For some platforms it's definitions may conflict. So that's the one-liner.
The rest is 10 square kilometers of collateral damage fixup this include
used to paper over.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current ppc64_defconfig kernel fails to boot on iSeries, dying with:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc00000000071b258
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=32 iSeries
<snip>
NIP [c00000000071b258] .iSeries_src_init+0x34/0x64
LR [c000000000701bb4] .kernel_init+0x1fc/0x3bc
Call Trace:
[c000000007d0be30] [0000000000008000] 0x8000 (unreliable)
[c000000007d0bea0] [c000000000701bb4] .kernel_init+0x1fc/0x3bc
[c000000007d0bf90] [c0000000000262d4] .kernel_thread+0x4c/0x68
Instruction dump:
e922cba8 3880ffff 78840420 f8010010 f821ff91 60000000 e8090000 78095fe3
4182002c e922cb58 e862cbb0 e9290140 <e8090000> f8410028 7c0903a6 e9690010
Kernel panic - not syncing: Attempted to kill init!
This happens because some powermac code unconditionally sets
ppc_md.progress to NULL. This patch makes sure the powermac late
initcall is only run on powermac machines.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The "is_exec" branch of the protection check in do_page_fault()
didn't do anything on 32-bit PowerPC. So if a userland program
jumps to a page with Linux protection flags "---p", all the tests
happily fall through, and handle_mm_fault() is called, which in
turn calls handle_pte_fault(), which calls update_mmu_cache(),
which goes flush the dcache to a page with no access rights.
Boom.
This fixes it.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to know the CPU ID in order to calculate the mask and ack
registers effectively. Stub this in for UP.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was using CONFIG_SH_SOLUTION_ENGINE, where we really wanted
CONFIG_SOLUTION_ENGINE. While we're at it, move the whole CF
enabler mess somewhere better suited.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The patch adds fragments caused by rh_alloc_align() back to free list, instead
of allocating the whole chunk of memory. This will greatly improve memory
utilization managed by rheap.
It solves MURAM not enough problem with 3 UCCs enabled on MPC8323.
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is mainly to switch off all potentially debugging stuff that
won't report anything useful after an oops happened.
Besided that setting pause_on_oops will work too, but doesn't make
too much sense on s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Print list of modules on die() like a lot of other architectures do.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When appending the 'cio_ignore' kernel parameter to the command line, a blank
has to be inserted in order to separate 'cio_ignore' from the preceding kernel
parameters.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current implementation only handles -ERESTARTNOHAND, whereas we
also need to handle -ERESTART_RESTARTBLOCK in the handle_signal()
case for restartable system calls. Follows the sh change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The current implementation only handles -ERESTARTNOHAND, whereas we
also need to handle -ERESTART_RESTARTBLOCK in the handle_signal()
case for restartable system calls.
As noted by Carl:
This fixes the LTP test nanosleep03 - the current kernel causes
-ERESTART_RESTARTBLOCK to reach user space rather than the correct
-EINTR.
Reported-by: Carl Shaw <shaw.carl@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add the kernel release and version information to the output of
show_regs/oops. Add the CPU PSR register. Avoid using printk
to output partial lines; always output a complete line.
Re-combine the "Control" and "Table + DAC" lines after nommu
separated them; we don't want to waste vertical screen space
needlessly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only print out pgd/pte data in the oops path if oops_may_print()
holds true. Follows the i386 implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As Russell helpfully pointed out on linux-arch:
http://marc.info/?l=linux-arch&m=118208089204630&w=2
We were missing the oops_enter/exit() in the sh die() implementation.
As we do support lockdep, it's beneficial to add these calls so lockdep
properly disables itself in the die() case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We use R0 as the 5th argument of syscall. When the syscall restarts
after signal handling, we should restore the old value of R0.
The attached patch does it. Without this patch, I've experienced random
failures in the situation which signals are issued frequently.
Signed-off-by: Kaz Kojima <kkojima@rr.iij4u.or.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add calls to oops_enter() and oops_exit() to __die(), so that
things like lockdep know when an oops occurs.
Add suffixes to the oops report to indicate whether the running
kernel has been built with preempt or smp support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Distros seem to be removing PAGE_SIZE from asm/page.h. So, the libc side of
UML should stop using it.
I replace it with UM_KERN_PAGE_SIZE, which is defined to be the same as
PAGE_SIZE on the kernel side of the house. I could also use getpagesize(),
but it's more important that UML have the same value of PAGE_SIZE everywhere.
It's conceivable that it could be built with a larger PAGE_SIZE, and use of
getpagesize() would break that badly.
PAGE_MASK got the same treatment, as it is closely tied to PAGE_SIZE.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix oops triggered during: echo 0 > /proc/sys/kernel/nmi_watchdog
The culprit seems to be 09198e6850:
[PATCH] i386: Clean up NMI watchdog code
In two places, the parameters to release_{evntsel,perfctr}_nmi
got interchanged during the cleanup.
Fix interchanged parameters to release_{evntsel,perfctr}_nmi.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When disabled through /proc/sys/kernel/nmi_watchdog, the NMI watchdog uses the
stop() method directly, which does not decrement the activity counter, leading
to a BUG(). Use the wrapper function instead to fix that.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At system boot time, the NMI watchdog no longer reserved its MSRs, allowing
other subsystems to mess with them. Fix that.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (30 commits)
Blackfin SMC91X ethernet supporting driver: SMC91C111 LEDs are note drived in the kernel like in uboot
Blackfin SPI driver: fix bug SPI DMA incomplete transmission
Blackfin SPI driver: tweak spi cleanup function to match newer kernel changes
Blackfin RTC drivers: update MAINTAINERS information
Blackfin serial driver: decouple PARODD and CMSPAR checking from PARENB
Blackfin serial driver: actually implement the break_ctl() function
Blackfin serial driver: ignore framing and parity errors
Blackfin serial driver: hook up our UARTs STP bit with userspaces CMSPAR
Blackfin arch: move HI/LO macros into blackfin.h and punt the rest of macros.h as it includes VDSP macros we never use
Blackfin arch: redo our linker script a bit
Blackfin arch: make sure we initialize our L1 Data B section properly based on the linked kernel
Blackfin arch: fix bug can not wakeup from sleep via push buttons
Blackfin arch: add support for Alon Bar-Lev's dynamic kernel command-line
Blackfin arch: add missing gpio.h header to fix compiling in some pm configurations
Blackfin arch: As Mike pointed out range goes form m..MAX_BLACKFIN_GPIO -1
Blackfin arch: fix spelling typo in output
Blackfin arch: try to split up functions like this into smaller units according to LKML review
Blackfin arch: add proper ENDPROC()
Blackfin arch: move more of our startup code to .init so it can be freed once we are up and running
Blackfin arch: unify differences between our diff head.S files -- no functional changes
...
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix builds where MSC01E_xxx is undefined.
[MIPS] Separate performance counter interrupts
[MIPS] Malta: Fix for SOCitSC based Maltas
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
[AVR32] Define ARCH_KMALLOC_MINALIGN to L1_CACHE_BYTES
[AVR32] STK1000: Set SPI_MODE_3 in the ltv350qv board info
[AVR32] gpio_*_cansleep() fix
[AVR32] ratelimit segfault reporting rate
This patch reworks the ipr code by grouping the offset array together
with the ipr_data structure in a new data structure called ipr_desc.
This new structure also contains the name of the controller in struct
irq_chip. The idea behind putting struct irq_chip in there is that we
can use offsetof() to locate the base addresses in the irq_chip
callbacks. This strategy has much in common with the recently merged
intc2 code.
One logic change has been made - the original ipr code enabled the
interrupts by default but with this patch they are all disabled by
default.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We don't have a PMB for SH-X2 or later, so only enable it for
the few CPUs that support it. Fixes up the boot for SH4AL-DSP.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The shared intc2 code currently contains cpu-specific #ifdefs.
This is a tad unclean and it prevents us from using the shared code
to drive board-specific irqs on the se7780 board.
This patch reworks the intc2 code by moving the base addresses of
the intc2 registers into struct intc2_desc. This new structure also
contains the name of the controller in struct irq_chip. The idea
behind putting struct irq_chip in there is that we can use offsetof()
to locate the base addresses in the irq_chip callbacks.
One logic change has been made - the original shared intc2 code
enabled the interrupts by default but with this patch they are all
disabled by default.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (30 commits)
[PARISC] remove global_ack_eiem
[PARISC] Fix kernel panic in check_ivt
[PARISC] Fix bug when syscall nr is __NR_Linux_syscalls
[PARISC] be more defensive in process.c::get_wchan
[PARISC] fix "reduce size of task_struct on 64-bit machines" fallout
[PARISC] fix null ptr deref in unwind.c
[PARISC] fix trivial spelling nit in asm/linkage.h
[PARISC] remove remnants of parisc-specific softirq code
[PARISC] fix section mismatch in smp.c
[PARISC] fix "ENTRY" macro redefinition
[PARISC] Wire up utimensat/signalfd/timerfd/eventfd syscalls
[PARISC] fix section mismatch in superio serial drivers
[PARISC] fix section mismatch in parisc eisa driver
[PARISC] fix section mismatches in arch/parisc/kernel
[PARISC] fix section mismatch in ccio-dma
[PARISC] fix section mismatch in parisc STI video drivers
[PARISC] fix section mismatch in parport_gsc
[PARISC] fix lasi_82596 build
[PARISC] Build fixes for power.c
[PARISC] kobject is embedded in subsys, not kset
...
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix args to sun4v_ldc_revoke().
[SPARC64]: Really fix parport.
[SPARC64]: Fix IO/MEM space sizing for PCI.
[SPARC64]: Wire up cookie based sun4v interrupt registry.
Support for performance counter overflow interrupt that is on a separate
interrupt from the timer.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
And an attempt to tidy up the core/controller differences.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the latest incarnation of the ltv350qv driver the call to
spi_setup() has been removed. So we need to initialize things more
carefully in the board info struct.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Limit the rate of the kernel logging for the segfaults of user
applications, to avoid potential message floods or denial-of-service
attacks.
Signed-off-by: Andrea Righi <a.righi@cineca.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This fixes some problems with the way the some things
represented in the device tree for the Holly and Taiga boards. This
means changes both to the dts files, and to the code which
instantiates the tsi108 ethernet platform devices based on the device
tree.
- First, and most importantly, the ethernet PHYs are given
with an identical 'reg' property. This reg currently encodes the
accessible register used to initiate mdio interaction with the PHYs,
rather than a meaningful address on the parent bus (mdio in this
case), which is incorrect. Instead we give the address of these
registers as 'reg' in the mdio node itself, and encode the ID of each
phy in their 'reg' propertyies.
- Currently the platform device constructor enables a
workaround in the tsi108 ethernet driver based on the compatible
property of the PHY. This is incorrect, because the workaround in
question is necessary due to the board's wiring of the PHY, not the
model of PHY itself. This patch alters the constructor to instead
enable the workaround based on a new special property in the PHY node.
- The compatible properties on a number of nodes in the device
tree are insufficiently precise. In particular the PHYs give only
"bcm54xx", which is broken, since there are many bcm54xx PHY models,
and they have differences which matter. The mdio had a compatible
property of "tsi-ethernet" identical to the ethernet MAC nodes, which
doesn't make sense. The ethernet, i2c, bridge and PCI nodes were
given only as "tsi-*" which is somewhat inprecise, we replace with
"tsi108-*" in the case of Taiga (which has a TSI108 bridge), and
"tsi109-*", "tsi108-*" in the case of Holly (which has a TSI109
bridge).
- We remove some "model" properties from the ethernets on
Taiga board which were neither useful nor adequately precise.
- On Holly we change to using a dtc label instead of a full
path to reference the MPIC node, which makes the dts a little more
readable.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the Holly device tree includes a bootargs property in
/chosen, which gives a commandline. This is somewhat inconvenient,
because it means an alternative default command line can't be given in
the kernel config - the value obtained from the dts via the
bootwrapper will always override CONFIG_CMDLINE.
This removes the command line from the dts, and instead puts the
same command line as a default in holly_defconfig.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The various cuboot platforms (i.e. pre-device tree aware u-boot for
83xx, 85xx and Ebony) share a certain amount of code for parsing the
boot parameters. To a certain extent that's inevitable, since they
platforms have different definitions of the bd_t structure. However,
with some macro work and a helper function, this patch improves the
situation a bit.
In the process, this fixes a bug on Ebony, which was incorrectly
handling the parameters passed form u-boot for the command line (the
bug was copied from 83xx and 85xx which have subsequently been fixed).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the device tree for Ebony, the 'ranges' property in the node for
the EBC bridge shows the mappings from the chip select / address lines
actually used for the EBC peripherals into the address space of the
OPB. At present, these mappings are hardcoded in ebony.dts for the
mappings set up by the OpenBIOS firmware when it configures the EBC
bridge.
This replaces the hardcoded mappings with code in the zImage to
read the EBC configuration registers and create an appropriate ranges
property based on them. This should make the zImage and kernel more
robust to changes in firmware configuration. In particular, some of
the Ebony's DIP switches can change the effective address of the Flash
and other peripherals in OPB space. With this patch, the kernel will
be able to cope with at least some of the possible variations.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ebony_exit() function which resets the Ebony board should in fact
be common to most if not all 44x boards. This moves the function out
into 44x.c, renaming it, so it can be used by other 44x platforms.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the powerpc kernel has a 64-bit only feature,
COHERENT_ICACHE used for those CPUS which maintain icache/dcache
coherency in hardware (POWER5, essentially). It also has a feature,
SPLIT_ID_CACHE, which is used on CPUs which have separate i and
d-caches, which is to say everything except 601 and Freescale E200.
In nearly all the places we check the SPLIT_ID_CACHE, what we actually
care about is whether the i and d-caches are coherent (which they will
be, trivially, if they're the same cache).
This tries to clarify the situation a little. The COHERENT_ICACHE
feature becomes availble on 32-bit and is set for all CPUs where i and
d-cache are effectively coherent, whether this is due to special logic
(POWER5) or because they're unified. We check this, instead of
SPLIT_ID_CACHE nearly everywhere.
The SPLIT_ID_CACHE feature itself is replaced by a UNIFIED_ID_CACHE
feature with reversed sense, set only on 601 and Freescale E200. In
the two places (one Freescale BookE specific) where we really care
whether it's a unified cache, not whether they're coherent, we check
this feature. The CPUs with unified cache are so few, we could
consider replacing this feature bit with explicit checks against the
PVR.
This will make unifying the 32-bit and 64-bit cache flush code a
little more straightforward.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Using typedefs to rename structure types if frowned on by CodingStyle.
However, we do so for the hash PTE structure on both ppc32 (where it's
called "PTE") and ppc64 (where it's called "hpte_t"). On ppc32 we
also have such a typedef for the BATs ("BAT").
This removes this unhelpful use of typedefs, in the process
bringing ppc32 and ppc64 closer together, by using the name "struct
hash_pte" in both cases.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In arch/powerpc/mm/pgtable_32.c, the variable io_bat_index and the
macro is_power_of_4() no longer have any users. This removes them.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
