Having generic hardware timer interrupt in debugfs
would come handy when we are debugging 3 WIRE
BTCOEX issues.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Read and configure thermometer calibration results read from
OTP card.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before disabling BTCOEX in the h/w cancel all BTCOEX related
works. This is similar to the commit in ath9k(c32cdbd8)
ath9k: Stop the BTCOEX timers before disabling BTCOEX
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable BTCOEX for WB193(which seems to be the only supported
ath9k_htc BTCOEX chipset)only when it is enabled via modparam,
rather than enabling it by default.
Cc: Vivek Natarajan <nataraja@qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
*Remove all the checks that will be handled by cfg80211
based on the interface combination advertised. For instance,
driver supports at the maximum 8 beaconing interface, while
we advertise maximum 8 beaconing interface in the interface
combination support.
*cfg80211 will take care of not allowing
us to add an interface that is not supported by the
driver, further if the change_interface changes the
old interface to a beaconing interface while we had
reached the max limit of 8 beaconing interface, again
cfg80211 takes care of this stuff!
So remove all these checks.
*Beautify placing PS wrappers in the appropriate
position.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Additionally it has a neat debug message informing us
that we are stopping the ANI algorithm.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Its more correct to convert btcoex_period to 'us' while
comparing with btcoex_no_stomp which is in 'us'.
Did not find any functionality issues being fixed,
as the generic hardware timer triggers are usually
refreshed with the newer duty cycle.
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a possibility that AR_MCI_GPM_1 register can
return 0xdeadbeef and this results in caching of invalid
GPM index in ar9003_mci_is_gpm_valid. Ensure we
have appropriate checks to avoid this.
Cc: xijin luo <xijin@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some checks for PA linearization support checked ATH9K_HW_CAP_PAPRD and some
used the EEPROM ops, leading to issues in tx power handling, since those
two can be out of sync.
Disable the feature by default, since it has been reported that it can
cause damage to the rx path under some circumstances. It can now be enabled
for testing via debugfs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark keys that might be used to receive management
frames so drivers can fall back on software crypto
for them if they don't support hardware offload.
As the new flag is only set correctly for RX keys
and the existing IEEE80211_KEY_FLAG_SW_MGMT flag
can only affect TX, also rename the latter to
IEEE80211_KEY_FLAG_SW_MGMT_TX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TX filter bit for a station would be set by the HW
when a frame is not acked. A frame would be completed with
ATH9K_TXERR_FILT status only when the corresponding filter bit
for the destination station is already set.
Currently, un-acknowledged packets are added to the pending queue
and retried, but the "clear_dest_mask" bit in the descriptor is
set only when the TX status has been ATH9K_TXERR_FILT. This results
in packet loss and the log shows:
wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746071
wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746076
wlan0: dropped TX filtered frame, queue_len=0 PS=0 @4309746377
...
...
This issue can be resolved by making sure that the destination
mask is cleared when the packet is being retried and the earlier
TX status is ATH9K_TXERR_XRETRY.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assign the MCI BT state locally, rather than unnecessarily calling
ar9003_mci_state and updating it.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not necessary to hold the firmware memory during the whole
driver lifetime, and obviously it does waste memory. Suppose there
are 4 ath9k-htc usb dongles working, kernel has to consume about
4*50KBytes RAM to cache firmware for all dongles. After applying the
patch, kernel only caches one single firmware image in RAM for
all ath9k-htc devices just during system suspend/resume cycle.
When system is ready for loading firmware, ath9k-htc can request
the loading from usersapce. During system resume, ath9k-htc still
can load the firmware which was cached in kernel memory before
system suspend.
Cc: ath9k-devel@lists.ath9k.org
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature had been disabled in ath9k because the code to support
it was incomplete, but now the code is in sync with the internal QCA
codebase, so it's time to enable it.
On many newer devices, the calibration is assumed to be done with PA
linearization enabled.
Tests with a particular AR933x device showed that the signal emitted
at full power was highly distorted and unreliable with PA linearization
disabled. With this patch, the signal becomes clear and stability
is improved.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before PAPRD training can run, the card needs to have sent a packet for
thermal calibration. Sending a dummy packet with the PAPRD training flag
set causes a crash under some circumstance.
Fix the code by replacing the dummy tx with a delay that waits for a
real packet tx to have occurred.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Re-train if the calibrated PA linearization curve is out of bounds
(affects AR933x and AR9485).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt is no longer handling it. While it shouldn't fire (wraparound
is highly unlikely), the consequences would be fatal (interrupt storm).
Disable the interrupt to prevent that from happening.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of changes in the supported rates set for a given station, it is now
possible to use this callback to update the current internal state of the
station in the htc driver.
Reported-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_rx_tasklet() calls ath9k_rx_skb_preprocess() and ath9k_rx_skb_postprocess()
in a loop over the received frames. The decrypt_error flag is
initialized to false
just outside ath_rx_tasklet() loop. ath9k_rx_accept(), called by
ath9k_rx_skb_preprocess(),
only sets decrypt_error to true and never to false.
Then ath_rx_tasklet() calls ath9k_rx_skb_postprocess() and passes
decrypt_error to it.
So, after a decryption error, in ath9k_rx_skb_postprocess(), we can
have a leftover value
from another processed frame. In that case, the frame will not be marked with
RX_FLAG_DECRYPTED even if it is decrypted correctly.
When using CCMP encryption this issue can lead to connection stuck
because of CCMP
PN corruption and a waste of CPU time since mac80211 tries to decrypt an already
deciphered frame with ieee80211_aes_ccm_decrypt.
Fix the issue initializing decrypt_error flag at the begging of the
ath_rx_tasklet() loop.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This could make rc_stats more simpler and ease the debugging.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ctrl_rate, cw40index, sgi_index, ht_index and calculate
the rate index for TX status from the valid_rate_index that
is populated at initialization time.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calculate the final rate index inside ath_rc_tx_status().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current method of assigning the RTS/CTS rate is completely
broken for HT mode and breaks P2P operation. Fix this by using
the basic_rates provided to the driver by mac80211. For now,
choose the lowest supported basic rate for HT frames.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k: Change rate control to use legacy rate as last MRR"
resulted in the mixing of HT/legacy rates in a single rateset,
which is undesirable. Revert this behavior.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trim API and remove unused variables.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A reference to the rate table is stored inside the
private structure, so there is no need to pass "rate_table"
around.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove various local variables that duplicate information
already stored in mac80211.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During suspend, the device will be moved to FULLSLEEP state.
As btcoex is never been stopped, the btcoex timer is running
and tries to access hw on fullsleep state. Fix that.
Cc: stable@vger.kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit b74713d04e
"ath9k: Handle fatal interrupts properly" introduced a race condition, where
IRQs are being left enabled, however the irq handler returns IRQ_HANDLED
while the reset is still queued without addressing the IRQ cause.
This leads to an IRQ storm that prevents the system from even getting to
the reset code.
Fix this by disabling IRQs in the handler without touching intr_ref_cnt.
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The first part of the power array is initialized in a loop
and the last two values are initialized separately. Extend
the loop to cover the last two items, and remove the separate
initialization.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR1111 is same as AR9485. The h/w
difference between them is quite insignificant,
Felix suggests only very few baseband features
may not be available in AR1111. The h/w code for
AR9485 is already present, so AR1111 should
work fine with the addition of its PID/VID.
Cc: stable@vger.kernel.org [2.6.39+]
Cc: Felix Bitterli <felixb@qca.qualcomm.com>
Reported-by: Tim Bentley <Tim.Bentley@Gmail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: Tim Bentley <Tim.Bentley@Gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the control.sta pointer from ieee80211_tx_info to free up
sufficient space in the TX skb control buffer for the upcoming
Transmit Power Control (TPC).
Instead, the pointer is now on the stack in a new control struct
that is passed as a function parameter to the drivers' tx method.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[reworded commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
