Some of the ARM_ERRATA selection is not done in the initial SOC support
patches. This patch selects 2 new ARM_ERRATA's and removes one which was
actually fixed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
[olof: reorder new errata entries]
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fixes a bug in pinctrl setup of serial2 device, Some of the
pins in the pinctrl node of serial2 do not belong to that
pin-controller. This patch divides them in the pins into there
respective pin controller nodes.
Without this patch serial on StiH416-B2000 Board will not work as it
fails with:
"st-pinctrl pin-controller-rear.3: failed to get pin(99) name
st-pinctrl pin-controller-rear.3: maps: function serial2 group serial2-0
num 4
pinconfig core: failed to register map default (3): no group/pin given"
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Change to using max P-state instead of max turbo P-state. This
change resolves two issues.
On a quiet system intel_pstate can fail to respond to a load change.
On CPU SKUs that have a limited number of P-states and no turbo range
intel_pstate fails to select the highest available P-state.
This change is suitable for stable v3.9+
References: https://bugzilla.kernel.org/show_bug.cgi?id=59481
Reported-and-tested-by: Arjan van de Ven <arjan@linux.intel.com>
Reported-and-tested-by: dsmythies@telus.net
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some of the fixes need to go back to 3.10. They are minor, and deal mostly
with incorrect ref counting in accessing event files.
There was a couple of optimizations that should have perf perform a bit
better when accessing trace events.
And some various clean ups. Some of the clean ups are necessary to help
in a fix to a theoretical race between opening a event file and
deleting that event.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJR7TuSAAoJEOdOSU1xswtMFsEIALOQWth+jUEmd+TJNMgW7vHd
aJ4pjc0Br2ur0XOm4xsOOsuexQ/sKG4J0qJT4z01Ny4ZJ6UcL6CvLKlQXlySrUw5
POH6+7B7os3ikav+4KGDYJpeyR7l+uveA7IcqZz5OWAbz2yi3HbluPUUyFn+62ic
Q0IOi4KkCly4buHNqJqfQRUo+0eBb8sZUfaklIQE07Dd66YVyq4w2WogI2PxBanP
b6p4sE9n7wf7GxXXur5jPBz8PheAFu6a6dM9d9BX28ia79OGSGN4mYWbSNOn8wzl
gJr1ZqxKJBq73IHpNV7QBOCCgDJ9vtuqxKKm4kuLCMfjCTPBsQ3Bmo/qJulnnGI=
=AlmI
-----END PGP SIGNATURE-----
Merge tag 'trace-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes and cleanups from Steven Rostedt:
"This contains fixes, optimizations and some clean ups
Some of the fixes need to go back to 3.10. They are minor, and deal
mostly with incorrect ref counting in accessing event files.
There was a couple of optimizations that should have perf perform a
bit better when accessing trace events.
And some various clean ups. Some of the clean ups are necessary to
help in a fix to a theoretical race between opening a event file and
deleting that event"
* tag 'trace-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Kill the unbalanced tr->ref++ in tracing_buffers_open()
tracing: Kill trace_array->waiter
tracing: Do not (ab)use trace_seq in event_id_read()
tracing: Simplify the iteration logic in f_start/f_next
tracing: Add ref_data to function and fgraph tracer structs
tracing: Miscellaneous fixes for trace_array ref counting
tracing: Fix error handling to ensure instances can always be removed
tracing/kprobe: Wait for disabling all running kprobe handlers
tracing/perf: Move the PERF_MAX_TRACE_SIZE check into perf_trace_buf_prepare()
tracing/syscall: Avoid perf_trace_buf_*() if sys_data->perf_events is empty
tracing/function: Avoid perf_trace_buf_*() if event_function.perf_events is empty
tracing: Typo fix on ring buffer comments
tracing: Use trace_seq_puts()/trace_seq_putc() where possible
tracing: Use correct config guard CONFIG_STACK_TRACER
Pull thermal management fixes from Zhang Rui:
"These are fixes collected over the last week, they fixes several
problems caused by the x86_pkg_temp_thermal introduced in 3.11-rc1.
Specifics:
- the x86_pkg_temp_thermal driver causes crash on systems with no
package MSR support as there is a bug in the logic to check
presence of DTHERM and PTS feature together. Added a change so
that when there is no PTS support, module doesn't get loaded.
- fix krealloc() misuse in pkg_temp_thermal_device_add().
If krealloc() returns NULL, it doesn't free the original. Thus if
we want to exit because of the krealloc() failure, we must make
sure the original one is freed.
- The error code path of the x86 package temperature thermal driver's
initialization routine makes an unbalanced call to
get_online_cpus(), which causes subsequent CPU offline operations,
and consequently system suspend, to permanently block in
cpu_hotplug_begin() on systems where get_core_online() returns an
error code.
Remove the extra get_online_cpus() to fix the problem"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
Thermal: Fix lockup of cpu_down()
Thermal: x86_pkg_temp: Limit number of pkg temp zones
Thermal: x86_pkg_temp: fix krealloc() misuse in in pkg_temp_thermal_device_add()
Thermal: x86 package temp thermal crash
- OMAP device tree boot fix
- Handle an error condition in the MSM driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=Ld25
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
"A first round of GPIO fixes for the v3.11 series:
- OMAP device tree boot fix
- Handle an error condition in the MSM driver
The OMAP patches have been around since around the merge window, but
since they first caused more breakage I let them boil in -next for a
while. These should be fine now"
* tag 'gpio-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
drivers: gpio: msm: Fix the error condition for reading ngpio
gpio/omap: fix build error when OF_GPIO is not defined.
gpio/omap: auto request GPIO as input if used as IRQ via DT
gpio/omap: don't create an IRQ mapping for every GPIO on DT
Pull block IO driver bits from Jens Axboe:
"As I mentioned in the core block pull request, due to real life
circumstances the driver pull request would be late. Now it looks
like -rc2 late... On the plus side, apart form the rsxx update, these
are all things that I could argue could go in later in the cycle as
they are fixes and not features. So even though things are late, it's
not ALL bad.
The pull request contains:
- Updates to bcache, all bug fixes, from Kent.
- A pile of drbd bug fixes (no big features this time!).
- xen blk front/back fixes.
- rsxx driver updates, some of them deferred form 3.10. So should be
well cooked by now"
* 'for-3.11/drivers' of git://git.kernel.dk/linux-block: (63 commits)
bcache: Allocation kthread fixes
bcache: Fix GC_SECTORS_USED() calculation
bcache: Journal replay fix
bcache: Shutdown fix
bcache: Fix a sysfs splat on shutdown
bcache: Advertise that flushes are supported
bcache: check for allocation failures
bcache: Fix a dumb race
bcache: Use standard utility code
bcache: Update email address
bcache: Delete fuzz tester
bcache: Document shrinker reserve better
bcache: FUA fixes
drbd: Allow online change of al-stripes and al-stripe-size
drbd: Constants should be UPPERCASE
drbd: Ignore the exit code of a fence-peer handler if it returns too late
drbd: Fix rcu_read_lock balance on error path
drbd: fix error return code in drbd_init()
drbd: Do not sleep inside rcu
bcache: Refresh usage docs
...
Received packets are only scattered if this is enabled in both the
matching filter and the receiving queue. This was not being done for
filters inserted for RFS, so any packet requiring more than a single
descriptor was dropped.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 4bb1667255 (build some drivers only
when compile-testing), PTP_1588_CLOCK_PCH depends on (X86 ||
COMPILE_TEST). But PCH_GBE selects PTP_1588_CLOCK_PCH without
depending on x86. Fix this by adding the same dependency here.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: <fengguang.wu@intel.com> [intel's build test robot]
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: kbuild-all@01.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contains Netfilter fixes for your net tree,
they are:
* Fix potential NULL dereference in the socket match if revision 0
is used, from Eric Dumazet.
* Fix missing expectation NAT initialization that results in dumping
the NAT part via ctnetlink, thus leading to problems in expectation
synchronization through conntrackd, from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sata_inic162x never reached a state where it's reliable enough for
production use and data corruption is a relatively common occurrence.
Make the driver generate warning about the issues and mark the Kconfig
option as experimental.
If the situation doesn't improve, we'd be better off making it depend
on CONFIG_BROKEN. Let's wait for several cycles and see if the kernel
message draws any attention.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Martin Braure de Calignon <braurede@free.fr>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Reported-by: risc4all@yahoo.com
This warning has been introduced by the commit
0f9bc4bcdf pinctrl: single: adopt pinctrl sleep mode management
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The usage of strict_strtol() is not preferred, because
strict_strtol() is obsolete. Thus, kstrtol() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
To avoid ending up in a NULL-pointer access, the function
brcmf_txflowblock_if() should only be called for interfaces
that have a netdev associated with it.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the transmit fails because there are no hanger slots or
any other reason and the packet was an EAPOL packet the
pending counter should be decreased although it was not
transmitted so the driver does not end up in a dead-lock.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Building driver wil6210 in 3.10 and 3.11 kernels yields the following errors:
CC [M] drivers/net/wireless/ath/wil6210/debugfs.o
drivers/net/wireless/ath/wil6210/debugfs.c: In function 'wil_print_ring':
drivers/net/wireless/ath/wil6210/debugfs.c:163:11: error: pointer targets in passing argument 5 of 'hex_dump_to_buffer' differ in signedness [-Werror=pointer-sign]
false);
^
In file included from include/linux/kernel.h:13:0,
from include/linux/cache.h:4,
from include/linux/time.h:4,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/net/wireless/ath/wil6210/debugfs.c:17:
include/linux/printk.h:361:13: note: expected 'char *' but argument is of type 'unsigned char *'
extern void hex_dump_to_buffer(const void *buf, size_t len,
^
drivers/net/wireless/ath/wil6210/debugfs.c: In function 'wil_txdesc_debugfs_show':
drivers/net/wireless/ath/wil6210/debugfs.c:429:10: error: pointer targets in passing argument 5 of 'hex_dump_to_buffer' differ in signedness [-Werror=pointer-sign]
sizeof(printbuf), false);
^
In file included from include/linux/kernel.h:13:0,
from include/linux/cache.h:4,
from include/linux/time.h:4,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/net/wireless/ath/wil6210/debugfs.c:17:
include/linux/printk.h:361:13: note: expected 'char *' but argument is of type 'unsigned char *'
extern void hex_dump_to_buffer(const void *buf, size_t len,
^
cc1: all warnings being treated as errors
make[5]: *** [drivers/net/wireless/ath/wil6210/debugfs.o] Error 1
make[4]: *** [drivers/net/wireless/ath/wil6210] Error 2
make[3]: *** [drivers/net/wireless/ath] Error 2
make[2]: *** [drivers/net/wireless] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
These errors are fixed by changing the type of the buffer from "unsigned char *" to "char *".
Reported-by: Thomas Fjellstrom <thomas@fjellstrom.ca>
Tested-by: Thomas Fjellstrom <thomas@fjellstrom.ca>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.10]
Cc: Thomas Fjellstrom <thomas@fjellstrom.ca>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In monitor mode, priv->vif is NULL, but at one point in the receive path we
blindly attempt to dereference it. Add a test to prevent this.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently ath9k_htc will reboot firmware only if interface was
ever started. Which lead to the problem in case where interface
was never started but module need to be reloaded.
This patch will partially fix bug "ath9k_htc: Target is unresponsive"
https://github.com/qca/open-ath9k-htc-firmware/issues/1
Reproduction case:
- plug adapter
- make sure nothing will touch it. Stop Networkmanager or blacklist mac address of this adapter.
- rmmod ath9k_htc; sleep 1; modprobe ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we configure harwdare and clock, only after
interface start. In this case, if we reload module or
reboot PC without configuring adapter, firmware will freeze.
There is no software way to reset adpter.
This patch add initial configuration and set it in
disabled state, to avoid this freeze. Behaviour of this patch
should be similar to: ifconfig wlan0 up; ifconfig wlan0 down.
Bug: https://github.com/qca/open-ath9k-htc-firmware/issues/1
Tested-by: Bo Shi <cnshibo@gmail.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During tear down (e.g. mwifiex_sdio_remove during system suspend),
mwifiex left IRQs enabled for a significant period of time when it was
unable to handle them correctly. This caused interrupt storms and
interfered with the bluetooth interface on the same SDIO card.
Solve this by disabling interrupts at the point when they can no longer
be handled correctly, which is at the start of mwifiex_remove_card().
For cleanliness, we now enable interrupts in the mwifiex_add_card() path,
to be symmetrical with the disabling of interrupts. We also couple the
registration of the sdio IRQ handler with the actual enable/disable of
interrupts at the hardware level.
I also removed a write to this register in mwifiex_init_sdio which seemed
pointless and won't cause any ill effects now that we only register
the SDIO IRQ handler when we are ready to accept interrupts.
Includes some corrections from Amitkumar Karwar.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Noticed that my old Radeon 7500 hung after printing
drm: GPU not posted. posting now...
when it wasn't selected as the primary card the BIOS. Some digging
revealed that it was hanging in combios_parse_mmio_table() while
parsing the ASIC INIT 3 table. Looking at the BIOS ROM for the card,
it becomes obvious that there is no ASIC INIT 3 table in the BIOS.
The code is just processing random garbage. No surprise it hangs!
Why do I say that there is no ASIC INIT 3 table is the BIOS? This
table is found through the MISC INFO table. The MISC INFO table can
be found at offset 0x5e in the COMBIOS header. But the header is
smaller than that. The COMBIOS header starts at offset 0x126. The
standard PCI Data Structure (the bit that starts with 'PCIR') lives at
offset 0x180. That means that the COMBIOS header can not be larger
than 0x5a bytes and therefore cannot contain a MISC INFO table.
I looked at a dozen or so BIOS images, some my own, some downloaded from:
<http://www.techpowerup.com/vgabios/index.php?manufacturer=ATI&page=1>
It is fairly obvious that the size of the COMBIOS header can be found
at offset 0x6 of the header. Not sure if it is a 16-bit number or
just an 8-bit number, but that doesn't really matter since the tables
seems to be always smaller than 256 bytes.
So I think combios_get_table_offset() should check if the requested
table is present. This can be done by checking the offset against the
size of the header. See the diff below. The diff is against the WIP
OpenBSD codebase that roughly corresponds to Linux 3.8.13 at this
point. But I don't think this bit of the code changed much since
then.
For what it is worth:
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Hopefully avoid more quirks in the future due to bogus
vbios dac data.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Hello,
got another card with "too bright" problem:
Sapphire Radeon VE 7000 DDR (VGA+S-Video)
lspci -vnn:
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RV100 QY [Radeon 7000/VE] [1002:5159] (prog-if 00 [VGA controller])
Subsystem: PC Partner Limited Sapphire Radeon VE 7000 DDR [174b:7c28]
The patch below fixes the problem for this card.
But I don't like the blacklist, couldn't some heuristic be used instead?
The interesting thing is that the manufacturer is the same as the other card
needing the same quirk. I wonder how many different types are broken this way.
The "wrong" ps2_pdac_adj value that comes from BIOS on this card is 0x300.
====================
drm/radeon: Add primary dac adj quirk for Sapphire Radeon VE 7000 DDR
Values from BIOS are wrong, causing too bright colors.
Use default values instead.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The atom interpreter expects data in LE format, so
swap the message buffer as apprioriate.
v2: properly handle non-dw aligned byte counts.
v3: properly handle remainder
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Dong He <hedonghust@gmail.com>
Cc: stable@vger.kernel.org
Make sure the 3D engine is idle before using CP DMA for
bo copies.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Marek Olšák <maraeo@gmail.com>
The PFC pinctrl driver on sh73a0 is also regiatering a VccQ regulator for
SDHI0. However, its consumers list only included the platform-data based
SDHI device name. When booted with DT SDHI0 couldn't enable VccQ and
therefore was unusable. Fix this by adding a consumer with DT-based name.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It almost does not matter because most users use only the ->start member
of the struct. However if this struct is passed to a platform device
which is then added via platform_device_add() then the ->parent member is
also used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
list_first_entry() expects the list is not empty, we need to check if list is
empty before calling list_first_entry(). Thus use list_first_entry_or_null()
instead of list_first_entry().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This prefix will be used in various compatible properties
for the devices from Qualcomm Atheros, Inc.
Cc: Luis R. Rodriguez <rodrigue@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Device tree bindings require a lot more attention than they used to.
We've got a group of volunteers willing to take over maintaining
bindings. This patch adds them to the MAINTAINERS file.
This group still needs to work out a process for maintainership and how
they are going to work together. I recommend that they set up a shared
tree on git.kernel.org that they each have commit access to similar to
the tip tree or the arm-soc tree, but it is up to them.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Unfortunately, I'm no longer to spend the time needed on maintainership.
It is time for me to step aside and pass maintainership to other
engineers. I'm not disappearing from Linux development, but it would be
irresponsible for me to hold onto a job that I am unable to do.
v2: Leave my name on devicetree core code maintainership. Rob NAKed that
part of the patch. :)
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Linux Walleij <linus.walleij@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Set the ehci->resuming flag for the port we receive a remote
wakeup on so that resume signalling can be completed.
Without this, the root hub timer will not fire again to check
if the resume was completed and there will be a never-ending wait on
on the port.
This effect is only observed if the HUB IRQ IN does not come after we
have initiated the port resume.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for MMB Networks and Planet Innovation Ingeni ZigBee USB
devices using customized Silicon Labs' CP210x.c USB to UART bridge
drivers with PIDs: 88A4, 88A5.
Signed-off-by: Sami Rahman <sami.rahman@mmbresearch.com>
Tested-by: Sami Rahman <sami.rahman@mmbresearch.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the Schweitzer Engineering Laboratories
C662 USB cable based off the CP210x driver.
Signed-off-by: Barry Grussling <barry@grussling.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch was tested on 3.10.1 kernel.
Same models of Petatel NP10T modems have different device IDs.
Unfortunately they have no additional revision information on a board
which may treat them as different devices. Currently I've seen only
two NP10T devices with various IDs. Possibly Petatel NP10T list will
be appended upon devices with new IDs will appear.
Signed-off-by: Daniil Bolsun <dan.bolsun@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device report an error capacity when read_capacity_16().
Using read_capacity_10() can get the correct capacity.
Signed-off-by: Ren Bigcren <bigcren.ren@sonymobile.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Oskar Andero <oskar.andero@sonymobile.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds NetGear Managed Switch M4100 series, M5300 series, M7100 series
USB ID (0846:0110) to the cp210x driver. Without this, the serial
adapter is not recognized in Linux. Description was obtained from
an Netgear Eng.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a469abd0f8 ("ARM: elf: add new hwcap for identifying atomic
ldrd/strd instructions") added a new hwcap to identify LPAE on CPUs
which support it. Whilst the hwcap data is correct, the string reported
in /proc/cpuinfo actually matches on HWCAP_VFPD32, which was missing
an entry in the string table.
This patch fixes this problem by adding a "vfpd32" string at the correct
offset, preventing us from falsely advertising LPAE on CPUs which do not
support it.
[will: added commit message]
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Set querying_devices flag to true when we start the enumeration
process.
This was missing from the original patch. It never produced
undesirable effects as it is highly improbable to have a second
enumeration triggered while a first one was still in progress.
Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 8af6c08830.
This patch re-adds the workaround introduced by 596264082f
which was reverted by 8af6c08830.
The original patch 596264 was needed to overcome a situation where
the hid-core would drop incoming reports while probe() was being
executed.
This issue was solved by c849a6143b which added
hid_device_io_start() and hid_device_io_stop() that enable a specific
hid driver to opt-in for input reports while its probe() is being
executed.
Commit a9dd22b730 modified hid-logitech-dj so as to use the
functionality added to hid-core. Having done that, workaround 596264
was no longer necessary and was reverted by 8af6c08.
We now encounter a different problem that ends up 'again' thwarting
the Unifying receiver enumeration. The problem is time and usb controller
dependent. Ocasionally the reports sent to the usb receiver to start
the paired devices enumeration fail with -EPIPE and the receiver never
gets to enumerate the paired devices.
With dcd9006b1b the problem was "hidden" as the call to the usb
driver became asynchronous and none was catching the error from the
failing URB.
As the root cause for this failing SET_REPORT is not understood yet,
-possibly a race on the usb controller drivers or a problem with the
Unifying receiver- reintroducing this workaround solves the problem.
Overall what this workaround does is: If an input report from an
unknown device is received, then a (re)enumeration is performed.
related bug:
1194649
Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This SKU was missing in the list of supported devices
https://bugzilla.kernel.org/show_bug.cgi?id=60577
Cc: <stable@vger.kernel.org> [all versions]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch is intended to avoid the buffering to non-assoc mesh STA
and also to avoid the triggering of frame to non-assoc mesh STA which
could cause kernel panic in specific hw.
One of the examples, is kernel panic happens to ath9k if user space
inserts the mesh STA and not proceed with the SAE and AMPE, and later
the same mesh STA is detected again. The sta_state of the mesh STA remains
at IEEE80211_STA_NONE and if the ieee80211_sta_ps_deliver_wakeup is called
and subsequently the ath_tx_aggr_wakeup, the kernel panic due to
ath_tx_node_init is not called before to initialize the require data
structures.
This issue is reported by Cedric Voncken before.
http://www.spinics.net/lists/linux-wireless/msg106342.html
[<831ea6b4>] ath_tx_aggr_wakeup+0x44/0xcc [ath9k]
[<83084214>] ieee80211_sta_ps_deliver_wakeup+0xb8/0x208 [mac80211]
[<830b9824>] ieee80211_mps_sta_status_update+0x94/0x108 [mac80211]
[<83099398>] ieee80211_sta_ps_transition+0xc94/0x34d8 [mac80211]
[<8022399c>] nf_iterate+0x98/0x104
[<8309bb60>] ieee80211_sta_ps_transition+0x345c/0x34d8 [mac80211]
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, compare_cpu_mode_with_primary uses a mixture of macro
arguments and hardcoded registers, and does so incorrectly, as it
stores (__boot_cpu_mode_offset | BOOT_CPU_MODE_MISMATCH) to
(__boot_cpu_mode + &__boot_cpu_mode_offset), which could corrupt an
arbitrary portion of memory.
This patch fixes up compare_cpu_mode_with_primary to use the macro
arguments, correctly updating __boot_cpu_mode.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
