buddy
ext4: move ext4_mb_init_group() function earlier in the mballoc.c
ext4: Make non-journal fsync work properly
ext4: Assure that metadata blocks are written during fsync in no journal mode
...
Remove net/genetlink.h inclusion, now sched.c won't be recompiled
because of some networking changes.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow the short description after symbol name and dash in a kernel-doc
comment to span multiple lines, e.g. like this:
/**
* unmap_mapping_range - unmap the portion of all mmaps in the
* specified address_space corresponding to the specified
* page range in the underlying file.
* @mapping: the address space containing mmaps to be unmapped.
* ...
*/
The short description ends with a parameter description, an empty line
or the end of the comment block.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'current' is a pointer, so the right form is 'down_write(¤t->mm->mmap_sem)'.
Signed-off-by: Jianjun Kong <jianjun@zeuux.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kref_put() already occurs after the out label
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] sizeof cleanup
[WATCHDOG] wdt_pci: fix printk and variable type
[WATCHDOG] wdt_pci - use pci_request_region
[WATCHDOG] ar7_wdt: Fix error handling during probe.
[WATCHDOG] ar7_wdt: convert to become a platform driver
[WATCHDOG] fix book E watchdog to take WDIOC_SETTIMEOUT arg in seconds
[WATCHDOG] davinci: use clock framework for timer frequency
[WATCHDOG] Use DIV_ROUND_UP() macro in the coh901327 WDT
[WATCHDOG] Add support for WM831x watchdog
[WATCHDOG] Add watchdog driver for NUC900
[WATCHDOG] add SBC-FITPC2 watchdog driver
* 'for-linus' of git://gitserver.sunplusct.com/linux-2.6-score: (22 commits)
score: add TIF_NOTIFY_RESUME define in asm/thread_info.h
score: make init_thread_union align to THREAD_SIZE
score: update files according to review comments.
score: add old syscall support
score: add MEMORY_START and MEMORY_SIZE define, to make the code clear
score: update inconsistent declare after .c was changed
score: remove unused code, add include files in .c
score: clean up mm/init.c
score: make irq.h definitions local
score: cleanups: dead code, 0 as pointer, shadowed variables
score: fix function prototypes
score: add address space annotations
score: add missing #includes
score: move save arg5 and arg6 instruction in front of enable_irq
score: add prototypes for wrapped syscalls
score: remove init_mm
score: add generic sys_call_table
score: remove __{put,get}_user_unknown
score: unset __ARCH_WANT_IPC_PARSE_VERSION
score: update files according to review comments
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (262 commits)
sh: mach-ecovec24: Add user debug switch support
sh: Kill off unused se_skipped in alignment trap notification code.
sh: Wire up HAVE_SYSCALL_TRACEPOINTS.
video: sh_mobile_lcdcfb: use both register sets for display panning
video: sh_mobile_lcdcfb: implement display panning
sh: Fix up sh7705 flush_dcache_page() build.
sh: kfr2r09: document the PLL/FLL <-> RF relationship.
sh: mach-ecovec24: need asm/clock.h.
sh: mach-ecovec24: deassert usb irq on boot.
sh: Add KEYSC support for EcoVec24
sh: add kycr2_delay for sh_keysc
sh: cpufreq: Include CPU id in info messages.
sh: multi-evt support for SH-X3 proto CPU.
sh: clkfwk: remove bogus set_bus_parent() from SH7709.
sh: Fix the indication point of the liquid crystal of AP-325RXA(AP3300)
sh: Add EcoVec24 romImage defconfig
sh: USB disable process is needed if romImage boot for EcoVec24
sh: EcoVec24: add HIZA setting for LED
sh: EcoVec24: write MAC address in boot
sh: Add romImage support for EcoVec24
...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Clean up linker script using standard macros.
[IA64] Use standard macros for page-aligned data.
[IA64] Use .ref.text, not .text.init for start_ap.
[IA64] sgi-xp: fix printk format warnings
[IA64] ioc4_serial: fix printk format warnings
[IA64] mbcs: fix printk format warnings
[IA64] pci_br, fix infinite loop in find_free_ate()
[IA64] kdump: Short path to freeze CPUs
[IA64] kdump: Try INIT regardless of
[IA64] kdump: Mask INIT first in panic-kdump path
[IA64] kdump: Don't return APs to SAL from kdump
[IA64] kexec: Unregister MCA handler before kexec
[IA64] kexec: Make INIT safe while transition to
[IA64] kdump: Mask MCA/INIT on frozen cpus
Fix up conflict in arch/ia64/kernel/vmlinux.lds.S as per Tony's
suggestion.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: add fusectl interface to max_background
fuse: limit user-specified values of max background requests
fuse: use drop_nlink() instead of direct nlink manipulation
fuse: document protocol version negotiation
fuse: make the number of max background requests and congestion threshold tunable
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (62 commits)
DaVinci: DM646x - platform changes for vpif capture and display drivers
davinci: DM355 - platform changes for vpfe capture
davinci: DM644x platform changes for vpfe capture
davinci: audio: move tlv320aic33 i2c setup into board files
DaVinci: EDMA: Adding 2 new APIs for allocating/freeing PARAMs
DaVinci: DM365: Adding entries for DM365 IRQ's
DaVinci: DM355: Adding PINMUX entries for DM355 Display
davinci: Handle pinmux conflict between mmc/sd and nor flash
davinci: Add NOR flash support for da850/omap-l138
davinci: Add NAND flash support for DA850/OMAP-L138
davinci: Add MMC/SD support for da850/omap-l138
davinci: Add platform support for da850/omap-l138 GLCD
davinci: Macro to convert GPIO signal to GPIO pin number
davinci: Audio support for DA850/OMAP-L138 EVM
davinci: Audio support for DA830 EVM
davinci: Correct the number of GPIO pins for da850/omap-l138
davinci: Configure MDIO pins for EMAC
DaVinci: DM365: Add Support for new Revision of silicon
DaVinci: DM365: Fix Compilation issue due to PINMUX entry
DaVinci: EDMA: Updating default queue handling
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: use kernel_sendpage
dlm: fix connection close handling
dlm: fix double-release of socket in error exit path
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
ext3: Flush disk caches on fsync when needed
ext3: Add locking to ext3_do_update_inode
ext3: Fix possible deadlock between ext3_truncate() and ext3_get_blocks()
jbd: Annotate transaction start also for journal_restart()
jbd: Journal block numbers can ever be only 32-bit use unsigned int for them
ext3: Update MAINTAINERS for ext3 and JBD
JBD: round commit timer up to avoid uncommitted transaction
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix NULL ptr regression in powernow-k8
[CPUFREQ] Create a blacklist for processors that should not load the acpi-cpufreq module.
[CPUFREQ] Powernow-k8: Enable more than 2 low P-states
[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call (second call site)
[CPUFREQ] ondemand - Use global sysfs dir for tuning settings
[CPUFREQ] Introduce global, not per core: /sys/devices/system/cpu/cpufreq
[CPUFREQ] Bail out of cpufreq_add_dev if the link for a managed CPU got created
[CPUFREQ] Factor out policy setting from cpufreq_add_dev
[CPUFREQ] Factor out interface creation from cpufreq_add_dev
[CPUFREQ] Factor out symlink creation from cpufreq_add_dev
[CPUFREQ] cleanup up -ENOMEM handling in cpufreq_add_dev
[CPUFREQ] Reduce scope of cpu_sys_dev in cpufreq_add_dev
[CPUFREQ] update Doc for cpuinfo_cur_freq and scaling_cur_freq
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (34 commits)
time: Prevent 32 bit overflow with set_normalized_timespec()
clocksource: Delay clocksource down rating to late boot
clocksource: clocksource_select must be called with mutex locked
clocksource: Resolve cpu hotplug dead lock with TSC unstable, fix crash
timers: Drop a function prototype
clocksource: Resolve cpu hotplug dead lock with TSC unstable
timer.c: Fix S/390 comments
timekeeping: Fix invalid getboottime() value
timekeeping: Fix up read_persistent_clock() breakage on sh
timekeeping: Increase granularity of read_persistent_clock(), build fix
time: Introduce CLOCK_REALTIME_COARSE
x86: Do not unregister PIT clocksource on PIT oneshot setup/shutdown
clocksource: Avoid clocksource watchdog circular locking dependency
clocksource: Protect the watchdog rating changes with clocksource_mutex
clocksource: Call clocksource_change_rating() outside of watchdog_lock
timekeeping: Introduce read_boot_clock
timekeeping: Increase granularity of read_persistent_clock()
timekeeping: Update clocksource with stop_machine
timekeeping: Add timekeeper read_clock helper functions
timekeeping: Move NTP adjusted clock multiplier to struct timekeeper
...
Fix trivial conflict due to MIPS lemote -> loongson renaming.
The early initialization of the pci bus to node mapping leaves all busses
with a node id of -1 if it lacks memory affinity. Thus, cpumask_of_pcibus
must return all online cpus for such busses.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Using list_del_init is generally safer than list_del, and it will
allow us, in a subsequent patch, to see if an entry has already been
processed or not.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
McASP register settings are not correct for DSP mode of operation.
There is a channel swap initally. This patch provides fixes to
the register values for proper working.
Tested on DA830/OMAP-L137 EVM, DM6467 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the sound system hasn't been utilized yet and we suspend, then we
attempt to save/restore using state that doesn't exist. So use a global
handle instead to reconfigure properly.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit ac89a9174 ("pty: don't limit the writes to 'pty_space()' inside
'pty_write()'") removed the pty_space() checking, in order to let the
regular tty buffer code limit the buffering itself.
That was all good, but as a subtle side effect it meant that we'd be
doing a tty_wakeup() even in the case where the buffers were all filled
up, and didn't actually make any progress on the write.
Which sounds innocuous, but it interacts very badly with the ppp_async
code, which has an infinite loop in ppp_async_push() that tries to push
out data to the tty. When we call tty_wakeup(), that loop ends up
thinking that progress was made (see the subtle interactions between
XMIT_WAKEUP and 'tty_stuffed' for details). End result: one unhappy ppp
user.
Fixed by noticing when tty_insert_flip_string() didn't actually do
anything, and then not doing any more processing (including, very much
not calling tty_wakeup()).
Bisected-and-tested-by: Peter Volkov <pva@gentoo.org>
Cc: stable@kernel.org (2.6.31)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
UV depends on the MMRHI space being identity mapped. The patch:
x86: Make 64-bit efi_ioremap use ioremap on MMIO regions
changed this to make efi regions at a different address using
ioremap. Add the identity mapping to uv_system_init.
( Note this code was previously present but was deleted when BIOS
added the ranges to the EFI map - previous efi code identify
mapped the ranges. )
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090909154339.GA7946@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add volatile-semantics to the SGI UV read/write macros that are
used to access chipset memory mapped registers. No direct
references to volatile are made. Instead the readq/writeq macros
are used.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
Cc: dwalker@fifo99.com
Cc: cfriesen@nortel.com
LKML-Reference: <20090910143149.GA14273@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The UV BIOS has changed the way interrupt remapping is being done.
This affects the id used for sending IPIs. The upper id bits no
longer need to be masked off.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: <stable@kernel.org>
LKML-Reference: <20090909154104.GA25083@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This was done using Coccinelle's BUG_ON semantic patch.
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Cc: Julia Lawall <julia@diku.dk>
LKML-Reference: <1252777220-30796-1-git-send-email-dwalker@fifo99.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix printk format warning:
drivers/watchdog/wdt_pci.c:652: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'resource_size_t'
and then use resource_size_t for the "io" variable as well
so that it won't be truncated.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch converts the ar7_wdt driver to become
a platform driver. The AR7 SoC specific identification
and base register calculation is performed by the board
code, therefore we no longer need to have access to
ar7_chip_id. We also remove the reboot notifier code to
use the platform shutdown method as Wim suggested.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WDIOC_SETTIMEOUT argument is supposed to be a "seconds" value.
However, the book E wdt currently treats it as a "period" which is
interpreted in a board-specific way.
This patch allows the user to pass in a "seconds" value and the driver
will set the smallest timeout that is at least as large as specified
by the user. It's been tested on e500 hardware and works as
expected.
The patch only modifies the CONFIG_FSL_BOOKE case, the CONFIG_4xx case
is left unmodified as I don't have any hardware to test it on.
Signed-off-by: Chris Friesen <cfriesen@nortel.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove use of CLOCK_TICK_RATE in favor of using clock framework
for getting timer frequency.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
