Currently 'ifconfig' for the Ethernet devices handled by this driver shows
"DMA chan: ff" while the driver doesn't use any DMA channels. Not assigning
a value to 'net_device::dma' causes 'ifconfig' to correctly not report a
DMA channel.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately warnings generated after parsing in sphinx can end up
with entirely bogus files and line numbers as sources. Strangely for
outright errors this is not a problem. Trying to convert warnings to
errors also doesn't fix it.
The only way to get useful output out of sphinx to be able to root
cause the error seems to be enabling keep_warnings, which inserts
a System Message into the actual output. Not pretty at all, but I
don't really want to fix up core rst/sphinx code, and this gets the job
done meanwhile.
Cc: Markus Heiser <markus.heiser@darmarit.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
We should only "put" the interface if submitting URB or setting tablet mode
in pegasus_open() fails, otherwise leave it to pegasus_close().
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch allows to simulate the lost of frames exchanged between the 2
nfcsim devices through a control entry in the debugfs and is used as
follow:
echo n > /sys/kernel/debug/nfcsim/nfcX/dropframe
Where n specifies the number of frames to be dropped between 0 and 255
and nfcX is either nfc0 or nfc1, one of the two nfcsim devices.
In the following example, the next frame that should be sent by the nfc0
device will be dropped and thus not received by the nfc1 device:
echo 1 > /sys/kernel/debug/nfcsim/nfc0/dropframe
The value of 0 can be used to reset the dropframe counter.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The idea is to have a way to control and/or modify the behavior of the
nfcsim virtual devices.
This patch creates a folder tree in the debug filesystem. The debugfs is
usually mounted into /sys/kernel/debug and the nfcsim entries are
located in DEBUGFS/nfcsim/nfcX/ where X is either 0 or 1 depending on
the device you want to address.
These folders are empty for now and control entries will be added by
upcoming commits.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Commit 4995734e97 "acpi, nfit: fix acpi_check_dsm() vs zero functions
implemented" attempted to fix a QEMU regression by supporting its usage
of a zero-mask as a valid response to a DSM-family probe request.
However, this behavior breaks HP platforms that return a zero-mask by
default causing the probe to misidentify the DSM-family.
Instead, the QEMU regression can be fixed by simply not requiring the DSM
family to be identified.
This effectively reverts commit 4995734e97, and removes the DSM
requirement from the init path.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: Linda Knippers <linda.knippers@hpe.com>
Fixes: 4995734e97 ("acpi, nfit: fix acpi_check_dsm() vs zero functions implemented")
Reported-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Tested-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
input_mt_init_slots() may fail and we should be handling failures properly.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tejun Heo <tj@kernel.org>
In 'get_scq', 'dma_alloc_coherent' has been used to allocate some
resources, so we need to free them using 'dma_free_coherent' instead
of 'kfree'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 'cpmac_open', 'dma_alloc_coherent' has been used to allocate some
resources, so we need to free them using 'dma_free_coherent' instead
of 'kfree'.
Also, we don't need to free these resources if the allocation has failed.
So I have slighly modified the goto label in this case.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.8. Major changes:
ath9k
* implement temperature compensation support for AR9003+
ath10k
* disable wake_tx_queue() mac80211 op for older devices to workaround
throughput regression
For rtl8188ee, we pass -Idrivers/net/wireless/rtlwifi/ to gcc,
however that directy no longer exists, so evidently this option
is no longer required here and can be removed to avoid a warning
when building with 'make W=1' or 'gcc -Wmissing-include-dirs'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We dropped strict MIPS dependency for bcm47xxsflash driver in:
commit 5651d6aaf4 ("mtd: bcm47xxsflash: use ioremap_cache() instead of
KSEG0ADDR()") but using ioremap_cache still limits building it to few
selected architectures only.
A recent commit 57d8f7dd21 ("bcma: allow enabling serial flash support
on non-MIPS SoCs") automatically dropped MIPS dependency for
MTD_BCM47XXSFLASH which broke building e.g. on powerpc and cris.
The bcma change is alright as it doesn't break building bcma code in any
way. MTD_BCM47XXSFLASH on the other hand should be limited to archs
which need it and can build it (by providing ioremap_cache).
Fixes: 57d8f7dd21 ("bcma: allow enabling serial flash support on non-MIPS SoCs")
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for using with both wl12xx and wl18xx.
- all wilink family needs special init command for entering wspi mode.
extra clock cycles should be sent after the spi init command while the
cs pin is high.
- Use inverted chip select for sending a dummy 4 bytes command that
completes the init stage.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wlc_phy_txpower_get_current() does a logical OR of power->flags, which
presumes that power.flags was initiliazed earlier by the caller,
unfortunately, this is not the case, so make sure we zero out the struct
tx_power before calling into wlc_phy_txpower_get_current().
Reported-by: coverity (CID 146011)
Fixes: 5b435de0d7 ("net: wireless: add brcm80211 drivers")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case dma_mapping_error() returns an error in dma_rxfill, we would be
leaking a packet that we allocated with brcmu_pkt_buf_get_skb().
Reported-by: coverity (CID 1081819)
Fixes: 67d0cf50bd ("brcmsmac: Fix WARNING caused by lack of calls to dma_mapping_error()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case brcmf_sdiod_recv_chain() cannot complete a succeful call to
brcmf_sdiod_buffrw, we would be leaking glom_skb and not free it as we
should, fix this.
Reported-by: coverity (CID 1164856)
Fixes: a413e39a38 ("brcmfmac: fix brcmf_sdcard_recv_chain() for host without sg support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We don't have access to datasheets to document all the bits but we can
name these registers at least.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reduce indentation, use a variable to save a few pointer dereferences
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AR_PHY_65NM_CH0_THERM and AR_CH0_THERM were supposed to refer to the
same register, however they had different SREV checks.
Remove the duplicate and use the checks. Since there were other SREV
checks present in the only place that uses this, this will probaby not
affect runtime behavior.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The register layout of AR_PHY_SPECTRAL_SCAN has changed, only AR9280
uses the old layout
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There were two paths in the code for "external" eeprom sources. The code
in eeprom.c only handled the cases where the eeprom data was loaded via
request_firmware. ahb.c and pci.c on the other hand had some duplicate
code which was only used when the eeprom data was passed via
ath9k_platform_data.
With this change all eeprom data handling is now unified in eeprom.c.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When an NL80211_DISCONNECT is sent to cfg80211, the driver's cfg80211
disconnect function sets the sme_state to SME_DISCONNECTED before receiving
a WMI_DISCONNECT_EVENT from the firmware. This caused cfg80211 to not know
that the connection is disconnected because the driver fails to notify
cfg80211 upon receiving WMI_DISCONNECT_EVENT from the firmware believing
it is already disconnected.
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We only get nf_connlabels if the user add ct label set expr successfully,
but we will also put nf_connlabels if the user delete ct lable get expr.
This is mismathced, and will cause ct label expr cannot work properly.
Also, if we init something fail, we should put nf_connlabels back.
Otherwise, we may waste to alloc the memory that will never be used.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Update and expand the CEC documentation. Especially w.r.t. non-blocking
mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Even when the adapter is configured for CEC 1.4, we still check and
use the CEC 2.0 parts of struct cec_log_addrs. Although these aren't
used in CEC messages, the information contained in them is still of
use in the CEC framework itself, so keep this information.
Also zero the unused trailing features[] data and unused logical address
data so the contents isn't random data.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For POLLOUT poll only checked if the adapter was configured, not
if there was room in the transmit queue. Add that check.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Just pass the transmitted CEC message to all CEC adapters.
This implements the Monitor All mode for vivid.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The main message loop checks if the physical address was valid, and if
not it is assumed that the adapter had been unconfigured.
However, this check is no longer correct, instead it should check
that both adap->is_configured and adap->is_configuring are false.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The size of the transmit queue was unlimited, which meant that
in non-blocking mode you could flood the CEC adapter with messages
to be transmitted.
Limit this to 18 messages.
Also print the number of pending transmits and the timeout value
in the status debugfs file.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Ensure that the unused part of the msg array is zeroed. This is
required by CEC 2.0 when receiving shorter messages than expected.
In that case the remaining bytes are assumed to be 0.
There are no such CEC messages yet, but it is required to be future proof.
And since we're doing it for received messages, do it for transmitted
messages as well. It's unambiguous this way.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The filehandle was set to NULL when in non-blocking mode or when
no reply is needed.
This is wrong: the filehandle is needed in non-blocking mode to ensure
that the result of the transmit can be obtained through CEC_RECEIVE.
And the 'reply' check was also incorrect since it should have checked the
timeout field (the reply can be 0). In any case, when in blocking mode
there is no need to set the fh to NULL either.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Before transmitting a message clear all status fields and always fill
in the sequence number. Make sure the sequence number is never 0.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When CEC_RECEIVE returns a message the original timeout field
was overwritten. Restore the timeout field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Stepping with PSTATE.D=1 is bad news. The step won't generate a debug
exception and we'll likely walk off into random data structures. This
should never happen, but when it does, it's a PITA to debug. Add a
WARN_ON to shout if we realise this is about to take place.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The debug enable/disable macros are not used anywhere in the kernel, so
remove them from irqflags.h
Reported-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There is no need to explicitly clear the SS bit immediately before
setting it unconditionally.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Clearing PSTATE.D is one of the requirements for generating a debug
exception. The arm64 booting protocol requires that PSTATE.D is set,
since many of the debug registers (for example, the hw_breakpoint
registers) are UNKNOWN out of reset and could potentially generate
spurious, fatal debug exceptions in early boot code if PSTATE.D was
clear. Once the debug registers have been safely initialised, PSTATE.D
is cleared, however this is currently broken for two reasons:
(1) The boot CPU clears PSTATE.D in a postcore_initcall and secondary
CPUs clear PSTATE.D in secondary_start_kernel. Since the initcall
runs after SMP (and the scheduler) have been initialised, there is
no guarantee that it is actually running on the boot CPU. In this
case, the boot CPU is left with PSTATE.D set and is not capable of
generating debug exceptions.
(2) In a preemptible kernel, we may explicitly schedule on the IRQ
return path to EL1. If an IRQ occurs with PSTATE.D set in the idle
thread, then we may schedule the kthread_init thread, run the
postcore_initcall to clear PSTATE.D and then context switch back
to the idle thread before returning from the IRQ. The exception
return path will then restore PSTATE.D from the stack, and set it
again.
This patch fixes the problem by moving the clearing of PSTATE.D earlier
to proc.S. This has the desirable effect of clearing it in one place for
all CPUs, long before we have to worry about the scheduler or any
exception handling. We ensure that the previous reset of MDSCR_EL1 has
completed before unmasking the exception, so that any spurious
exceptions resulting from UNKNOWN debug registers are not generated.
Without this patch applied, the kprobes selftests have been seen to fail
under KVM, where we end up attempting to step the OOL instruction buffer
with PSTATE.D set and therefore fail to complete the step.
Cc: <stable@vger.kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
raid_io_hints() was retrieving the number of data stripes used for the
calculation of io_opt from struct r5conf, which is not defined for raid0
mappings.
Base the calculation on the in-core raid_set structure instead.
Also, adjust to use to_bytes() for the sector -> bytes conversion
throughout.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use 'unsigned int' where appropriate.
Return negative errors.
Correct an indentation.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
