The futex init function is called init(). This is a pain in the neck
when debugging when you code dies in ... init :-)
This renames it to futex_init().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
add_reserved_region() tries to keep the resource list sorted, so when
looking for a place to insert the new resource, it may break out
before the last entry.
When this happens, the list is broken in two because the sibling field
of the new entry doesn't point to the next resource. Fix it by
updating the new resource's sibling field appropriately.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Only request I/O ports 0x295-0x296 instead of the full I/O address
range. This solves a conflict with PNP resources on a few motherboards.
Also request the I/O ports in two parts (4 low ports, 4 high ports)
during device detection, otherwise the PNP resource makes the request
(and thus the detection) fail.
This fixes lm-sensors ticket #2306:
http://www.lm-sensors.org/ticket/2306
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The function thermal_cooling_device_register always returns either a valid
pointer or a value made with ERR_PTR, so a test for non-zero on the result
will always succeed.
The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
//<smpl>
@a@
expression E, E1;
statement S,S1;
position p;
@@
E = thermal_cooling_device_register(...)
... when != E = E1
if@p (E) S else S1
@n@
position a.p;
expression E,E1;
statement S,S1;
@@
E = NULL
... when != E = E1
if@p (E) S else S1
@depends on !n@
expression E;
statement S,S1;
position a.p;
@@
* if@p (E)
S else S1
//</smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This make "cat /proc/${PID}/pagemap" more efficient for
32-bit tasks.
Based upon a report by Mariusz Kozlowski.
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 BEET output function is incorrectly including the inner
header in the payload to be protected. This causes a crash as
the packet doesn't actually have that many bytes for a second
header.
The IPv4 BEET output on the other hand is broken when it comes
to handling an inner IPv6 header since it always assumes an
inner IPv4 header.
This patch fixes both by making sure that neither BEET output
function touches the inner header at all. All access is now
done through the protocol-independent cb structure. Two new
attributes are added to make this work, the IP header length
and the IPv4 option length. They're filled in by the inner
mode's output function.
Thanks to Joakim Koskela for finding this problem.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: fix performance drop for glx
x86: fix trim mtrr not to setup_memory two times
x86: GEODE: add missing module.h include
x86, cpufreq: fix Speedfreq-SMI call that clobbers ECX
x86: fix memoryless node oops during boot
x86: add dmi quirk for io_delay
x86: convert mtrr/generic.c to kernel-doc
x86: Documentation/i386/IO-APIC.txt: fix description
Running the counters testcase from libhugetlbfs results in on 2.6.25-rc5
and 2.6.25-rc5-mm1:
BUG: soft lockup - CPU#3 stuck for 61s! [counters:10531]
NIP: c0000000000d1f3c LR: c0000000000d1f2c CTR: c0000000001b5088
REGS: c000005db12cb360 TRAP: 0901 Not tainted (2.6.25-rc5-autokern1)
MSR: 8000000000009032 <EE,ME,IR,DR> CR: 48008448 XER: 20000000
TASK = c000005dbf3d6000[10531] 'counters' THREAD: c000005db12c8000 CPU: 3
GPR00: 0000000000000004 c000005db12cb5e0 c000000000879228 0000000000000004
GPR04: 0000000000000010 0000000000000000 0000000000200200 0000000000100100
GPR08: c0000000008aba10 000000000000ffff 0000000000000004 0000000000000000
GPR12: 0000000028000442 c000000000770080
NIP [c0000000000d1f3c] .return_unused_surplus_pages+0x84/0x18c
LR [c0000000000d1f2c] .return_unused_surplus_pages+0x74/0x18c
Call Trace:
[c000005db12cb5e0] [c000005db12cb670] 0xc000005db12cb670 (unreliable)
[c000005db12cb670] [c0000000000d24c4] .hugetlb_acct_memory+0x2e0/0x354
[c000005db12cb740] [c0000000001b5048] .truncate_hugepages+0x1d4/0x214
[c000005db12cb890] [c0000000001b50a4] .hugetlbfs_delete_inode+0x1c/0x3c
[c000005db12cb920] [c000000000103fd8] .generic_delete_inode+0xf8/0x1c0
[c000005db12cb9b0] [c0000000001b5100] .hugetlbfs_drop_inode+0x3c/0x24c
[c000005db12cba50] [c00000000010287c] .iput+0xdc/0xf8
[c000005db12cbad0] [c0000000000fee54] .dentry_iput+0x12c/0x194
[c000005db12cbb60] [c0000000000ff050] .d_kill+0x6c/0xa4
[c000005db12cbbf0] [c0000000000ffb74] .dput+0x18c/0x1b0
[c000005db12cbc70] [c0000000000e9e98] .__fput+0x1a4/0x1e8
[c000005db12cbd10] [c0000000000e61ec] .filp_close+0xb8/0xe0
[c000005db12cbda0] [c0000000000e62d0] .sys_close+0xbc/0x134
[c000005db12cbe30] [c00000000000872c] syscall_exit+0x0/0x40
Instruction dump:
ebbe8038 38800010 e8bf0002 3bbd0008 7fa3eb78 38a50001 7ca507b4 4818df25
60000000 38800010 38a00000 7c601b78 <7fa3eb78> 2f800010 409d0008 38000010
This was tracked down to a potential livelock in
return_unused_surplus_hugepages(). In the case where we have surplus
pages on some node, but no free pages on the same node, we may never
break out of the loop. To avoid this livelock, terminate the search if
we iterate a number of times equal to the number of online nodes without
freeing a page.
Thanks to Andy Whitcroft and Adam Litke for helping with debugging and
the patch.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we show the surplus hugetlb pool state in /proc/meminfo, but
not in the per-node meminfo files, even though we track the information
on a per-node basis. Printing it there can help track down dynamic pool
bugs including the one in the follow-on patch.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix the 3D performance drop reported at:
http://bugzilla.kernel.org/show_bug.cgi?id=10328
fb drivers are using ioremap()/ioremap_nocache(), followed by mtrr_add with
WC attribute. Recent changes in page attribute code made both
ioremap()/ioremap_nocache() mappings as UC (instead of previous UC-). This
breaks the graphics performance, as the effective memory type is UC instead
of expected WC.
The correct way to fix this is to add ioremap_wc() (which uses UC- in the
absence of PAT kernel support and WC with PAT) and change all the
fb drivers to use this new ioremap_wc() API.
We can take this correct and longer route for post 2.6.25. For now,
revert back to the UC- behavior for ioremap/ioremap_nocache.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
we could call find_max_pfn() directly instead of setup_memory() to get
max_pfn needed for mtrr trimming.
otherwise setup_memory() is called two times... that is duplicated...
[ mingo@elte.hu: both Thomas and me simulated a double call to
setup_bootmem_allocator() and can confirm that it is a real bug
which can hang in certain configs. It's not been reported yet but
that is probably due to the relatively scarce nature of
MTRR-trimming systems. ]
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Wed, 26 Mar 2008 11:56:22 -0600
Jordan Crouse <jordan.crouse@amd.com> wrote:
> On 26/03/08 14:31 +0100, Stefan Pfetzing wrote:
> > Hello Jordan,
> >
> > I just tried to build your geodwdt driver for the geode watchdog. Therefore
> > I pulled your repository from http://git.infradead.org/geode.git (or more,
> > the git url).
> >
> > I tried to build the geodewdt driver as a module - which didn't work, and
> > it failed with the same problem as earlier mentioned on lkmk [1]. I also
> > checked the fix [2], but that seems to be already in your (or linus) tree -
> > and so I'm unsure what the problem is.
> >
> > [1] http://kerneltrap.org/mailarchive/linux-kernel/2008/2/17/884074
> > [2] http://kerneltrap.org/mailarchive/linux-kernel/2008/2/17/884174
> >
> > Building directly into the kernel seems to work.
> >
> > Maybe you have some idea?
>
> Hmm - that is strange. Exporting the symbols should work. I recommend
> starting over with a clean tree.
>
> CCing Andres - any thoughts?
>
> Jordan
>
Er, yeah. The patch below should fix it. This should probably go into
2.6.25.
Oops, EXPORT_SYMBOL_GPL wasn't being declared due to this header
being missing.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I have found that using SMI to change the cpu's frequency on my DELL
Latitude L400 clobbers the ECX register in speedstep_set_state, causing
unneccessary retries because the "state" variable has changed silently (GCC
assumes it is still present in ECX).
play safe and avoid gcc caching any register across IO port accesses
that trigger SMIs.
Signed-off by: <Stephan.Diestelhorst@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Convert function comment blocks to kernel-doc notation.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The description of the interrupt routing doesn't match the (nice) diagram.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'slab-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/christoph/vm:
slab: fix cache_cache bootstrap in kmem_cache_init()
count_partial() is not used if !SLUB_DEBUG and !CONFIG_SLABINFO
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-hrt:
NOHZ: reevaluate idle sleep length after add_timer_on()
clocksource: revert: use init_timer_deferrable for clocksource_watchdog
The RDMACTXT_F_LAST_CTXT bit was getting set incorrectly
when the last chunk in the read-list spanned multiple pages. This
resulted in a kernel panic when the wrong context was used to
build the RPC iovec page list.
RDMA_READ is used to fetch RPC data from the client for
NFS_WRITE requests. A scatter-gather is used to map the
advertised client side buffer to the server-side iovec and
associated page list.
WR contexts are used to convey which scatter-gather entries are
handled by each WR. When the write data is large, a single RPC may
require multiple RDMA_READ requests so the contexts for a single RPC
are chained together in a linked list. The last context in this list
is marked with a bit RDMACTXT_F_LAST_CTXT so that when this WR completes,
the CQ handler code can enqueue the RPC for processing.
The code in rdma_read_xdr was setting this bit on the last two
contexts on this list when the last read-list chunk spanned multiple
pages. This caused the svc_rdma_recvfrom logic to incorrectly build
the RPC and caused the kernel to crash because the second-to-last
context doesn't contain the iovec page list.
Modified the condition that sets this bit so that it correctly detects
the last context for the RPC.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Tested-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 8fa5913d54, which
caused various interesting problems for people, including wrong resource
allocations. See for example bugzilla entry "2.6.25-rc2: ohci1394
problem (MMIO broken)" at
http://bugzilla.kernel.org/show_bug.cgi?id=10080
And Gary Hade says:
"The same change had also exposed an issue reported by Paul Martin that
has been causing an Oops while hotplugging ThinkPads to a ThinkPad
Dock II. See
http://lkml.org/lkml/2008/2/19/405http://bugzilla.kernel.org/show_bug.cgi?id=9961
I have a fix for the ThinkPad docking Oops but if the issue being
discussed here is caused by the transparent bridge sizing removal
change I totally agree that it should be reverted."
The transparent bridge sizing removal change was motivated by
insufficient PCI memory resource for a transparent bridge window that
was being created as a result of expansion ROM(s) being included in
the transparent bridge sizing calculations.
A later "PCI: Remove default PCI expansion ROM memory allocation"
change ( re: http://lkml.org/lkml/2007/12/11/361 ) removes the
expansion ROM(s) from the transparent bridge sizing calculations which
actually resolves the original issue in a different manner. So, even
if the "PCI: remove transparent bridge sizing" is not problematic it
is no longer needed anyway."
Identified-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Tested-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have been printing these messages at KERN_ERR since 2.6.24,
per http://bugzilla.kernel.org/show_bug.cgi?id=9535
But KERN_ERR pops up on a console booted with "quiet"
and causes users to get alarmed and file bugs
about the message itself:
https://bugzilla.redhat.com/show_bug.cgi?id=436589
So reduce the severity of these messages to
KERN_WARNING, which is not printed by "quiet".
This message will still be seen without "quiet",
but a lot of messages are printed in that mode
and it will be less likely to cause undue alarm.
We could go all the way to KERN_DEBUG, but this
is a real warning after all, so it seems prudent
not to require "debug" to see it.
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 556a169dab ("slab: fix bootstrap on
memoryless node") introduced bootstrap-time cache_cache list3s for all nodes
but forgot that initkmem_list3 needs to be accessed by [somevalue + node]. This
patch fixes list_add() corruption in mm/slab.c seen on the ES7000.
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Olaf Hering <olaf@aepfle.de>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Dan Yeisley <dan.yeisley@unisys.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Avoid warnings about unused functions if neither SLUB_DEBUG nor CONFIG_SLABINFO
is defined. This patch will be reversed when slab defrag is merged since slab
defrag requires count_partial() to determine the fragmentation status of
slab caches.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Add device tree file for Emerson KSI8560 board.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add default config for Emerson KSI8560 board.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add boot wrapper for Emerson KSI8560 board.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The KSI8560 is a single compact, mid-, or full-size Advanced Mezzanine Card
(AdvancedMC™) based on the Freescale™ Semiconductor MPC8560 PowerQUICC III™
microprocessor. This product will serve in data and signaling applications such
as signaling gateways (SGW) and softswitch signaling interface cards.
The board has altera maxii CPLD, that is used to obtain and manage board
configuration. Also there are two SCC UART serial consoles and FCC ethernet,
that is routed to the front panel, while other ethernet controlers (TSEC's) are
routed to the backplane.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 4b6f5b3a99.
bsg takes a reference to the underlying generic device, so it's
impossible to unregister bsg in the device release routine.
Acked-by: FUJITA Tomonori <tomof@acm.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds the L2 cache node to the Taishan 440GX dts file.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds support for the 256k L2 cache found on some IBM/AMCC
4xx PPC's. It introduces a common 4xx SoC file (sysdev/ppc4xx_soc.c)
which currently "only" adds the L2 cache init code. Other common 4xx
stuff can be added later here.
The L2 cache handling code is a copy of Eugene's code in arch/ppc
with small modifications.
Tested on AMCC Taishan 440GX.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Currently Haleakala uses the Kilauea platform code. This patch adds
"haleakala" to the compatible property, in case later kernel versions
will introduce a Haleakala platform code.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The patch adds the Glacier dts. The Glacier is nearly identical to the
Canyonlands (460EX). Here the differences:
- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Major 259 has been assigned by lanana. Use it. Also, publish
/dev/icap[0-k] as the device entries, and register platform devices
named 'icap' to be consistent.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
It appears that in some cases, the sync word might not be recognized
by the hardware correctly. If this happens, then attempting to read
from the port results in an unrecoverable error because of the design
of the FPGA core. This patch updates the code to check the status of
the device before reading the IDCODE, in order to avoid entering this
unrecoverable state. This patch also adds additional NOOP commands
into the sychronization sequence, which appears to be necessary to
avoid the condition on some hardware.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Both the buffer-based and fifo-based icap cores have a status
register. Previously, this was only used internally to check whether
transactions have completed. However, the status can be useful to the
main driver as well. This patch exposes these status functions to the
main driver along with some masks for the differnet bits.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds TAH (TCP/IP Acceleration Hardware) support to the
taishan 440GX dts. It depends on the NEWEMAC/tah patch that adds the
compatible "ibm,tah" property to the matching table.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds dcri_clrset() macro which does read/modify/write
on indirect dcr registers while holding indirect dcr lock.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The AMCC 440EP Yosemite board is very similar to the original AMCC Bamboo
board. This adds a YOSEMITE option to Kconfig, and reuses the existing
bamboo board support in the kernel.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
All this code is needed to properly initialize the 460EX PCIe host
bridge(s). We re-initialize all ports again, even though this has been done
in the bootloader (U-Boot) before. This way we make sure, that we always
run the latest init code in Linux and don't depend on code versions from
U-Boot.
Unfortunately all IBM/AMCC chips currently supported in this PCIe driver need
a different reset-/init-sequence.
Tested on AMCC Canyonlands eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
